Chen Cheng

Bio: Chen Cheng is an academic researcher from Soochow University (Suzhou). The author has contributed to research in topics: Porous medium & Wetting. The author has co-authored 1 publications.

Emulsion-templated porous polymers: drying condition-dependent properties.

Abstract: Macroporous materials templated using high internal phase emulsions (HIPEs) are promising for various applications. To date, new strategies to create emulsion-templated porous materials and to tune their properties (especially wetting properties) are still highly required. Here, we report the fabrication of macroporous polymers from oil-in-water HIPEs, bereft of conventional monomers and crosslinking monomers, by simultaneous ring-opening polymerization and interface-catalyzed condensation, without heating or removal of oxygen. The resulting macroporous polymers showed drying condition-dependent wetting properties (e.g., hydrophilicity–oleophilicity from freezing drying, hydrophilicity–oleophobicity from vacuum drying, and amphiphobicity from heat drying), densities (from 0.019 to 0.350 g cc−1), and compressive properties. Hydrophilic–oleophilic and amphiphobic porous polymers turned hydrophilic–oleophobic simply by heating and protonation, respectively. The hydrophilic–oleophobic porous polymers could remove a small amount of water from oil–water mixtures (including surfactant-stabilized water-in-oil emulsions) by selective absorption and could remove water-soluble dyes from oil–water mixtures. Moreover, the transition in wetting properties enabled the removal of water and dyes in a controlled manner. The feature that combines simply preparation, tunable wetting properties and densities, robust compression, high absorption capacity (rate) and controllable absorption makes the porous polymers to be excellent candidates for the removal of water and water-soluble dyes from oil–water mixtures.

Preparation of polymer-based foam for efficient oil-water separation based on surface engineering.

Abstract: The leakages of a large number of organic solvents and oil spills not only cause extensive economic losses, but also destroy the ecological environment. However, there were few studies on the surface engineering of adsorption materials for efficient oil-water separation in complex environments. In this research, through surface engineering, the polymer-based foam exhibited high efficiency oil-water separation performance in different pH environments. Hydrophobic groups were introduced onto the surface of nano-sized SiO2 particles via hydrolysis and polycondensation reactions, and then the modified SiO2 was loaded on the foam. After modification, the water contact angle of the modified foam increased from 116.4° to 152.5°, and the oil-water separation performance was obviously enhanced. The oil removal rate of the modified foam remained above 96%. The highest capacity of petroleum diesel was 33.4 g-1, which was much higher than other similar adsorption materials. In addition, the modified foam maintained good hydrophobicity and oil removal rate in a wide pH range. The efficient oleophilic and hydrophobic foam prepared by combining green physical foaming with surface engineering was expected to be widely used in large-scale organic solvent recovery and oil leakage emergency treatment.

Emulsion-Templated, Magnetic, Hydrophilic–Oleophobic Composites for Controlled Water Removal

Abstract: Emulsion-templated, hydrophilic-oleophobic porous materials are promising for the removal of a small amount of water from oil-water mixtures, but the maneuver and complete collection of these porous materials are challenging. Herein, we report the fabrication of magnetic, hydrophilic-oleophobic polyHIPE composites from reactive Fe3O4 nanoparticle-stabilized high internal phase emulsions through simultaneous bulk polymerization of water-soluble monomers and interface-catalyzed polycondensation of 1H,1H,2H,2H-perfluorooctyltriethoxysilane. The resulting composites were hydrophilic-oleophobic, with water droplets rapidly absorbed (within 20 s), and exhibited designable magnetic responsiveness. The hydrophilicity-oleophobicity enabled water to be removed through selective absorption from oil-water mixtures (including surfactant-stabilized water-in-oil emulsions), with a high separation rate over 99%. The magnetic-responsiveness enabled both the dry and the swollen composites to be maneuvered in a remote and contactless manner and to be fully collected. Therefore, the magnetic, hydrophilic-oleophobic polyHIPE composites are excellent candidates for the removal of water from water-oil mixtures with complete collection.