Dezhi Wang

Bio: Dezhi Wang is an academic researcher from Texas Center for Superconductivity. The author has contributed to research in topics: Thermoelectric effect & Thermoelectric materials. The author has an hindex of 37, co-authored 73 publications receiving 18881 citations. Previous affiliations of Dezhi Wang include University of Houston & Massachusetts Institute of Technology.

High-Thermoelectric Performance of Nanostructured Bismuth Antimony Telluride Bulk Alloys

Abstract: The dimensionless thermoelectric figure of merit (ZT) in bismuth antimony telluride (BiSbTe) bulk alloys has remained around 1 for more than 50 years. We show that a peak ZT of 1.4 at 100°C can be achieved in a p-type nanocrystalline BiSbTe bulk alloy. These nanocrystalline bulk materials were made by hot pressing nanopowders that were ball-milled from crystalline ingots under inert conditions. Electrical transport measurements, coupled with microstructure studies and modeling, show that the ZT improvement is the result of low thermal conductivity caused by the increased phonon scattering by grain boundaries and defects. More importantly, ZT is about 1.2 at room temperature and 0.8 at 250°C, which makes these materials useful for cooling and power generation. Cooling devices that use these materials have produced high-temperature differences of 86°, 106°, and 119°C with hot-side temperatures set at 50°, 100°, and 150°C, respectively. This discovery sets the stage for use of a new nanocomposite approach in developing high-performance low-cost bulk thermoelectric materials.

New Directions for Low-Dimensional Thermoelectric Materials**

Abstract: Many of the recent advances in enhancing the thermoelectric figure of merit are linked to nanoscale phenomena found both in bulk samples containing nanoscale constituents and in nanoscale samples themselves. Prior theoretical and experimental proof-of-principle studies on quantum-well superlattice and quantum-wire samples have now evolved into studies on bulk samples containing nanostructured constituents prepared by chemical or physical approaches. In this Review, nanostructural composites are shown to exhibit nanostructures and properties that show promise for thermoelectric applications, thus bringing together low-dimensional and bulk materials for thermoelectric applications. Particular emphasis is given in this Review to the ability to achieve 1) a simultaneous increase in the power factor and a decrease in the thermal conductivity in the same nanocomposite sample and for transport in the same direction and 2) lower values of the thermal conductivity in these nanocomposites as compared to alloy samples of the same chemical composition. The outlook for future research directions for nanocomposite thermoelectric materials is also discussed.

High-performance flat-panel solar thermoelectric generators with high thermal concentration

Abstract: The conversion of sunlight into electricity has been dominated by photovoltaic and solar thermal power generation. A highly efficient solar to electric energy conversion device based on nanostructured thermoelectric materials and high solar concentration is now demonstrated. The results show potential for cost effective solar thermoelectric generation.

Enhanced thermoelectric figure-of-merit in nanostructured p-type silicon germanium bulk alloys.

Abstract: A dimensionless thermoelectric figure-of-merit (ZT) of 0.95 in p-type nanostructured bulk silicon germanium (SiGe) alloys is achieved, which is about 90% higher than what is currently used in space flight missions, and 50% higher than the reported record in p-type SiGe alloys. These nanostructured bulk materials were made by using a direct current-induced hot press of mechanically alloyed nanopowders that were initially synthesized by ball milling of commercial grade Si and Ge chunks with boron powder. The enhancement of ZT is due to a large reduction of thermal conductivity caused by the increased phonon scattering at the grain boundaries of the nanostructures combined with an increased power factor at high temperatures.

Complex thermoelectric materials.

Abstract: Thermoelectric materials, which can generate electricity from waste heat or be used as solid-state Peltier coolers, could play an important role in a global sustainable energy solution. Such a development is contingent on identifying materials with higher thermoelectric efficiency than available at present, which is a challenge owing to the conflicting combination of material traits that are required. Nevertheless, because of modern synthesis and characterization techniques, particularly for nanoscale materials, a new era of complex thermoelectric materials is approaching. We review recent advances in the field, highlighting the strategies used to improve the thermopower and reduce the thermal conductivity.

Two-Dimensional Nanosheets Produced by Liquid Exfoliation of Layered Materials

Abstract: If they could be easily exfoliated, layered materials would become a diverse source of two-dimensional crystals whose properties would be useful in applications ranging from electronics to energy storage. We show that layered compounds such as MoS2, WS2, MoSe2, MoTe2, TaSe2, NbSe2, NiTe2, BN, and Bi2Te3 can be efficiently dispersed in common solvents and can be deposited as individual flakes or formed into films. Electron microscopy strongly suggests that the material is exfoliated into individual layers. By blending this material with suspensions of other nanomaterials or polymer solutions, we can prepare hybrid dispersions or composites, which can be cast into films. We show that WS2 and MoS2 effectively reinforce polymers, whereas WS2/carbon nanotube hybrid films have high conductivity, leading to promising thermoelectric properties.

Cooling, heating, generating power, and recovering waste heat with thermoelectric systems.

Abstract: Thermoelectric materials are solid-state energy converters whose combination of thermal, electrical, and semiconducting properties allows them to be used to convert waste heat into electricity or electrical power directly into cooling and heating. These materials can be competitive with fluid-based systems, such as two-phase air-conditioning compressors or heat pumps, or used in smaller-scale applications such as in automobile seats, night-vision systems, and electrical-enclosure cooling. More widespread use of thermoelectrics requires not only improving the intrinsic energy-conversion efficiency of the materials but also implementing recent advancements in system architecture. These principles are illustrated with several proven and potential applications of thermoelectrics.

High-Thermoelectric Performance of Nanostructured Bismuth Antimony Telluride Bulk Alloys

Abstract: The dimensionless thermoelectric figure of merit (ZT) in bismuth antimony telluride (BiSbTe) bulk alloys has remained around 1 for more than 50 years. We show that a peak ZT of 1.4 at 100°C can be achieved in a p-type nanocrystalline BiSbTe bulk alloy. These nanocrystalline bulk materials were made by hot pressing nanopowders that were ball-milled from crystalline ingots under inert conditions. Electrical transport measurements, coupled with microstructure studies and modeling, show that the ZT improvement is the result of low thermal conductivity caused by the increased phonon scattering by grain boundaries and defects. More importantly, ZT is about 1.2 at room temperature and 0.8 at 250°C, which makes these materials useful for cooling and power generation. Cooling devices that use these materials have produced high-temperature differences of 86°, 106°, and 119°C with hot-side temperatures set at 50°, 100°, and 150°C, respectively. This discovery sets the stage for use of a new nanocomposite approach in developing high-performance low-cost bulk thermoelectric materials.