Author

# B Pinkus

Bio: B Pinkus is an academic researcher. The author has an hindex of 1, co-authored 1 publications receiving 766 citations.

##### Papers

More filters

##### Cited by

More filters

••

TL;DR: In this article, a simulation of flow between rough surfaces was done using a fractal model of surface topography and the hydraulic aperture was compared to the mean separation of the surfaces.

Abstract: Fluid flow through rock joints is commonly described by the parallel plate model where the volume flow rate varies as the cube of the joint aperture. However, deviations from this model are expected because real joint surfaces are rough and contact each other at discrete points. To examine this problem further, a computer simulation of flow between rough surfaces was done. Realistic rough surfaces were generated numerically using a fractal model of surface topography. Pairs of these surfaces were placed together to form a “joint” with a random aperture distribution. Reynolds equation, which describes laminar flow between slightly nonplanar and nonparallel surfaces, was solved on the two-dimensional aperture mesh by the finite-difference method. The solution is the local volume flow rate through the joint. This solution was used directly in the cubic law to get the so-called “hydraulic aperture.” For various surface roughnesses (fractal dimensions) the hydraulic aperture was compared to the mean separation of the surfaces. At large separations the surface topography has little effect. At small separations the flow is tortuous, tending to be channeled through high-aperture regions. The parameter most affecting fluid flow through rough joints is the ratio of the mean separation between the surfaces to the root-mean-square surface height. This parameter describes the distance the surface asperities protrude into the fluid and accounts for most of the disagreement with the parallel plate model. Variations in the fractal dimension produce only a second-order effect on the fluid flow. For the range of joint closures expected during elastic deformation these results show that the actual flow rate between rough surfaces is about 70–90% of that predicted by the parallel plate model.

826 citations

••

TL;DR: In this paper, the authors measured the thickness as a function of time of liquid films as they are squeezed between molecularly smooth mica surfaces and determined the film thickness with an accuracy of 0.2 nm as they drain from ∼1 μm to a few molecular layers.

Abstract: We present measurements of the thickness as a function of time of liquid films as they are squeezed between molecularly smooth mica surfaces. Three Newtonian, nonpolar liquids have been studied: octamethylcyclotetrasiloxane, n‐tetradecane, and n‐hexadecane. The film thicknesses are determined with an accuracy of 0.2 nm as they drain from ∼1 μm to a few molecular layers. Results are in excellent agreement with the Reynolds theory of lubrication for film thicknesses above 50 nm. For thinner films the drainage is slower than the theoretical prediction, which can be accounted for by assuming that the liquid within about two molecular layers of each solid surface does not undergo shear. In very thin films the continuum Reynolds theory breaks down, as drainage occurs in a series of abrupt steps whose size matches the thickness of molecular layers in the liquid. The presence of trace amounts of water has a dramatic effect on the drainage of a nonpolar liquid between hydrophilic surfaces, causing film rupture whi...

670 citations

••

TL;DR: In this article, the potential use of a new technology of laser surface texturing (LST) in parallel thrust bearings is theoretically investigated, where the surface texture has the form of micro-dimples with pre-selected diameter, depth, and area density.

Abstract: The potential use of a new technology of laser surface texturing (LST) in parallel thrust bearings is theoretically investigated. The surface texture has the form of micro-dimples with pre-selected diameter, depth, and area density. It can be applied to only a portion of the bearing area (partial LST) or the full bearing area (full LST). Optimum parameters of the dimples, and best LST mode, are found in order to obtain maximum load carrying capacity for a thrust bearing having parallel mating surfaces. A comparison is made with optimum linear and stepped sliders showing that parallel LST sliders can provide similar load carrying capacity. Scheduled for Presentation at the 58th Annual Meeting in New York City April 28–May 1, 2003

475 citations

••

TL;DR: The most common idealization of a viscoplastic fluid is the Bingham model, which has been widely used to rationalize experimental data, even though it is a crude oversimplification of true rheological behavior.

Abstract: The archetypal feature of a viscoplastic fluid is its yield stress: If the material is not sufficiently stressed, it behaves like a solid, but once the yield stress is exceeded, the material flows like a fluid. Such behavior characterizes materials common in industries such as petroleum and chemical processing, cosmetics, and food processing and in geophysical fluid dynamics. The most common idealization of a viscoplastic fluid is the Bingham model, which has been widely used to rationalize experimental data, even though it is a crude oversimplification of true rheological behavior. The popularity of the model is in its apparent simplicity. Despite this, the sudden transition between solid-like behavior and flow introduces significant complications into the dynamics, which, as a result, has resisted much analysis. Over recent decades, theoretical developments, both analytical and computational, have provided a better understanding of the effect of the yield stress. Simultaneously, greater insight into the material behavior of real fluids has been afforded by advances in rheometry. These developments have primed us for a better understanding of the various applications in the natural and engineering sciences.

474 citations

••

TL;DR: In this article, the authors present a review of the mechanical properties of wet granular media, with particular emphasis on the effect of cohesion and open problems that might motivate future studies in this exciting but mostly unexplored field.

Abstract: Most studies on granular physics have focused on dry granular media, with no liquids between the grains. However, in geology and many real world applications (e.g. food processing, pharmaceuticals, ceramics, civil engineering, construction, and many industrial applications), liquid is present between the grains. This produces inter-grain cohesion and drastically modifies the mechanical properties of the granular media (e.g. the surface angle can be larger than 90 degrees). Here we present a review of the mechanical properties of wet granular media, with particular emphasis on the effect of cohesion. We also list several open problems that might motivate future studies in this exciting but mostly unexplored field.

439 citations