Brian A. Fleck

Bio: Brian A. Fleck is an academic researcher from University of Alberta. The author has contributed to research in topics: Jet (fluid) & Reynolds number. The author has an hindex of 17, co-authored 75 publications receiving 1466 citations.

A Novel Approach Toward Fabrication of High Performance Thin Film Composite Polyamide Membranes.

Abstract: A practical method is reported to enhance water permeability of thin film composite (TFC) polyamide (PA) membranes by decreasing the thickness of the selective PA layer. The composite membranes were prepared by interfacial polymerization (IP) reaction between meta-phenylene diamine (MPD)-aqueous and trimesoyl chloride (TMC)-organic solvents at the surface of polyethersulfone (PES) microporous support. Several PA TFC membranes were prepared at different temperatures of the organic solution ranging from −20 °C to 50 °C. The physico-chemical and morphological properties of the synthesized membranes were carefully characterized using serval analytical techniques. The results confirmed that the TFC membranes, synthesized at sub-zero temperatures of organic solution, had thinner and smoother PA layer with a greater degree of cross-linking and wettability compared to the PA films prepared at 50 °C. We demonstrated that reducing the temperature of organic solution effectively decreased the thickness of the PA active layer and thus enhanced water permeation through the membranes. The most water permeable membrane was prepared at −20 °C and exhibited nine times higher water flux compared to the membrane synthesized at room temperature. The method proposed in this report can be effectively applied for energy- and cost-efficient development of high performance nanofiltration and reverse osmosis membranes.

Thin film composite polyamide membranes: parametric study on the influence of synthesis conditions

Abstract: Preparation of thin film composite (TFC) polyamide (PA) membranes by interfacial polymerization (IP) reaction is remarkably sensitive to the interactions between synthesis parameters. Here we report the effect of the simultaneous change in four synthesis parameters, namely monomers concentrations (m-phenylenediamine, MPD, and trimesoyl chloride, TMC), reaction time and curing temperature, on the surface morphology and on the permeation properties of TFC membranes. By varying several synthesis parameters at the same time using a Taguchi robust design (L9 orthogonal arrays), it was found that monomers concentration and curing temperature significantly affected water permeation by creating a substantial change in morphology of the PA films. More importantly, a strong interaction between monomers concentration was observed, which demonstrates the importance of smart adjustment of these parameters in the preparation process. Permeation properties were justified by thickness and by the cross-link density of the synthesized films; the latter was found to be more influential. Based on analysis of variance (ANOVA), the contribution of the synthesis parameters towards change in water permeation was determined as: curing temperature (40.7%) > MPD concentration (28%) ∼ TMC concentration (27.8%) > reaction time (1.9%). The findings will provide valuable guidelines to develop practical low cost, robust and high performance membranes by changing the curing temperature and the monomer concentrations as critical parameters.

Review of biodiesel composition, properties, and specifications

Abstract: Biodiesel is a renewable transportation fuel consisting of fatty acid methyl esters (FAME), generally produced by transesterification of vegetable oils and animal fats. In this review, the fatty acid (FA) profiles of 12 common biodiesel feedstocks were summarized. Considerable compositional variability exists across the range of feedstocks. For example, coconut, palm and tallow contain high amounts of saturated FA; while corn, rapeseed, safflower, soy, and sunflower are dominated by unsaturated FA. Much less information is available regarding the FA profiles of algal lipids that could serve as biodiesel feedstocks. However, some algal species contain considerably higher levels of poly-unsaturated FA than is typically found in vegetable oils. Differences in chemical and physical properties among biodiesel fuels can be explained largely by the fuels’ FA profiles. Two features that are especially influential are the size distribution and the degree of unsaturation within the FA structures. For the 12 biodiesel types reviewed here, it was shown that several fuel properties – including viscosity, specific gravity, cetane number, iodine value, and low temperature performance metrics – are highly correlated with the average unsaturation of the FAME profiles. Due to opposing effects of certain FAME structural features, it is not possible to define a single composition that is optimum with respect to all important fuel properties. However, to ensure satisfactory in-use performance with respect to low temperature operability and oxidative stability, biodiesel should contain relatively low concentrations of both long-chain saturated FAME and poly-unsaturated FAME.

Wind turbine design with emphasis on Darrieus concept Ion Paraschivoiu

Abstract: Wind energy is the fastest growing alternate source of energy in the world since its purely economic potential is complemented by its great positive environmental impact. The wind turbine, whether it may be a Horizontal-Axis Wind Turbine (HAWT) or a Vertical-Axis Wind Turbine (VAWT), offers a practical way to convert the wind energy into electrical or mechanical energy. Although this book focuses on the aerodynamic design and performance of VAWTs based on the Darrieus concept, it also discusses the comparison between HAWTs and VAWTs, future trends in design and the inherent socio-economic and environmental friendly aspects of wind energy as an alternate source of energy.