Bhagwati Prasad Kashyap

Bio: Bhagwati Prasad Kashyap is an academic researcher from Indian Institute of Technology Bombay. The author has contributed to research in topics: Strain rate & Superplasticity. The author has an hindex of 31, co-authored 148 publications receiving 2796 citations. Previous affiliations of Bhagwati Prasad Kashyap include University of Manitoba & University of California, Davis.

High-Temperature Tensile Flow Behavior of Caliber-Rolled Mg-3Al-1Zn Alloy

Abstract: Mg-3Al-1Zn (AZ31) alloy was caliber rolled isothermally in the temperature range of 523 K to 723 K (250 °C to 450 °C) to develop fine grains of 3 to 13 µm. Tensile tests by constant initial strain rate as well as differential strain rate test techniques were conducted over the temperature range of 493 K to 723 K (220 °C to 450 °C) and strain rate range of 10−5 to 10−1 s−1. Maximum tensile elongation of 182 pct was obtained at test temperature of 723 K (450 °C) and strain rate of 10−3 s−1 in the sample obtained from caliber rolling at 723 K (450 °C), in spite of its large grain size of 13 µm. The strain rate sensitivity index ‘m’ was found to vary from 0.08 to 0.33 and activation energy for deformation ‘Q’ varied from 30 to 185 kJ mol−1 depending on test condition and caliber-rolling condition. These variations in m and Q values are explained by the difference in prior grain size, texture, and twins developed as a function of caliber-rolling temperature, and further by the concomitant microstructural change occurring during tensile test itself. The presence of twins and orientation of grains influences the parameters of the constitutive relation to varying extent.

Modeling the High Temperature Deformation Behaviour of a near Alpha Titanium Alloy with Bi-Modal Microstructure

Abstract: The high temperature deformation behaviour of near alpha titanium alloy IMI834 with a bimodal microstructure has been evaluated by carrying out isothermal compression tests over a range of temperature and strain rate The optimum thermomechanical processing (TMP) parameters ie, temperature, strain rate that can be used to produce various aeroengine components were identified using dynamic materials modeling (DMM) Using kinetic analysis, a unified constitutive equation that describes the deformation behavior of the material in the selected temperature - strain rate regime has been established and the deformation mechanisms operating in the material were identified

Effect of Rolling on Microstructure and Room Temperature Tensile Properties of Newly Developed Mg-4Li-1Ca Alloy

Abstract: Mg-30Ca and Mg-14Li (wt %) master alloys were melted successively in the induction furnace to obtain a Mg-Li-Ca ternary alloy containing 3.99 % Li and 1 % Ca. The as-cast material of thickness 4 mm was homogenised at 350° C for 120 mins and subsequently rolled to 62.5 % reduction in thickness at 300 °C to get 1.5 mm thick sheet. The microstructures of hot rolled samples were examined in as-rolled condition as well as after annealing at 350° C for various lengths of time. The presence of deformation twins was clearly seen in the as-rolled structure, whereas equiaxed twin-free grains were observed in the annealed condition. The average grain size was found to increase from 10 μm to 18 μm by annealing, according to the kinetics that follows a parabolic law. Tensile samples taken from rolled plate were deformed to failure at room temperature and a strain rate of 10-4 s-1. Ultimate tensile strength of as-rolled material increased to 213 MPa, while tensile elongation dropped to 6.5 % from the initial values of 134 MPa and 8.5 %, respectively. Annealing after rolling offered a good compromise between the enhanced tensile strength (160 MPa) and tensile ductility (9 %) suggesting viability of the proposed thermomechanical treatment as a means for enhancing both strength and ductility of Mg-4Li-1Ca alloy.

Phd by thesis

Abstract: Deposits of clastic carbonate-dominated (calciclastic) sedimentary slope systems in the rock record have been identified mostly as linearly-consistent carbonate apron deposits, even though most ancient clastic carbonate slope deposits fit the submarine fan systems better. Calciclastic submarine fans are consequently rarely described and are poorly understood. Subsequently, very little is known especially in mud-dominated calciclastic submarine fan systems. Presented in this study are a sedimentological core and petrographic characterisation of samples from eleven boreholes from the Lower Carboniferous of Bowland Basin (Northwest England) that reveals a >250 m thick calciturbidite complex deposited in a calciclastic submarine fan setting. Seven facies are recognised from core and thin section characterisation and are grouped into three carbonate turbidite sequences. They include: 1) Calciturbidites, comprising mostly of highto low-density, wavy-laminated bioclast-rich facies; 2) low-density densite mudstones which are characterised by planar laminated and unlaminated muddominated facies; and 3) Calcidebrites which are muddy or hyper-concentrated debrisflow deposits occurring as poorly-sorted, chaotic, mud-supported floatstones. These

Mechanical Behavior of Materials

Abstract: A balanced mechanics-materials approach and coverage of the latest developments in biomaterials and electronic materials, the new edition of this popular text is the most thorough and modern book available for upper-level undergraduate courses on the mechanical behavior of materials To ensure that the student gains a thorough understanding the authors present the fundamental mechanisms that operate at micro- and nano-meter level across a wide-range of materials, in a way that is mathematically simple and requires no extensive knowledge of materials This integrated approach provides a conceptual presentation that shows how the microstructure of a material controls its mechanical behavior, and this is reinforced through extensive use of micrographs and illustrations New worked examples and exercises help the student test their understanding Further resources for this title, including lecture slides of select illustrations and solutions for exercises, are available online at wwwcambridgeorg/97800521866758

Recent developments in stainless steels

Abstract: This article presents an overview of the developments in stainless steels made since the 1990s. Some of the new applications that involve the use of stainless steel are also introduced. A brief introduction to the various classes of stainless steels, their precipitate phases and the status quo of their production around the globe is given first. The advances in a variety of subject areas that have been made recently will then be presented. These recent advances include (1) new findings on the various precipitate phases (the new J phase, new orientation relationships, new phase diagram for the Fe–Cr system, etc.); (2) new suggestions for the prevention/mitigation of the different problems and new methods for their detection/measurement and (3) new techniques for surface/bulk property enhancement (such as laser shot peening, grain boundary engineering and grain refinement). Recent developments in topics like phase prediction, stacking fault energy, superplasticity, metadynamic recrystallisation and the calculation of mechanical properties are introduced, too. In the end of this article, several new applications that involve the use of stainless steels are presented. Some of these are the use of austenitic stainless steels for signature authentication (magnetic recording), the utilisation of the cryogenic magnetic transition of the sigma phase for hot spot detection (the Sigmaplugs), the new Pt-enhanced radiopaque stainless steel (PERSS) coronary stents and stainless steel stents that may be used for magnetic drug targeting. Besides recent developments in conventional stainless steels, those in the high-nitrogen, low-Ni (or Ni-free) varieties are also introduced. These recent developments include new methods for attaining very high nitrogen contents, new guidelines for alloy design, the merits/demerits associated with high nitrogen contents, etc.

Additively manufactured hierarchical stainless steels with high strength and ductility

Abstract: Many traditional approaches for strengthening steels typically come at the expense of useful ductility, a dilemma known as strength-ductility trade-off. New metallurgical processing might offer the possibility of overcoming this. Here we report that austenitic 316L stainless steels additively manufactured via a laser powder-bed-fusion technique exhibit a combination of yield strength and tensile ductility that surpasses that of conventional 316L steels. High strength is attributed to solidification-enabled cellular structures, low-angle grain boundaries, and dislocations formed during manufacturing, while high uniform elongation correlates to a steady and progressive work-hardening mechanism regulated by a hierarchically heterogeneous microstructure, with length scales spanning nearly six orders of magnitude. In addition, solute segregation along cellular walls and low-angle grain boundaries can enhance dislocation pinning and promote twinning. This work demonstrates the potential of additive manufacturing to create alloys with unique microstructures and high performance for structural applications.