scispace - formally typeset
Search or ask a question
Author

Ali Saramat

Bio: Ali Saramat is an academic researcher from California Institute of Technology. The author has contributed to research in topics: Thermoelectric effect & Seebeck coefficient. The author has an hindex of 3, co-authored 3 publications receiving 3267 citations.

Papers
More filters
Journal ArticleDOI
25 Jul 2008-Science
TL;DR: A successful implementation through the use of the thallium impurity levels in lead telluride (PbTe) is reported, which results in a doubling of zT in p-type PbTe to above 1.5 at 773 kelvin.
Abstract: The efficiency of thermoelectric energy converters is limited by the material thermoelectric figure of merit (zT). The recent advances in zT based on nanostructures limiting the phonon heat conduction is nearing a fundamental limit: The thermal conductivity cannot be reduced below the amorphous limit. We explored enhancing the Seebeck coefficient through a distortion of the electronic density of states and report a successful implementation through the use of the thallium impurity levels in lead telluride (PbTe). Such band structure engineering results in a doubling of zT in p-type PbTe to above 1.5 at 773 kelvin. Use of this new physical principle in conjunction with nanostructuring to lower the thermal conductivity could further enhance zT and enable more widespread use of thermoelectric systems.

3,401 citations

Journal ArticleDOI
TL;DR: In this paper, the thermoelectric transport properties of polycrystalline, Ba_(8)Ga_(16−x)Ge_(30+x) were characterized from 300 to 1000 K.
Abstract: The thermoelectric transport properties of polycrystalline, Ba_(8)Ga_(16−x)Ge_(30+x) were characterized from 300 to 1000 K. The carrier density was found to vary precisely with the experimental x as expected from simple electron counting. The experimental data are analyzed within the framework of a single parabolic band model, which is found to accurately describe transport for the compositions of interest for thermoelectric application. The lattice thermal conductivity, calculated with a degeneracy adjusted Lorenz number, does not show a trend with composition and a value of ~1 Wm^(−1) K^(−1) is observed at 300 K. A maximum figure of merit zT = 0.86 is obtained at 950 K, and the optimal doping level for thermoelectric application is predicted to be ~2 × 10^(20) cm^(−3), which corresponds to Ba_(8)Ga_(15.75)Ge_(30.25_ by electron counting. An unexpected transition event is observed near 650 K, which results in a significant increase in the heat capacity.

354 citations

Journal ArticleDOI
19 Jan 2009
TL;DR: In this paper, a thermoelectric performance of polycrystalline Ba8Ga and dGa-type clathrates with trace trace Ge impurity was observed, and the electrical resistivity was stable in measurements up to 1000 K. However, measurements to 1050 K resulted an irreversible increase in carrier concentration while the carrier mobility remained unchanged.
Abstract: Polycrystalline Ba8Ga x Ge46−x exhibits promising thermoelectric performance with the figure of merit ZT close to that of single crystals. Polycrystalline Ba8Ga x Ge46−x is promising for applications, but reproducibility and thermal stability of thermoelectric properties need to be demonstrated. Polycrystalline samples of Ba8+dGa x Ge46−x -type clathrates (15.0 ≤ x ≤ 16.8 with varied nominal Ga content and d = 0 or 0.2) were prepared by direct reaction of the elements, followed by ball milling and hot pressing. Trace Ge impurity was observed (<1.0 wt.%) depending on the synthesis method. The electrical resistivity was stable in measurements up to 1000 K, regardless of Ge impurity. However, measurements to 1050 K resulted in irreversible increase in carrier concentration while the carrier mobility remained unchanged.

13 citations


Cited by
More filters
Journal ArticleDOI
12 Sep 2008-Science
TL;DR: Thermoelectric materials are solid-state energy converters whose combination of thermal, electrical, and semiconductor properties allows them to be used to convert waste heat into electricity or electrical power directly into cooling and heating.
Abstract: Thermoelectric materials are solid-state energy converters whose combination of thermal, electrical, and semiconducting properties allows them to be used to convert waste heat into electricity or electrical power directly into cooling and heating. These materials can be competitive with fluid-based systems, such as two-phase air-conditioning compressors or heat pumps, or used in smaller-scale applications such as in automobile seats, night-vision systems, and electrical-enclosure cooling. More widespread use of thermoelectrics requires not only improving the intrinsic energy-conversion efficiency of the materials but also implementing recent advancements in system architecture. These principles are illustrated with several proven and potential applications of thermoelectrics.

4,700 citations

Journal ArticleDOI
17 Apr 2014-Nature
TL;DR: An unprecedented ZT of 2.6 ± 0.3 at 923 K is reported in SnSe single crystals measured along the b axis of the room-temperature orthorhombic unit cell, which highlights alternative strategies to nanostructuring for achieving high thermoelectric performance.
Abstract: The thermoelectric effect enables direct and reversible conversion between thermal and electrical energy, and provides a viable route for power generation from waste heat The efficiency of thermoelectric materials is dictated by the dimensionless figure of merit, ZT (where Z is the figure of merit and T is absolute temperature), which governs the Carnot efficiency for heat conversion Enhancements above the generally high threshold value of 25 have important implications for commercial deployment, especially for compounds free of Pb and Te Here we report an unprecedented ZT of 26 ± 03 at 923 K, realized in SnSe single crystals measured along the b axis of the room-temperature orthorhombic unit cell This material also shows a high ZT of 23 ± 03 along the c axis but a significantly reduced ZT of 08 ± 02 along the a axis We attribute the remarkably high ZT along the b axis to the intrinsically ultralow lattice thermal conductivity in SnSe The layered structure of SnSe derives from a distorted rock-salt structure, and features anomalously high Gruneisen parameters, which reflect the anharmonic and anisotropic bonding We attribute the exceptionally low lattice thermal conductivity (023 ± 003 W m(-1) K(-1) at 973 K) in SnSe to the anharmonicity These findings highlight alternative strategies to nanostructuring for achieving high thermoelectric performance

3,823 citations

Journal ArticleDOI
20 Sep 2012-Nature
TL;DR: It is shown that heat-carrying phonons with long mean free paths can be scattered by controlling and fine-tuning the mesoscale architecture of nanostructured thermoelectric materials, and an increase in ZT beyond the threshold of 2 highlights the role of, and need for, multiscale hierarchical architecture in controlling phonon scattering in bulk thermoeLECTrics.
Abstract: Controlling the structure of thermoelectric materials on all length scales (atomic, nanoscale and mesoscale) relevant for phonon scattering makes it possible to increase the dimensionless figure of merit to more than two, which could allow for the recovery of a significant fraction of waste heat with which to produce electricity.

3,670 citations

Journal ArticleDOI
05 May 2011-Nature
TL;DR: It is demonstrated that it is possible to direct the convergence of many valleys in a bulk material by tuning the doping and composition, leading to an extraordinary zT value of 1.8 at about 850 kelvin.
Abstract: Thermoelectric generators, which directly convert heat into electricity, have long been relegated to use in space-based or other niche applications, but are now being actively considered for a variety of practical waste heat recovery systems—such as the conversion of car exhaust heat into electricity. Although these devices can be very reliable and compact, the thermoelectric materials themselves are relatively inefficient: to facilitate widespread application, it will be desirable to identify or develop materials that have an intensive thermoelectric materials figure of merit, zT, above 1.5 (ref. 1). Many different concepts have been used in the search for new materials with high thermoelectric efficiency, such as the use of nanostructuring to reduce phonon thermal conductivity, which has led to the investigation of a variety of complex material systems. In this vein, it is well known, that a high valley degeneracy (typically ≤6 for known thermoelectrics) in the electronic bands is conducive to high zT, and this in turn has stimulated attempts to engineer such degeneracy by adopting low-dimensional nanostructures. Here we demonstrate that it is possible to direct the convergence of many valleys in a bulk material by tuning the doping and composition. By this route, we achieve a convergence of at least 12 valleys in doped PbTe_(1) − _(x)Se_(x) alloys, leading to an extraordinary zT value of 1.8 at about 850 kelvin. Band engineering to converge the valence (or conduction) bands to achieve high valley degeneracy should be a general strategy in the search for and improvement of bulk thermoelectric materials, because it simultaneously leads to a high Seebeck coefficient and high electrical conductivity.

2,964 citations

Journal ArticleDOI
TL;DR: The most promising bulk materials with emphasis on results from the last decade are described and the new opportunities for enhanced performance bulk nanostructured composite materials are examined and a look into the not so distant future is attempted.
Abstract: Herein we cover the key concepts in the field of thermoelectric materials research, present the current understanding, and show the latest developments. Current research is aimed at increasing the thermoelectric figure of merit (ZT) by maximizing the power factor and/or minimizing the thermal conductivity. Attempts at maximizing the power factor include the development of new materials, optimization of existing materials by doping, and the exploration of nanoscale materials. The minimization of the thermal conductivity can come through solid-solution alloying, use of materials with intrinsically low thermal conductivity, and nanostructuring. Herein we describe the most promising bulk materials with emphasis on results from the last decade. Single-phase bulk materials are discussed in terms of chemistry, crystal structure, physical properties, and optimization of thermoelectric performance. The new opportunities for enhanced performance bulk nanostructured composite materials are examined and a look into the not so distant future is attempted.

1,951 citations