Bertrand Raison

Bio: Bertrand Raison is an academic researcher from University of Grenoble. The author has contributed to research in topics: Fault (power engineering) & Grid. The author has an hindex of 23, co-authored 135 publications receiving 2841 citations. Previous affiliations of Bertrand Raison include Grenoble Institute of Technology & Joseph Fourier University.

Models for Bearing Damage Detection in Induction Motors Using Stator Current Monitoring

Abstract: This paper describes a new analytical model for the influence of rolling-element bearing faults on induction motor stator current. Bearing problems are one major cause for drive failures. Their detection is possible by vibration monitoring of characteristic bearing frequencies. As it is possible to detect other machine faults by monitoring the stator current, a great interest exists in applying the same method for bearing fault detection. After a presentation of the existing fault model, a new detailed approach is proposed. It is based on the following two effects of a bearing fault: 1. the introduction of a particular radial rotor movement and 2. load torque variations caused by the bearing fault. The theoretical study results in new expressions for the stator current frequency content. Experimental tests with artificial and realistic bearing damage were conducted by measuring vibration, torque, and stator current. The obtained results by spectral analysis of the measured quantities validate the proposed theoretical approach.

Cascaded DC–DC Converter Photovoltaic Systems: Power Optimization Issues

Abstract: This paper investigates the issues of ensuring global power optimization for cascaded dc-dc converter architectures of photovoltaic (PV) generators irrespective of the irradiance conditions. The global optimum of such connections of PV modules is generally equivalent with performing the maximum power point tracking (MPPT) on all the modules. The most important disturbance occurs when the irradiance levels of modules happen to be sensibly different from a module to another - in this case, voltage-limitation requirements may be broken. The proposed supervisory algorithm then attempts to establish the best suboptimal power regime. Validation has been achieved by MATLAB/Simulink numerical simulation in the case of a single-phase grid-connected PV system, where individual MPPTs have been implemented by an extremum-seeking control, a robust and less-knowledge-demanding perturb-and-observe method.

Radial Network Reconfiguration Using Genetic Algorithm Based on the Matroid Theory

Abstract: This paper deals with distribution network (DN) reconfiguration for loss minimization. To solve this combinatorial problem, a genetic algorithm (GA) is considered. In order to enhance its ability to explore the solution space, efficient genetic operators are developed. After a survey of the existing DN topology description methods, a theoretical approach based on the graph and matroid theories (graphic matroid in particular) is considered. These concepts are used in order to propose new intelligent and effective GA operators for efficient mutation and crossover well dedicated to the DN reconfiguration problem. All resulting individuals after GA operators are claimed to be feasible (radial) configurations. Moreover, the presented approach is valid for planar or nonplanar DN graph topologies and avoids tedious mesh checks for the topology constraint validation. The proposed method is finally compared to some previous topology coding techniques used by other authors. The results show smaller or at least equal power losses with considerably less computation effort.

Maximizing the Power Output of Partially Shaded Photovoltaic Plants Through Optimization of the Interconnections Among Its Modules

Abstract: Photovoltaic applications worldwide have reported problems with shading. Passing clouds, the moving shade of a neighbor's chimney or a nearby tree, can completely compromise the power production of such plants despite their size or sophistication. In order to address this issue, this paper makes an exhaustive study of the available interconnections among the modules of a shaded photovoltaic field and how they impact power production. As a result, a clear relationship between the interconnections of the PV modules and their power output is proposed through empirical connection laws.

Overview of Control and Grid Synchronization for Distributed Power Generation Systems

Abstract: Renewable energy sources like wind, sun, and hydro are seen as a reliable alternative to the traditional energy sources such as oil, natural gas, or coal. Distributed power generation systems (DPGSs) based on renewable energy sources experience a large development worldwide, with Germany, Denmark, Japan, and USA as leaders in the development in this field. Due to the increasing number of DPGSs connected to the utility network, new and stricter standards in respect to power quality, safe running, and islanding protection are issued. As a consequence, the control of distributed generation systems should be improved to meet the requirements for grid interconnection. This paper gives an overview of the structures for the DPGS based on fuel cell, photovoltaic, and wind turbines. In addition, control structures of the grid-side converter are presented, and the possibility of compensation for low-order harmonics is also discussed. Moreover, control strategies when running on grid faults are treated. This paper ends up with an overview of synchronization methods and a discussion about their importance in the control

Step-Up DC–DC Converters: A Comprehensive Review of Voltage-Boosting Techniques, Topologies, and Applications

Abstract: DC–DC converters with voltage boost capability are widely used in a large number of power conversion applications, from fraction-of-volt to tens of thousands of volts at power levels from milliwatts to megawatts. The literature has reported on various voltage-boosting techniques, in which fundamental energy storing elements (inductors and capacitors) and/or transformers in conjunction with switch(es) and diode(s) are utilized in the circuit. These techniques include switched capacitor (charge pump), voltage multiplier, switched inductor/voltage lift, magnetic coupling, and multistage/-level, and each has its own merits and demerits depending on application, in terms of cost, complexity, power density, reliability, and efficiency. To meet the growing demand for such applications, new power converter topologies that use the above voltage-boosting techniques, as well as some active and passive components, are continuously being proposed. The permutations and combinations of the various voltage-boosting techniques with additional components in a circuit allow for numerous new topologies and configurations, which are often confusing and difficult to follow. Therefore, to present a clear picture on the general law and framework of the development of next-generation step-up dc–dc converters, this paper aims to comprehensively review and classify various step-up dc–dc converters based on their characteristics and voltage-boosting techniques. In addition, the advantages and disadvantages of these voltage-boosting techniques and associated converters are discussed in detail. Finally, broad applications of dc–dc converters are presented and summarized with comparative study of different voltage-boosting techniques.

Multi-level conversion : high voltage choppers and voltage-source inverters

Abstract: The authors discuss high-voltage power conversion. Conventional series connection and three-level voltage source inverter techniques are reviewed and compared. A novel versatile multilevel commutation cell is introduced: it is shown that this topology is safer and more simple to control, and delivers purer output waveforms. The authors show how this technique can be applied to either choppers or voltage-source inverters and generalized to any number of switches.<>

Advances in Diagnostic Techniques for Induction Machines

Abstract: This paper investigates diagnostic techniques for electrical machines with special reference to induction machines and to papers published in the last ten years. A comprehensive list of references is reported and examined, and research activities classified into four main topics: 1) electrical faults; 2) mechanical faults; 3) signal processing for analysis and monitoring; and 4) artificial intelligence and decision-making techniques.

Power Management of a Stand-Alone Wind/Photovoltaic/Fuel Cell Energy System

Abstract: This paper proposes an AC-linked hybrid wind/photovoltaic (PV)/fuel cell (FC) alternative energy system for stand-alone applications. Wind and PV are the primary power sources of the system, and an FC-electrolyzer combination is used as a backup and a long-term storage system. An overall power management strategy is designed for the proposed system to manage power flows among the different energy sources and the storage unit in the system. A simulation model for the hybrid energy system has been developed using MATLAB/Simulink. The system performance under different scenarios has been verified by carrying out simulation studies using a practical load demand profile and real weather data.