Intersections of shear bands in metastable austenites have been shown to be effective sites for strain-induced martensitic nucleation. The shear bands may be in the form of e’ (hcp) martensite, mechanical twins, or dense bundles of stacking faults. Assuming that shear-band intersection is the dominant mechanism of strain-induced nucleation, an expression for the volume fraction of martensite vs plastic strain is derived by considering the course of shear-band formation, the probability of shear-band intersections, and the probability of an intersection generating a martensitic embryo. The resulting transformation curve has a sigmoidal shape and, in general, approaches saturation below 100 pct. The saturation value and rate of approach to saturation are determined by two temperature-dependent parameters related to the fee-bee chemical driving force and austenite stacking-fault energy. Fitting the expression to available data on 304 stainless steels gives good agreement for the shape of individual transformation curves as well as the temperature dependence of the derived parameters. It is concluded that the temperature dependence of the transformation kinetics (an important problem in the development of TRIP steels) may be minimized by decreasing the fee, bec, and hep entropy differences through proper compositional control.

Kinetics of strain-induced martensitic nucleation

Formation of Shear Bands and Strain-induced Martensite During Plastic Deformation of Metastable Austenitic Stainless Steels

Consideration of the martensitic nucleation process as a sequence of steps which take the particle from maximum to minimum coherency leads to the hypothesis that the first step in martensitic nucleation is faulting on planes of closest packing. It is further postulated that the faulting displacements are derived from an existing defect, while matrix constraints cause all subsequent processes to occur in such a way as to leave the fault plane unrotated, thus accounting for the observed general orientation relations. Using basic concepts of classical nucleation theory, the stacking fault energy is shown to consist of both volume energy and surface energy contributions. When the volume energy contribution is negative, the fault energy decreases with increasing fault thickness such that the fault energy associated with the simultaneous dissociation of an appropriate group of dislocations (e.g. a finite tilt boundary segment) can be zero or negative. This condition leads to the spontaneous formation of a martensitic embryo. For the specific case of the fcc → hcp martensitic transformation in Fe-Cr-Ni alloys, the defect necessary to account for spontaneous embryo formation at the observedM
 s temperatures may consist of four or five properly spaced lattice dislocations. Such defects are considered to be consistent with the known sparseness of initial martensitic nucleation sites.

A general mechanism of martensitic nucleation: Part I. General concepts and the FCC → HCP transformation

Dependence of tensile deformation behavior of TWIP steels on stacking fault energy, temperature and strain rate

Effect of processing parameters on microstructure and tensile properties of austenitic stainless steel 304L made by directed energy deposition additive manufacturing

Martensitic transformations induced by plastic deformation are studied comparatively in various alloys of three types: Fe-30 pct Ni, Fe-20 pct Ni-7 pct Cr, and Fe-16 pet Cr-13 pct Ni, with carbon content up to 0.3 pct. For all these alloys the tensile properties vary rapidly with temperature, but there are large differences in the value of the temperature rangeM s toM d, which strongly increases with substitution of chromium for nickel or with carbon addition. Using the node method, it is found that the intrinsic stacking fault energy in the austenite drastically increases with temperature in all the chromium-bearing alloys investigated. This variation is consistent with the observed influence of temperature on the appearance of twinning or e martensite during plastic deformation. Very different α’ martensite morphologies can result from spontaneous and plastic deformation induced transformations, especially in Fe-20 pct Ni-7 pct Cr-type alloys where platelike and lath martensites are respectively observed. As in the case of e martensite, the nucleation process is analyzed as a deformation mode of the material, using a dislocation model. It is then possible to account for the morphology of plastic deformation induced α’ martensite in both Fe-20 pct Ni-7 pct Cr and Fe-16 pct Cr-13 pct Ni types alloys and for the largeM s toM d range in these alloys.

F. Lecroisey

Papers

Martensitic transformations induced by plastic deformation in the Fe-Ni-Cr-C system

Etude de la limite elastique d'un alliage durci par precipitation coherente et ordonnee