Anthony J. Giordano

Bio: Anthony J. Giordano is an academic researcher from Georgia Institute of Technology. The author has contributed to research in topics: Geography & Indium tin oxide. The author has an hindex of 19, co-authored 29 publications receiving 2742 citations. Previous affiliations of Anthony J. Giordano include Georgia Tech Research Institute.

A Universal Method to Produce Low―Work Function Electrodes for Organic Electronics

Abstract: Organic and printed electronics technologies require conductors with a work function that is sufficiently low to facilitate the transport of electrons in and out of various optoelectronic devices. We show that surface modifiers based on polymers containing simple aliphatic amine groups substantially reduce the work function of conductors including metals, transparent conductive metal oxides, conducting polymers, and graphene. The reduction arises from physisorption of the neutral polymer, which turns the modified conductors into efficient electron-selective electrodes in organic optoelectronic devices. These polymer surface modifiers are processed in air from solution, providing an appealing alternative to chemically reactive low–work function metals. Their use can pave the way to simplified manufacturing of low-cost and large-area organic electronic technologies.

Phosphonic Acids for Interfacial Engineering of Transparent Conductive Oxides

Abstract: Transparent conducting oxides (TCOs), such as indium tin oxide and zinc oxide, play an important role as electrode materials in organic-semiconductor devices. The properties of the inorganic–organic interface—the offset between the TCO Fermi level and the relevant transport level, the extent to which the organic semiconductor can wet the oxide surface, and the influence of the surface on semiconductor morphology—significantly affect device performance. This review surveys the literature on TCO modification with phosphonic acids (PAs), which has increasingly been used to engineer these interfacial properties. The first part outlines the relevance of TCO surface modification to organic electronics, surveys methods for the synthesis of PAs, discusses the modes by which they can bind to TCO surfaces, and compares PAs to alternative organic surface modifiers. The next section discusses methods of PA monolayer deposition, the kinetics of monolayer formation, and structural evidence regarding molecular orientati...

Investigating the Influence of Interfacial Contact Properties on Open Circuit Voltages in Organic Photovoltaic Performance: Work Function Versus Selectivity

Abstract: The role of work function and thermodynamic selectivity of hole collecting contacts on the origin of open circuit voltage (VOC) in bulk heterojunction organic photovoltaics is examined for poly(N-9′-heptadecanyl-2,7-carbazole-alt-5,5-(4′,7′-di-2-thienyl-2′,1′,3′-benzothiadiazole) (PCDTBT) and [6,6]-phenyl-C71 butyric acid methyl ester (PC71BM) solar cells. In the absence of a charge selective, electron blocking contact, systematic variation of the work function of the contact directly dictates the VOC, as defined by the energetic separation between the relative Fermi levels for holes and electrons, with little change in the observed dark saturation current, J0. Improving the charge selectivity of the contact through an increased barrier to electron injection from the fullerene in the blend into the hole contact results in a decreased reverse saturation current (decreased J0 and increased shunt resistance, RSH) and improved VOC. Based on these observations, we provide a set of contact design criteria for tuning the VOC in bulk heterojunction organic photovoltaics.

Characterization of phosphonic acid binding to zinc oxide

Abstract: Radio Frequency (RF) sputter-deposited zinc oxide (ZnO) films have been modified with alkylphosphonic acids in order to study both the binding of the phosphonic acid (PA) group to the ZnO surface and the packing of the alkyl chain. The characterization of these PA-modified ZnO substrates by X-ray photoelectron spectroscopy (XPS), infrared reflection-absorption spectroscopy (IRRAS), atomic force microscopy (AFM) and contact angle measurements is presented herein. The surface modification procedure is straightforward and was adapted from earlier work. XPS analysis shows that oxygen plasma (OP) treatment creates reactive oxygen species on the surface of ZnO, allowing for a more robust binding of PAs to the ZnO surface. IRRAS analysis indicates that octadecylphosphonic acid binds to the ZnO surface in a predominantly tridentate fashion, forming dense, well-packed monolayers with alkyl chains in a fully anti-conformation. AFM and contact angle measurements indicate good surface coverage of the PAs with little to no multilayer formation.

Stability of inverted organic solar cells with ZnO contact layers deposited from precursor solutions

Abstract: We report on investigations of the stability of inverted organic solar cells with ZnO electron collecting interlayer that are solution-processed from zinc acetate (ZnAc) or diethylzinc (deZn) precursors. Characterization of the respective solar cells suggests that the two materials initially function similarly in devices, however, we find that devices with ZnO from the deZn precursor are more stable under long-term illumination and load than devices with ZnO from the ZnAc precursor. A dipolar phosphonic acid that reduces the ZnO work function also improved device performance and stability when compared with unmodified ZnAc-based ZnO, but was problematic for deZn-based ZnO. The long-term device degradation analyses shows that the improved devices had increased and significantly more stable open-circuit voltage and fill factor characteristics. Chemical analyses suggests that defects in the ZnO films, most likely interstitial zinc, may be responsible for the observed disparities in stability within organic solar cells.

Interface engineering of highly efficient perovskite solar cells

Abstract: Advancing perovskite solar cell technologies toward their theoretical power conversion efficiency (PCE) requires delicate control over the carrier dynamics throughout the entire device. By controlling the formation of the perovskite layer and careful choices of other materials, we suppressed carrier recombination in the absorber, facilitated carrier injection into the carrier transport layers, and maintained good carrier extraction at the electrodes. When measured via reverse bias scan, cell PCE is typically boosted to 16.6% on average, with the highest efficiency of ~19.3% in a planar geometry without antireflective coating. The fabrication of our perovskite solar cells was conducted in air and from solution at low temperatures, which should simplify manufacturing of large-area perovskite devices that are inexpensive and perform at high levels.

An electron acceptor challenging fullerenes for efficient polymer solar cells.

Abstract: A novel non-fullerene electron acceptor (ITIC) that overcomes some of the shortcomings of fullerene acceptors, for example, weak absorption in the visible spectral region and limited energy-level variability, is designed and synthesized. Fullerene-free polymer solar cells (PSCs) based on the ITIC acceptor are demonstrated to exhibit power conversion effi ciencies of up to 6.8%, a record for fullerene-free PSCs.

Perovskite light-emitting diodes based on solution-processed self-organized multiple quantum wells

Abstract: Perovskite quantum wells yield highly efficient LEDs spanning the visible and near-infrared.

Perovskite light-emitting diodes based on spontaneously formed submicrometre-scale structures

Abstract: Light-emitting diodes (LEDs), which convert electricity to light, are widely used in modern society—for example, in lighting, flat-panel displays, medical devices and many other situations. Generally, the efficiency of LEDs is limited by nonradiative recombination (whereby charge carriers recombine without releasing photons) and light trapping1–3. In planar LEDs, such as organic LEDs, around 70 to 80 per cent of the light generated from the emitters is trapped in the device4,5, leaving considerable opportunity for improvements in efficiency. Many methods, including the use of diffraction gratings, low-index grids and buckling patterns, have been used to extract the light trapped in LEDs6–9. However, these methods usually involve complicated fabrication processes and can distort the light-output spectrum and directionality6,7. Here we demonstrate efficient and high-brightness electroluminescence from solution-processed perovskites that spontaneously form submicrometre-scale structures, which can efficiently extract light from the device and retain wavelength- and viewing-angle-independent electroluminescence. These perovskites are formed simply by introducing amino-acid additives into the perovskite precursor solutions. Moreover, the additives can effectively passivate perovskite surface defects and reduce nonradiative recombination. Perovskite LEDs with a peak external quantum efficiency of 20.7 per cent (at a current density of 18 milliamperes per square centimetre) and an energy-conversion efficiency of 12 per cent (at a high current density of 100 milliamperes per square centimetre) can be achieved—values that approach those of the best-performing organic LEDs. The formation of submicrometre-scale structure in perovskite light-emitting diodes can raise their external quantum efficiency beyond 20%, suggesting the possibility of both high efficiency and high brightness.