Alex K.-Y. Jen

Bio: Alex K.-Y. Jen is an academic researcher from City University of Hong Kong. The author has contributed to research in topics: Perovskite (structure) & Polymer solar cell. The author has an hindex of 128, co-authored 921 publications receiving 61811 citations. Previous affiliations of Alex K.-Y. Jen include University of Nebraska–Lincoln & Zhejiang California International NanoSystems Institute.

Current Challenges and Prospective Research for Upscaling Hybrid Perovskite Photovoltaics.

Abstract: Organic–inorganic hybrid perovskite photovoltaics (PSCs) are poised to push toward technology translation, but significant challenges complicating commercialization remain. Though J–V hysteresis and ecotoxicity are uniquely imposing issues at scale, CH3NH3PbI3 degradation is by far the sharpest limitation to the technology’s potential market contribution. Herein, we offer a perspective on the practical market potential of PSCs, the nature of fundamental PSC challenges at scale, and an outline of prospective solutions for achieving module scale PSC production tailored to intrinsic advantages of CH3NH3PbI3. Although integrating PSCs into the energy grid is complicated by CH3NH3PbI3 degradation, the ability of PSCs to contribute to consumer electronics and other niche markets like those organic photovoltaics have sought footing in rests primarily upon the technology’s price point. Thus, slot die, roll-to-roll processing has the greatest potential to enable PSC scale-up, and herein, we present a perspective o...

Stabilized wide bandgap perovskite solar cells by tin substitution

Abstract: Wide bandgap MAPb(I1–yBry)3 perovskites show promising potential for application in tandem solar cells. However, unstable photovoltaic performance caused by phase segregation has been observed under illumination when y is above 0.2. Herein, we successfully demonstrate stabilization of the I/Br phase by partially replacing Pb2+ with Sn2+ and verify this stabilization with X-ray diffractometry and transient absorption spectroscopy. The resulting MAPb0.75Sn0.25(I1–yBry)3 perovskite solar cells show stable photovoltaic performance under continuous illumination. Among these cells, the one based on MAPb0.75Sn0.25(I0.4Br0.6)3 perovskite shows the highest efficiency of 12.59% with a bandgap of 1.73 eV, which make it a promising wide bandgap candidate for application in tandem solar cells. The engineering of internal bonding environment by partial Sn substitution is believed to be the main reason for making MAPb0.75Sn0.25(I1–yBry)3 perovskite less vulnerable to phase segregation during the photostriction under ill...

Significant Improved Performance of Photovoltaic Cells Made from a Partially Fluorinated Cyclopentadithiophene/Benzothiadiazole Conjugated Polymer

Abstract: A partially fluorinated low bandgap polymer, poly[2,6-(4,4-bis(2-ethylhexyl)-4H-cyclopenta [2,1-b;3,4-b′]dithiophene)-alt-4,7-(5-fluoro-[2,1,3]-benzothiadiazole)] (PCPDTFBT) was synthesized through a microwave-assisted Stille polymerization. It was found that PCPDTFBT has better π–π stacking in solution than its nonfluorinated analogue, poly[2,6-(4,4-bis(2-ethylhexyl)-4H-cyclopenta[2,1-b;3,4-b′]dithiophene)-alt-4,7-([2,1,3]-benzothiadiazole)] (PCPDTBT), resulting in 2 times higher hole mobility. Power conversion efficiency (PCE) of the device using PCPDTFBT/PC71BM as active layer (5.51%) is much higher than the device using PCPDTBT/PC71BM (2.75%) that was fabricated under the same condition without using any solvent additive to modify the morphology. The significantly enhanced PCE is the result of improved open circuit voltage and short circuit current coming from the lower lying HOMO energy level and the appropriate morphology of PCPDTFBT. In addition, the device with PCPDTFBT/PC71BM could also be proces...

Molecular Engineered Hole-Extraction Materials to Enable Dopant-Free, Efficient p-i-n Perovskite Solar Cells

Abstract: Two hole-extraction materials (HEMs), TPP-OMeTAD and TPP-SMeTAD, have been developed to facilitate the fabrication of efficient p-i-n perovskite solar cells (PVSCs). By replacing the oxygen atom on HEM with sulfur (from TPP-OMeTAD to TPP-SMeTAD), it effectively lowers the highest occupied molecular orbital of the molecule and provides stronger Pb-S interaction with perovskites, leading to efficient charge extraction and surface traps passivation. The TPP-SMeTAD-based PVSCs exhibit both improved photovoltaic performance and reduced hysteresis in p-i-n PVSCs over those based on TPP-OMeTAD. This work not only provides new insights on creating perovskite-HEM heterojunction but also helps in designing new HEM to enable efficient organic–inorganic hybrid PVSCs.

Synthesis and characterization of a novel and highly efficient light‐emitting polymer

Abstract: A polymer (TPD-PPV), incorporating both efficient light-emitting and hole transporting moieties has been synthesized. This polymer also possesses excellent film-forming property, good thermal stability, and high electrochemical reversibility and stability. The HOMO-LUMO energy levels were determined by cyclic voltammetry and UV-Vis measurement. The diode with the structure of ITO/CuPc/TPD-PPV/Al showed high rectification ratio (10 8 ) and low turn-on voltage (4.2 V). A bright green-yellow light-emission was observed in day-light under forward bias.

Electron-hole diffusion lengths exceeding 1 micrometer in an organometal trihalide perovskite absorber.

Abstract: Organic-inorganic perovskites have shown promise as high-performance absorbers in solar cells, first as a coating on a mesoporous metal oxide scaffold and more recently as a solid layer in planar heterojunction architectures. Here, we report transient absorption and photoluminescence-quenching measurements to determine the electron-hole diffusion lengths, diffusion constants, and lifetimes in mixed halide (CH3NH3PbI(3-x)Cl(x)) and triiodide (CH3NH3PbI3) perovskite absorbers. We found that the diffusion lengths are greater than 1 micrometer in the mixed halide perovskite, which is an order of magnitude greater than the absorption depth. In contrast, the triiodide absorber has electron-hole diffusion lengths of ~100 nanometers. These results justify the high efficiency of planar heterojunction perovskite solar cells and identify a critical parameter to optimize for future perovskite absorber development.

Electron-Hole Diffusion Lengths Exceeding 1 Micrometer in an Organometal Trihalide Perovskite Absorber

Abstract: Organic-inorganic perovskites have shown promise as high-performance absorbers in solar cells, first as a coating on a mesoporous metal oxide scaffold and more recently as a solid layer in planar heterojunction architectures. Here, we report transient absorption and photoluminescence-quenching measurements to determine the electron-hole diffusion lengths, diffusion constants, and lifetimes in mixed halide (CH3NH3PbI(3-x)Cl(x)) and triiodide (CH3NH3PbI3) perovskite absorbers. We found that the diffusion lengths are greater than 1 micrometer in the mixed halide perovskite, which is an order of magnitude greater than the absorption depth. In contrast, the triiodide absorber has electron-hole diffusion lengths of ~100 nanometers. These results justify the high efficiency of planar heterojunction perovskite solar cells and identify a critical parameter to optimize for future perovskite absorber development.

Interface engineering of highly efficient perovskite solar cells

Abstract: Advancing perovskite solar cell technologies toward their theoretical power conversion efficiency (PCE) requires delicate control over the carrier dynamics throughout the entire device. By controlling the formation of the perovskite layer and careful choices of other materials, we suppressed carrier recombination in the absorber, facilitated carrier injection into the carrier transport layers, and maintained good carrier extraction at the electrodes. When measured via reverse bias scan, cell PCE is typically boosted to 16.6% on average, with the highest efficiency of ~19.3% in a planar geometry without antireflective coating. The fabrication of our perovskite solar cells was conducted in air and from solution at low temperatures, which should simplify manufacturing of large-area perovskite devices that are inexpensive and perform at high levels.

Aggregation-Induced Emission: Together We Shine, United We Soar!

Abstract: Ju Mei,†,‡,∥ Nelson L. C. Leung,†,‡,∥ Ryan T. K. Kwok,†,‡ Jacky W. Y. Lam,†,‡ and Ben Zhong Tang*,†,‡,§ †HKUST-Shenzhen Research Institute, Hi-Tech Park, Nanshan, Shenzhen 518057, China ‡Department of Chemistry, HKUST Jockey Club Institute for Advanced Study, Institute of Molecular Functional Materials, Division of Biomedical Engineering, State Key Laboratory of Molecular Neuroscience, Division of Life Science, The Hong Kong University of Science and Technology, Clear Water Bay, Kowloon, Hong Kong, China Guangdong Innovative Research Team, SCUT-HKUST Joint Research Laboratory, State Key Laboratory of Luminescent Materials and Devices, South China University of Technology, Guangzhou 510640, China

High-performance photovoltaic perovskite layers fabricated through intramolecular exchange

Abstract: The band gap of formamidinium lead iodide (FAPbI3) perovskites allows broader absorption of the solar spectrum relative to conventional methylammonium lead iodide (MAPbI3). Because the optoelectronic properties of perovskite films are closely related to film quality, deposition of dense and uniform films is crucial for fabricating high-performance perovskite solar cells (PSCs). We report an approach for depositing high-quality FAPbI3 films, involving FAPbI3 crystallization by the direct intramolecular exchange of dimethylsulfoxide (DMSO) molecules intercalated in PbI2 with formamidinium iodide. This process produces FAPbI3 films with (111)-preferred crystallographic orientation, large-grained dense microstructures, and flat surfaces without residual PbI2. Using films prepared by this technique, we fabricated FAPbI3-based PSCs with maximum power conversion efficiency greater than 20%.