Alex K.-Y. Jen

Bio: Alex K.-Y. Jen is an academic researcher from City University of Hong Kong. The author has contributed to research in topics: Perovskite (structure) & Polymer solar cell. The author has an hindex of 128, co-authored 921 publications receiving 61811 citations. Previous affiliations of Alex K.-Y. Jen include University of Nebraska–Lincoln & Zhejiang California International NanoSystems Institute.

Optical micro-resonator chemical sensor

Abstract: Polymers that contain conjugated molecules can change their index of refraction upon bonding with high explosive molecules. These polymers can be incorporated into micro-ring resonators as trace explosive sensor. Since the resonator cavity itself is made of sensing material, the detection is intrinsic, which may lead to higher sensitivity and faster response than other fiber optic chemical sensors. Photobleaching was used for the fabrication of the microrings resonators. The sensor has shown ppb level of sensitivity to the vapor of an explosive stimulant 2,4- dinitrotoluene and is insensitive to common chemical pollutants including nitrates, sulfates and phosphates.

Enhancing the hole injection ability of indium tin oxide via ammonium salts in polymer light-emitting diodes

Abstract: The enhancement of the hole injection ability of indium tin oxide (ITO) by spin-coating ammonium salts onto it is investigated. The work function of the ITO is increased via spin-coating an NH4Br aqueous solution onto it, which is observed using ultra-violet photoelectron spectroscopy. The formation of H-bonds at the interface between the ITO and the NH4Br is corroborated by utilising the surface sensitivity of synchrotron X-ray photoelectron spectroscopy at low photoelectron take-off angles. We illustrate the increase in the work function of the ITO with a possible scheme involving H-bonding between NH4+ and the ITO. Polymer light-emitting diodes (PLEDs) with ITO/NH4Br showed significantly enhanced performances compared to those with ITO only, with higher current density (924 mA cm−2vs. 903 mA cm−2) and brightness (44 224 cd m−2vs. 1987 cd m−2) at a bias voltage of 7.0 V. To confirm the advantages of general ammonium salts for enhancing device performance, PLEDs with ITO coated by NH4Cl, NH4H2PO4, and (NH4)2SO4 were fabricated and their performances were verified.

Electron-hole diffusion lengths exceeding 1 micrometer in an organometal trihalide perovskite absorber.

Abstract: Organic-inorganic perovskites have shown promise as high-performance absorbers in solar cells, first as a coating on a mesoporous metal oxide scaffold and more recently as a solid layer in planar heterojunction architectures. Here, we report transient absorption and photoluminescence-quenching measurements to determine the electron-hole diffusion lengths, diffusion constants, and lifetimes in mixed halide (CH3NH3PbI(3-x)Cl(x)) and triiodide (CH3NH3PbI3) perovskite absorbers. We found that the diffusion lengths are greater than 1 micrometer in the mixed halide perovskite, which is an order of magnitude greater than the absorption depth. In contrast, the triiodide absorber has electron-hole diffusion lengths of ~100 nanometers. These results justify the high efficiency of planar heterojunction perovskite solar cells and identify a critical parameter to optimize for future perovskite absorber development.

Electron-Hole Diffusion Lengths Exceeding 1 Micrometer in an Organometal Trihalide Perovskite Absorber

Abstract: Organic-inorganic perovskites have shown promise as high-performance absorbers in solar cells, first as a coating on a mesoporous metal oxide scaffold and more recently as a solid layer in planar heterojunction architectures. Here, we report transient absorption and photoluminescence-quenching measurements to determine the electron-hole diffusion lengths, diffusion constants, and lifetimes in mixed halide (CH3NH3PbI(3-x)Cl(x)) and triiodide (CH3NH3PbI3) perovskite absorbers. We found that the diffusion lengths are greater than 1 micrometer in the mixed halide perovskite, which is an order of magnitude greater than the absorption depth. In contrast, the triiodide absorber has electron-hole diffusion lengths of ~100 nanometers. These results justify the high efficiency of planar heterojunction perovskite solar cells and identify a critical parameter to optimize for future perovskite absorber development.

Interface engineering of highly efficient perovskite solar cells

Abstract: Advancing perovskite solar cell technologies toward their theoretical power conversion efficiency (PCE) requires delicate control over the carrier dynamics throughout the entire device. By controlling the formation of the perovskite layer and careful choices of other materials, we suppressed carrier recombination in the absorber, facilitated carrier injection into the carrier transport layers, and maintained good carrier extraction at the electrodes. When measured via reverse bias scan, cell PCE is typically boosted to 16.6% on average, with the highest efficiency of ~19.3% in a planar geometry without antireflective coating. The fabrication of our perovskite solar cells was conducted in air and from solution at low temperatures, which should simplify manufacturing of large-area perovskite devices that are inexpensive and perform at high levels.

Aggregation-Induced Emission: Together We Shine, United We Soar!

Abstract: Ju Mei,†,‡,∥ Nelson L. C. Leung,†,‡,∥ Ryan T. K. Kwok,†,‡ Jacky W. Y. Lam,†,‡ and Ben Zhong Tang*,†,‡,§ †HKUST-Shenzhen Research Institute, Hi-Tech Park, Nanshan, Shenzhen 518057, China ‡Department of Chemistry, HKUST Jockey Club Institute for Advanced Study, Institute of Molecular Functional Materials, Division of Biomedical Engineering, State Key Laboratory of Molecular Neuroscience, Division of Life Science, The Hong Kong University of Science and Technology, Clear Water Bay, Kowloon, Hong Kong, China Guangdong Innovative Research Team, SCUT-HKUST Joint Research Laboratory, State Key Laboratory of Luminescent Materials and Devices, South China University of Technology, Guangzhou 510640, China

High-performance photovoltaic perovskite layers fabricated through intramolecular exchange

Abstract: The band gap of formamidinium lead iodide (FAPbI3) perovskites allows broader absorption of the solar spectrum relative to conventional methylammonium lead iodide (MAPbI3). Because the optoelectronic properties of perovskite films are closely related to film quality, deposition of dense and uniform films is crucial for fabricating high-performance perovskite solar cells (PSCs). We report an approach for depositing high-quality FAPbI3 films, involving FAPbI3 crystallization by the direct intramolecular exchange of dimethylsulfoxide (DMSO) molecules intercalated in PbI2 with formamidinium iodide. This process produces FAPbI3 films with (111)-preferred crystallographic orientation, large-grained dense microstructures, and flat surfaces without residual PbI2. Using films prepared by this technique, we fabricated FAPbI3-based PSCs with maximum power conversion efficiency greater than 20%.