A. Leela Mohana Reddy

Bio: A. Leela Mohana Reddy is an academic researcher from Indian Institute of Technology Madras. The author has contributed to research in topics: Carbon nanotube & High-resolution transmission electron microscopy. The author has an hindex of 15, co-authored 19 publications receiving 1217 citations.

Nanocrystalline Metal Oxides Dispersed Multiwalled Carbon Nanotubes as Supercapacitor Electrodes

Abstract: RuO2/MWNT, TiO2/MWNT, and SnO2/MWNT nanocrystalline composites for supercapacitor electrodes have been synthesized by chemical reduction method using functionalized MWNT and respective salts. MWNT have been synthesized by thermal catalytic chemical vapor deposition (CCVD) over hydrogen decrepitated Mischmetal (Mm)-based AB3 alloy hydride catalysts. Structural and morphological characterizations of metal oxide dispersed MWNT have been carried out using powder X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM and HRTEM), energy dispersive X-ray analysis (EDAX), and Raman spectroscopy. Electrochemical performance of these electrodes has been investigated using cyclic voltammetry, galvanostatic charge−discharge, and electrochemical impedance spectroscopy. Specific capacitance of RuO2, TiO2, and SnO2 dispersed MWNT electrodes increases compared to that pure MWNT electrode due to the pseudo capacitance of the nanocrystalline metal oxides dispersed on the function...

Asymmetric Flexible Supercapacitor Stack

Abstract: Electrical double layer supercapacitor is very significant in the field of electrical energy storage which can be the solution for the current revolution in the electronic devices like mobile phones, camera flashes which needs flexible and miniaturized energy storage device with all non-aqueous components. The multiwalled carbon nanotubes (MWNTs) have been synthesized by catalytic chemical vapor deposition technique over hydrogen decrepitated Mischmetal (Mm) based AB3alloy hydride. The polymer dispersed MWNTs have been obtained by insitu polymerization and the metal oxide/MWNTs were synthesized by sol-gel method. Morphological characterizations of polymer dispersed MWNTs have been carried out using scanning electron microscopy (SEM), transmission electron microscopy (TEM and HRTEM). An assymetric double supercapacitor stack has been fabricated using polymer/MWNTs and metal oxide/MWNTs coated over flexible carbon fabric as electrodes and nafion®membrane as a solid electrolyte. Electrochemical performance of the supercapacitor stack has been investigated using cyclic voltammetry, galvanostatic charge-discharge, and electrochemical impedance spectroscopy.

A review of electrode materials for electrochemical supercapacitors

Abstract: In this critical review, metal oxides-based materials for electrochemical supercapacitor (ES) electrodes are reviewed in detail together with a brief review of carbon materials and conducting polymers. Their advantages, disadvantages, and performance in ES electrodes are discussed through extensive analysis of the literature, and new trends in material development are also reviewed. Two important future research directions are indicated and summarized, based on results published in the literature: the development of composite and nanostructured ES materials to overcome the major challenge posed by the low energy density of ES (476 references).

Ultracapacitors: Why, How, and Where is the Technology

Abstract: The science and technology of ultracapacitors are reviewed for a number of electrode materials, including carbon, mixed metal oxides, and conducting polymers. More work has been done using microporous carbons than with the other materials and most of the commercially available devices use carbon electrodes and an organic electrolytes. The energy density of these devices is 3¯5 Wh/kg with a power density of 300¯500 W/kg for high efficiency (90¯95%) charge/discharges. Projections of future developments using carbon indicate that energy densities of 10 Wh/kg or higher are likely with power densities of 1¯2 kW/kg. A key problem in the fabrication of these advanced devices is the bonding of the thin electrodes to a current collector such the contact resistance is less than 0.1 cm2. Special attention is given in the paper to comparing the power density characteristics of ultracapacitors and batteries. The comparisons should be made at the same charge/discharge efficiency.

Graphene Oxide−MnO2 Nanocomposites for Supercapacitors

Abstract: A composite of graphene oxide supported by needle-like MnO2 nanocrystals (GO−MnO2 nanocomposites) has been fabricated through a simple soft chemical route in a water−isopropyl alcohol system. The formation mechanism of these intriguing nanocomposites investigated by transmission electron microscopy and Raman and ultraviolet−visible absorption spectroscopy is proposed as intercalation and adsorption of manganese ions onto the GO sheets, followed by the nucleation and growth of the crystal species in a double solvent system via dissolution−crystallization and oriented attachment mechanisms, which in turn results in the exfoliation of GO sheets. Interestingly, it was found that the electrochemical performance of as-prepared nanocomposites could be enhanced by the chemical interaction between GO and MnO2. This method provides a facile and straightforward approach to deposit MnO2 nanoparticles onto the graphene oxide sheets (single layer of graphite oxide) and may be readily extended to the preparation of othe...

Synthesis Of Nitrogen-Doped Graphene Films For Lithium Battery Application

Abstract: We demonstrate a controlled growth of nitrogen-doped graphene layers by liquid precursor based chemical vapor deposition (CVD) technique. Nitrogen-doped graphene was grown directly on Cu current collectors and studied for its reversible Li-ion intercalation properties. Reversible discharge capacity of N-doped graphene is almost double compared to pristine graphene due to the large number of surface defects induced due to N-doping. All the graphene films were characterized by Raman spectroscopy, transmission electron microscopy, and X-ray photoemission spectroscopy. Direct growth of active electrode material on current collector substrates makes this a feasible and efficient process for integration into current battery manufacture technology.