B. Axelrod

Bio: B. Axelrod is an academic researcher from Holon Institute of Technology. The author has contributed to research in topics: Boost converter & Ćuk converter. The author has an hindex of 20, co-authored 40 publications receiving 2235 citations. Previous affiliations of B. Axelrod include Tel Aviv University.

Switched-Capacitor/Switched-Inductor Structures for Getting Transformerless Hybrid DC–DC PWM Converters

Abstract: A few simple switching structures, formed by either two capacitors and two-three diodes (C-switching), or two inductors and two-three diodes (L-switching) are proposed. These structures can be of two types: ldquostep-downrdquo and ldquostep-up.rdquo These blocks are inserted in classical converters: buck, boost, buck-boost, Cuk, Zeta, Sepic. The ldquostep-downrdquo C- or L-switching structures can be combined with the buck, buck-boost, Cuk, Zeta, Sepic converters in order to get a step-down function. When the active switch of the converter is on, the inductors in the L-switching blocks are charged in series or the capacitors in the C-switching blocks are discharged in parallel. When the active switch is off, the inductors in the L-switching blocks are discharged in parallel or the capacitors in the C-switching blocks are charged in series. The ldquostep-uprdquo C- or L-switching structures are combined with the boost, buck-boost, Cuk, Zeta, Sepic converters, to get a step-up function. The steady-state analysis of the new hybrid converters allows for determing their DC line-to-output voltage ratio. The gain formula shows that the hybrid converters are able to reduce/increase the line voltage more times than the original, classical converters. The proposed hybrid converters contain the same number of elements as the quadratic converters. Their performances (DC gain, voltage and current stresses on the active switch and diodes, currents through the inductors) are compared to those of the available quadratic converters. The superiority of the new, hybrid converters is mainly based on less energy in the magnetic field, leading to saving in the size and cost of the inductors, and less current stresses in the switching elements, leading to smaller conduction losses. Experimental results confirm the theoretical analysis.

Switched-coupled inductor cell for DC-DC converters with very large conversion ratio

Abstract: By replacing the inductor in basic converters by a coupled-inductor, and adding one diode, new converters with a small count of elements and a high conversion ratio are obtained. The additional diode helps to circulate the leakage inductance energy to the load in a non-oscillatory manner. This diode conducts for a short period of time. The transistor turns on/off with soft-switching. The diodes turn on with zero-voltage switching and turn off with zero-current-switching, their reverse-recovery problem is alleviated. A switching-coupled inductor boost converter is studied in detail, and a family of DC-DC converters (boost, buck-boost, C-uk, Sepic, Zeta) based on the new switching cell is then presented. The dependence of the voltage gain on the magnetic-coupling coefficient and turns ratio of the coupled inductor is studied. The influence of the load value on the voltage conversion ratio is discussed based on an exact analysis, which avoids assumptions of ideal elements. Computer simulation and experimental results confirmed the theoretical expectations.

Transformerless DC-DC converters with a very high DC line-to-load voltage ratio

Abstract: By splitting the output capacitor of a basic boost converter, and combining the resulting capacitors with the main switch in the form of a switched-capacitor circuit, a new step-up structure is realized. Without using a transformer, a high line-to-load DC voltage ratio is obtained. An output filter is added as usual in boost converters for getting a free-ripple output. The circuit compares favorably with a quadratic boost converter as regarding the count of devices and efficiency, even if it presents a lower DC gain. A DC analysis of the novel converter is presented. Experimental and simulation results confirm the theoretical expectations. By increasing the number of capacitors in the switched-capacitor circuit, higher gains are obtained. Versatility, high voltage gain and a good transient response are the features of the proposed converter.

A cascade boost-switched-capacitor-converter - two level inverter with an optimized multilevel output waveform

Abstract: Two structures, a switched-capacitor (SC)-based boost converter and a two-level inverter, are connected in cascade. The dc multilevel voltage of the first stage becomes the input voltage of the classical inverter, resulting in a staircase waveform for the inverter output voltage. Such a multilevel waveform is close to a sinusoid; its harmonics content can be reduced by multiplying the stage number of the SC converter. The output low-pass filter, customary after a two-level inverter, becomes obsolete, resulting in a small size of the system, as the SC circuit can be miniaturized. Both stages are operated at a high switching frequency, resulting in a high-frequency inverter output, as required by some industrial applications. A Fourier analysis of the output waveform is performed. The design is optimized with reference to the nominal duty-cycle for obtaining the minimum total harmonic distortion. Simulations and experiments on two prototypes, one with a five-level output and one with a seven-level output, confirm the theoretical analysis.

High step-up DC–DC converter based on the switched-coupled-inductor boost converter and diode-capacitor multiplier: steady state and dynamics

Abstract: In this study a new scheme of a step-up converter with very high voltage gain is proposed. The scheme is based on a natural combination of the switched-coupled-inductor boost converter and the diode-capacitor multiplier. The study proposes a special scheme of their mutual use for attaining very high voltage gain. An important advantage of the proposed circuit is the avoidance of the current spikes through the transistor and diodes because of the leakage inductance of the coupled inductors. The scheme provides soft commutation of the switch and the diodes. The study analyses the modes of operation and obtains the basic fundamental relations in steady state; an expression for voltage stress across the switch is derived. A new method for dynamic analysis is proposed. The corresponding analytical expressions and curves of the transient behaviour are also obtained. Modelling of the proposed structure and the experimental results are in full agreement regarding the expected efficiency and correctness of the theoretical analysis. A 100 W laboratory prototype was built and verified.

Step-Up DC–DC Converters: A Comprehensive Review of Voltage-Boosting Techniques, Topologies, and Applications

Abstract: DC–DC converters with voltage boost capability are widely used in a large number of power conversion applications, from fraction-of-volt to tens of thousands of volts at power levels from milliwatts to megawatts. The literature has reported on various voltage-boosting techniques, in which fundamental energy storing elements (inductors and capacitors) and/or transformers in conjunction with switch(es) and diode(s) are utilized in the circuit. These techniques include switched capacitor (charge pump), voltage multiplier, switched inductor/voltage lift, magnetic coupling, and multistage/-level, and each has its own merits and demerits depending on application, in terms of cost, complexity, power density, reliability, and efficiency. To meet the growing demand for such applications, new power converter topologies that use the above voltage-boosting techniques, as well as some active and passive components, are continuously being proposed. The permutations and combinations of the various voltage-boosting techniques with additional components in a circuit allow for numerous new topologies and configurations, which are often confusing and difficult to follow. Therefore, to present a clear picture on the general law and framework of the development of next-generation step-up dc–dc converters, this paper aims to comprehensively review and classify various step-up dc–dc converters based on their characteristics and voltage-boosting techniques. In addition, the advantages and disadvantages of these voltage-boosting techniques and associated converters are discussed in detail. Finally, broad applications of dc–dc converters are presented and summarized with comparative study of different voltage-boosting techniques.

Switched-Capacitor/Switched-Inductor Structures for Getting Transformerless Hybrid DC–DC PWM Converters

Abstract: A few simple switching structures, formed by either two capacitors and two-three diodes (C-switching), or two inductors and two-three diodes (L-switching) are proposed. These structures can be of two types: ldquostep-downrdquo and ldquostep-up.rdquo These blocks are inserted in classical converters: buck, boost, buck-boost, Cuk, Zeta, Sepic. The ldquostep-downrdquo C- or L-switching structures can be combined with the buck, buck-boost, Cuk, Zeta, Sepic converters in order to get a step-down function. When the active switch of the converter is on, the inductors in the L-switching blocks are charged in series or the capacitors in the C-switching blocks are discharged in parallel. When the active switch is off, the inductors in the L-switching blocks are discharged in parallel or the capacitors in the C-switching blocks are charged in series. The ldquostep-uprdquo C- or L-switching structures are combined with the boost, buck-boost, Cuk, Zeta, Sepic converters, to get a step-up function. The steady-state analysis of the new hybrid converters allows for determing their DC line-to-output voltage ratio. The gain formula shows that the hybrid converters are able to reduce/increase the line voltage more times than the original, classical converters. The proposed hybrid converters contain the same number of elements as the quadratic converters. Their performances (DC gain, voltage and current stresses on the active switch and diodes, currents through the inductors) are compared to those of the available quadratic converters. The superiority of the new, hybrid converters is mainly based on less energy in the magnetic field, leading to saving in the size and cost of the inductors, and less current stresses in the switching elements, leading to smaller conduction losses. Experimental results confirm the theoretical analysis.

Voltage Multiplier Cells Applied to Non-Isolated DC–DC Converters

Abstract: This paper introduces the use of the voltage multiplier technique applied to the classical non-isolated dc-dc converters in order to obtain high step-up static gain, reduction of the maximum switch voltage, zero current switching turn-on. The diodes reverse recovery current problem is minimized and the voltage multiplier also operates as a regenerative clamping circuit, reducing the problems with layout and the EMI generation. These characteristics allows the operation with high static again and high efficiency, making possible to design a compact circuit for applications where the isolation is not required. The operation principle, the design procedure and practical results obtained from the implemented prototypes are presented for the single-phase and multiphase dc-dc converters. A boost converter was tested with the single-phase technique, for an application requiring an output power of 100 W, operating with 12 V input voltage and 100 V output voltage, obtaining efficiency equal to 93%. The multiphase technique was tested with a boost interleaved converter operating with an output power equal to 400 W, 24 V input voltage and 400 V output voltage, obtaining efficiency equal to 95%.

Transformerless DC–DC Converters With High Step-Up Voltage Gain

Abstract: Conventional dc-dc boost converters are unable to provide high step-up voltage gains due to the effect of power switches, rectifier diodes, and the equivalent series resistance of inductors and capacitors. This paper proposes transformerless dc-dc converters to achieve high step-up voltage gain without an extremely high duty ratio. In the proposed converters, two inductors with the same level of inductance are charged in parallel during the switch-on period and are discharged in series during the switch-off period. The structures of the proposed converters are very simple. Only one power stage is used. Moreover, the steady-state analyses of voltage gains and boundary operating conditions are discussed in detail. Finally, a prototype circuit is implemented in the laboratory to verify the performance.