Amitava Gupta

Bio: Amitava Gupta is an academic researcher from Jadavpur University. The author has contributed to research in topics: PID controller & Control theory. The author has an hindex of 18, co-authored 88 publications receiving 1585 citations.

Tuning of an optimal fuzzy PID controller with stochastic algorithms for networked control systems with random time delay.

Abstract: An optimal PID and an optimal fuzzy PID have been tuned by minimizing the Integral of Time multiplied Absolute Error (ITAE) and squared controller output for a networked control system (NCS) The tuning is attempted for a higher order and a time delay system using two stochastic algorithms viz the Genetic Algorithm (GA) and two variants of Particle Swarm Optimization (PSO) and the closed loop performances are compared The paper shows that random variation in network delay can be handled efficiently with fuzzy logic based PID controllers over conventional PID controllers

On the selection of tuning methodology of FOPID controllers for the control of higher order processes.

Abstract: In this paper, a comparative study is done on the time and frequency domain tuning strategies for fractional order (FO) PID controllers to handle higher order processes. A new fractional order template for reduced parameter modelling of stable minimum/non-minimum phase higher order processes is introduced and its advantage in frequency domain tuning of FOPID controllers is also presented. The time domain optimal tuning of FOPID controllers have also been carried out to handle these higher order processes by performing optimization with various integral performance indices. The paper highlights on the practical control system implementation issues like flexibility of online autotuning, reduced control signal and actuator size, capability of measurement noise filtration, load disturbance suppression, robustness against parameter uncertainties etc. in light of the above tuning methodologies.

Fractional Order Modeling of a PHWR Under Step-Back Condition and Control of Its Global Power With a Robust ${\rm PI}^{\lambda} {\rm D} ^{\mu}$ Controller

Abstract: Bulk reduction of reactor power within a small finite time interval under abnormal conditions is referred to as step-back. In this paper, a 500 MWe Canadian Deuterium Uranium (CANDU) type Pressurized Heavy Water Reactor (PHWR) is modeled using few variants of Least Square Estimator (LSE) from practical test data under a control rod drop scenario in order to design a control system to achieve a dead-beat response during a stepped reduction of its global power. A new fractional order (FO) model reduction technique is attempted which increases the parametric robustness of the control loop due to lesser modeling error and ensures iso-damped closed loop response with a PIλDμ or FOPID controller. Such a controller can, therefore, be used to achieve active step-back under varying load conditions for which the system dynamics change significantly. For closed loop active control of the reduced FO reactor models, the PIλDμ controller is shown to perform better than the classical integer order PID controllers and present operating Reactor Regulating System (RRS) due to its robustness against shift in system parameters.

RMST: Reliable Data Transport in Sensor Networks

Abstract: Appearing in 1st IEEE International Workshop on Sensor Net Protocols and Applications (SNPA). Anchorage, Alaska, USA. May 11, 2003. RMST: Reliable Data Transport in Sensor Networks Fred Stann, John Heidemann Abstract – Reliable data transport in wireless sensor networks is a multifaceted problem influenced by the physical, MAC, network, and transport layers. Because sensor networks are subject to strict resource constraints and are deployed by single organizations, they encourage revisiting traditional layering and are less bound by standardized placement of services such as reliability. This paper presents analysis and experiments resulting in specific recommendations for implementing reliable data transport in sensor nets. To explore reliability at the transport layer, we present RMST (Reliable Multi- Segment Transport), a new transport layer for Directed Diffusion. RMST provides guaranteed delivery and fragmentation/reassembly for applications that require them. RMST is a selective NACK-based protocol that can be configured for in-network caching and repair. Second, these energy constraints, plus relatively low wireless bandwidths, make in-network processing both feasible and desirable [3]. Third, because nodes in sensor networks are usually collaborating towards a common task, rather than representing independent users, optimization of the shared network focuses on throughput rather than fairness. Finally, because sensor networks are often deployed by a single organization with inexpensive hardware, there is less need for interoperability with existing standards. For all of these reasons, sensor networks provide an environment that encourages rethinking the structure of traditional communications protocols. The main contribution is an evaluation of the placement of reliability for data transport at different levels of the protocol stack. We consider implementing reliability in the MAC, transport layer, application, and combinations of these. We conclude that reliability is important at the MAC layer and the transport layer. MAC-level reliability is important not just to provide hop-by-hop error recovery for the transport layer, but also because it is needed for route discovery and maintenance. (This conclusion differs from previous studies in reliability for sensor nets that did not simulate routing. [4]) Second, we have developed RMST (Reliable Multi-Segment Transport), a new transport layer, in order to understand the role of in- network processing for reliable data transfer. RMST benefits from diffusion routing, adding minimal additional control traffic. RMST guarantees delivery, even when multiple hops exhibit very high error rates. 1 Introduction Wireless sensor networks provide an economical, fully distributed, sensing and computing solution for environments where conventional networks are impractical. This paper explores the design decisions related to providing reliable data transport in sensor nets. The reliable data transport problem in sensor nets is multi-faceted. The emphasis on energy conservation in sensor nets implies that poor paths should not be artificially bolstered via mechanisms such as MAC layer ARQ during route discovery and path selection [1]. Path maintenance, on the other hand, benefits from well- engineered recovery either at the MAC layer or the transport layer, or both. Recovery should not be costly however, since many applications in sensor nets are impervious to occasional packet loss, relying on the regular delivery of coarse-grained event descriptions. Other applications require loss detection and repair. These aspects of reliable data transport include the provision of guaranteed delivery and fragmentation/ reassembly of data entities larger than the network MTU. Sensor networks have different constraints than traditional wired nets. First, energy constraints are paramount in sensor networks since nodes can often not be recharged, so any wasted energy shortens their useful lifetime [2]. This work was supported by DARPA under grant DABT63-99-1-0011 as part of the SCAADS project, and was also made possible in part due to support from Intel Corporation and Xerox Corporation. Fred Stann and John Heidemann are with USC/Information Sciences Institute, 4676 Admiralty Way, Marina Del Rey, CA, USA E-mail: fstann@usc.edu, johnh@isi.edu. 2 Architectural Choices There are a number of key areas to consider when engineering reliability for sensor nets. Many current sensor networks exhibit high loss rates compared to wired networks (2% to 30% to immediate neighbors)[1,5,6]. While error detection and correction at the physical layer are important, approaches at the MAC layer and higher adapt well to the very wide range of loss rates seen in sensor networks and are the focus of this paper. MAC layer protocols can ameliorate PHY layer unreliability, and transport layers can guarantee delivery. An important question for this paper is the trade off between implementation of reliability at the MAC layer (i.e. hop to hop) vs. the Transport layer, which has traditionally been concerned with end-to-end reliability. Because sensor net applications are distributed, we also considered implementing reliability at the application layer. Our goal is to minimize the cost of repair in terms of transmission.

Energy and exergy analyses of thermal power plants: A review

Abstract: The energy supply to demand narrowing down day by day around the world, the growing demand of power has made the power plants of scientific interest, but most of the power plants are designed by the energetic performance criteria based on first law of thermodynamics only. The real useful energy loss cannot be justified by the fist law of thermodynamics, because it does not differentiate between the quality and quantity of energy. The present study deals with the comparison of energy and exergy analyses of thermal power plants stimulated by coal and gas. This article provides a detailed review of different studies on thermal power plants over the years. This review would also throw light on the scope for further research and recommendations for improvement in the existing thermal power plants.