Bhagwati Prasad Kashyap

Bio: Bhagwati Prasad Kashyap is an academic researcher from Indian Institute of Technology Bombay. The author has contributed to research in topics: Strain rate & Superplasticity. The author has an hindex of 31, co-authored 148 publications receiving 2796 citations. Previous affiliations of Bhagwati Prasad Kashyap include University of Manitoba & University of California, Davis.

Microstructure and properties of hot extruded Cu–1wt% Al2O3 nano-composites synthesized by various techniques

Abstract: Cu–1 wt% Al2O3 nano-composites were prepared by three different methods, namely mechanical alloying, combustion synthesis and electrical explosion of wire, in order to investigate the effect of power processing technique on microstructure and ambient properties. The powders produced by these techniques were hydrogen reduced at 500 °C and subsequently vacuum encapsulated in copper container followed by consolidation using hot extrusion at 800 °C and 600 MPa to nearly full density. As-synthesized composite powders as well as the extruded samples were characterized by scanning electron microscope, X-ray diffraction, transmission electron microscope, thermal conductivity and electrical conductivity. Microhardness and room temperature deformation behavior in compression at a strain rate of 10−4 s−1 were measured. The mechanically milled powders, upon consolidation, exhibited a finer grain size of 146 nm and a hardness of 164 HV1.0 compared to that obtained by two other techniques, which ranged between 179–390 nm and 135–156 HV1.0, respectively. The physical and mechanical properties were found to vary with grain size according to the Hall-Petch type relationship, irrespective of the processing technique employed for getting these grain sizes.

Recrystallization Phenomena During Friction Stir Processing of Hypereutectic Aluminum-Silicon Alloy

Abstract: Microstructural evolution and related dynamic recrystallization phenomena were investigated in overlapping multipass friction stir processing (FSP) of hypereutectic Al-30 pct Si alloy. FSP resulted in the elimination of porosities along with the refinement of primary silicon particles and alpha aluminum grains. These alpha aluminum grains predominantly exhibit high angle boundaries with various degrees of recovered substructure and dislocation densities. The substructure and grain formation during FSP take place primarily by annihilation and reorganization of dislocations in the grain interior and at low angle grain boundary. During multipass overlap FSP, small second phase particles were observed to form, which are accountable for pinning the grain boundaries and thus restricting their growth. During the multipass overlap FSP, the microstructure undergoes continuous dynamic recrystallization by formation of the subgrain boundary and subgrain growth to the grain structure comprising of mostly high angle grain boundaries.

Trigger Stress for Stress-Induced Martensitic Transformation during Tensile Deformation in Ti-Al-Nb Alloys: Effect of Grain Size

Abstract: The effect of β grain size on trigger stress for stress-induced martensitic transformation during tensile deformation in Ti-Al-Nb alloys was investigated. The trigger stress for stress-induced martensitic transformation (SIMT) in Ti-Al-Nb alloys exhibited a U-shaped behavior with variation in grain size. The variation of trigger stress with grain size was explained qualitatively, in terms of the contrasting change in the internal elastic energy stored in matrix due to formation of martensite (ΔEel) and the irreversible work done in overcoming the internal frictional resistance to phase boundary movement (∂Eirr) with β grain size.

Phd by thesis

Abstract: Deposits of clastic carbonate-dominated (calciclastic) sedimentary slope systems in the rock record have been identified mostly as linearly-consistent carbonate apron deposits, even though most ancient clastic carbonate slope deposits fit the submarine fan systems better. Calciclastic submarine fans are consequently rarely described and are poorly understood. Subsequently, very little is known especially in mud-dominated calciclastic submarine fan systems. Presented in this study are a sedimentological core and petrographic characterisation of samples from eleven boreholes from the Lower Carboniferous of Bowland Basin (Northwest England) that reveals a >250 m thick calciturbidite complex deposited in a calciclastic submarine fan setting. Seven facies are recognised from core and thin section characterisation and are grouped into three carbonate turbidite sequences. They include: 1) Calciturbidites, comprising mostly of highto low-density, wavy-laminated bioclast-rich facies; 2) low-density densite mudstones which are characterised by planar laminated and unlaminated muddominated facies; and 3) Calcidebrites which are muddy or hyper-concentrated debrisflow deposits occurring as poorly-sorted, chaotic, mud-supported floatstones. These

Mechanical Behavior of Materials

Abstract: A balanced mechanics-materials approach and coverage of the latest developments in biomaterials and electronic materials, the new edition of this popular text is the most thorough and modern book available for upper-level undergraduate courses on the mechanical behavior of materials To ensure that the student gains a thorough understanding the authors present the fundamental mechanisms that operate at micro- and nano-meter level across a wide-range of materials, in a way that is mathematically simple and requires no extensive knowledge of materials This integrated approach provides a conceptual presentation that shows how the microstructure of a material controls its mechanical behavior, and this is reinforced through extensive use of micrographs and illustrations New worked examples and exercises help the student test their understanding Further resources for this title, including lecture slides of select illustrations and solutions for exercises, are available online at wwwcambridgeorg/97800521866758

Recent developments in stainless steels

Abstract: This article presents an overview of the developments in stainless steels made since the 1990s. Some of the new applications that involve the use of stainless steel are also introduced. A brief introduction to the various classes of stainless steels, their precipitate phases and the status quo of their production around the globe is given first. The advances in a variety of subject areas that have been made recently will then be presented. These recent advances include (1) new findings on the various precipitate phases (the new J phase, new orientation relationships, new phase diagram for the Fe–Cr system, etc.); (2) new suggestions for the prevention/mitigation of the different problems and new methods for their detection/measurement and (3) new techniques for surface/bulk property enhancement (such as laser shot peening, grain boundary engineering and grain refinement). Recent developments in topics like phase prediction, stacking fault energy, superplasticity, metadynamic recrystallisation and the calculation of mechanical properties are introduced, too. In the end of this article, several new applications that involve the use of stainless steels are presented. Some of these are the use of austenitic stainless steels for signature authentication (magnetic recording), the utilisation of the cryogenic magnetic transition of the sigma phase for hot spot detection (the Sigmaplugs), the new Pt-enhanced radiopaque stainless steel (PERSS) coronary stents and stainless steel stents that may be used for magnetic drug targeting. Besides recent developments in conventional stainless steels, those in the high-nitrogen, low-Ni (or Ni-free) varieties are also introduced. These recent developments include new methods for attaining very high nitrogen contents, new guidelines for alloy design, the merits/demerits associated with high nitrogen contents, etc.

Additively manufactured hierarchical stainless steels with high strength and ductility

Abstract: Many traditional approaches for strengthening steels typically come at the expense of useful ductility, a dilemma known as strength-ductility trade-off. New metallurgical processing might offer the possibility of overcoming this. Here we report that austenitic 316L stainless steels additively manufactured via a laser powder-bed-fusion technique exhibit a combination of yield strength and tensile ductility that surpasses that of conventional 316L steels. High strength is attributed to solidification-enabled cellular structures, low-angle grain boundaries, and dislocations formed during manufacturing, while high uniform elongation correlates to a steady and progressive work-hardening mechanism regulated by a hierarchically heterogeneous microstructure, with length scales spanning nearly six orders of magnitude. In addition, solute segregation along cellular walls and low-angle grain boundaries can enhance dislocation pinning and promote twinning. This work demonstrates the potential of additive manufacturing to create alloys with unique microstructures and high performance for structural applications.