André Pineau

Bio: André Pineau is an academic researcher from Mines ParisTech. The author has contributed to research in topics: Fracture mechanics & Creep. The author has an hindex of 58, co-authored 277 publications receiving 12074 citations. Previous affiliations of André Pineau include École Normale Supérieure & Academy of Engineering.

A Local Criterion for Cleavage Fracture of a Nuclear Pressure Vessel Steel

Abstract: Experiments were performed on three heats of A508 class 3 steel in order to determine the mechanical conditions for cleavage fracture. These tests were carried out on various geometries including 4-point bend specimens and axisymmetric notched tensile bars with different notch radii which have been modelized using the finite element method. In one heat, the temperature range investigated was from 77 K to 233 K. It is shown that the cleavage resistance is increased by tensile straining. Moreover, the probability of fracture obeys the Weibull statistical distribution. All the results can be accounted for in terms of a local criterion based on Weibull theory and which takes into account the effect of plastic strain. In this criterion, the parameters which were experimentally determined are found to be temperature independent over the range 77 K to 170 K. The applicability of the approach proposed for cleavage fracture at the crack tip is also examined. It is shown that the experimental results published in the literature giving the variation of fracture toughness with temperature can be explained by the proposed criterion which predicts reasonably well both the scatter in the experimental results and theKICtemperature dependence.

Morphology of y’ and y” precipitates and thermal stability of inconel 718 type alloys

Abstract: The precipitation of the γ’ (Ll2) and γ" (DO22) phases has been studied in four alloys Fe-Ni-Cr-Ti-Al-Nb containing a higher Ti + Al/Nb ratio than that of the INCONEL 718 alloy. For these alloys, the precipitation microstructure varies rapidly with aging temperature and composition. Bct γ"particles have always been found to precipitate on γ’ phase. Moreover, by aging three alloys above a critical temperature, a “compact ntorphology” has been observed: cube-shaped γ’ particles coated on their six faces with a shell of γ" precipitate. This microstructure has proved to be very stable on prolonged aging. A thermal stability better than that encountered in nominal INCONEL 718 alloy can thus be achieved. The influence of composition and aging temperature on the conditions that bring about this “compact morphology” has been investigated. A minimal Ti + Al/Nb ratio between 0.9 and 1 has been determined, allowing the “compact morphology” to be obtained.

Martensitic transformations induced by plastic deformation in the Fe-Ni-Cr-C system

Abstract: Martensitic transformations induced by plastic deformation are studied comparatively in various alloys of three types: Fe-30 pct Ni, Fe-20 pct Ni-7 pct Cr, and Fe-16 pet Cr-13 pct Ni, with carbon content up to 0.3 pct. For all these alloys the tensile properties vary rapidly with temperature, but there are large differences in the value of the temperature rangeM s toM d, which strongly increases with substitution of chromium for nickel or with carbon addition. Using the node method, it is found that the intrinsic stacking fault energy in the austenite drastically increases with temperature in all the chromium-bearing alloys investigated. This variation is consistent with the observed influence of temperature on the appearance of twinning or e martensite during plastic deformation. Very different α’ martensite morphologies can result from spontaneous and plastic deformation induced transformations, especially in Fe-20 pct Ni-7 pct Cr-type alloys where platelike and lath martensites are respectively observed. As in the case of e martensite, the nucleation process is analyzed as a deformation mode of the material, using a dislocation model. It is then possible to account for the morphology of plastic deformation induced α’ martensite in both Fe-20 pct Ni-7 pct Cr and Fe-16 pct Cr-13 pct Ni types alloys and for the largeM s toM d range in these alloys.

A fracture-resistant high-entropy alloy for cryogenic applications

Abstract: High-entropy alloys are equiatomic, multi-element systems that can crystallize as a single phase, despite containing multiple elements with different crystal structures. A rationale for this is that the configurational entropy contribution to the total free energy in alloys with five or more major elements may stabilize the solid-solution state relative to multiphase microstructures. We examined a five-element high-entropy alloy, CrMnFeCoNi, which forms a single-phase face-centered cubic solid solution, and found it to have exceptional damage tolerance with tensile strengths above 1 GPa and fracture toughness values exceeding 200 MPa·m(1/2). Furthermore, its mechanical properties actually improve at cryogenic temperatures; we attribute this to a transition from planar-slip dislocation activity at room temperature to deformation by mechanical nanotwinning with decreasing temperature, which results in continuous steady strain hardening.

Nickel-Based Superalloys for Advanced Turbine Engines: Chemistry, Microstructure and Properties

Abstract: The chemical, physical, and mechanical characteristics of nickel-based superalloys are reviewed with emphasis on the use of this class of materials within turbine engines. The role of major and minor alloying additions in multicomponent commercial cast and wrought superalloys is discussed. Microstructural stability and phases observed during processing and in subsequent elevated-temperature service are summarized. Processing paths and recent advances in processing are addressed. Mechanical properties and deformation mechanisms are reviewed, including tensile properties, creep, fatigue, and cyclic crack growth. I. Introduction N ICKEL-BASED superalloys are an unusual class of metallic materials with an exceptional combination of hightemperature strength, toughness, and resistance to degradation in corrosive or oxidizing environments. These materials are widely used in aircraft and power-generation turbines, rocket engines, and other challenging environments, including nuclear power and chemical processing plants. Intensive alloy and process development activities during the past few decades have resulted in alloys that can tolerate average temperatures of 1050 ◦ C with occasional excursions (or local hot spots near airfoil tips) to temperatures as high as 1200 ◦ C, 1 which is approximately 90% of the melting point of the material. The underlying aspects of microstructure and composition that result in these exceptional properties are briefly reviewed here. Major classes of superalloys that are utilized in gas-turbine engines and the corresponding processes for their production are outlined along with characteristic mechanical and physical properties.

Recent developments in stainless steels

Abstract: This article presents an overview of the developments in stainless steels made since the 1990s. Some of the new applications that involve the use of stainless steel are also introduced. A brief introduction to the various classes of stainless steels, their precipitate phases and the status quo of their production around the globe is given first. The advances in a variety of subject areas that have been made recently will then be presented. These recent advances include (1) new findings on the various precipitate phases (the new J phase, new orientation relationships, new phase diagram for the Fe–Cr system, etc.); (2) new suggestions for the prevention/mitigation of the different problems and new methods for their detection/measurement and (3) new techniques for surface/bulk property enhancement (such as laser shot peening, grain boundary engineering and grain refinement). Recent developments in topics like phase prediction, stacking fault energy, superplasticity, metadynamic recrystallisation and the calculation of mechanical properties are introduced, too. In the end of this article, several new applications that involve the use of stainless steels are presented. Some of these are the use of austenitic stainless steels for signature authentication (magnetic recording), the utilisation of the cryogenic magnetic transition of the sigma phase for hot spot detection (the Sigmaplugs), the new Pt-enhanced radiopaque stainless steel (PERSS) coronary stents and stainless steel stents that may be used for magnetic drug targeting. Besides recent developments in conventional stainless steels, those in the high-nitrogen, low-Ni (or Ni-free) varieties are also introduced. These recent developments include new methods for attaining very high nitrogen contents, new guidelines for alloy design, the merits/demerits associated with high nitrogen contents, etc.