Fang Zheng Peng

Bio: Fang Zheng Peng is an academic researcher from Florida State University. The author has contributed to research in topics: Inverter & Z-source inverter. The author has an hindex of 87, co-authored 380 publications receiving 43073 citations. Previous affiliations of Fang Zheng Peng include Oak Ridge National Laboratory & Nagaoka University of Technology.

$Z$ -Source Inverter for Residential Photovoltaic Systems

Abstract: This paper proposes a Z-source inverter system for a split-phase grid-connected photovoltaic system. The operation principle, control method, and characteristics of the system are presented. A comparison between the new and traditional system configurations is performed. Simulation and experimental results are also shown to verify the proposed circuit and analysis

Harmonic and reactive power compensation based on the generalized instantaneous reactive power theory for three-phase four-wire systems

Abstract: This paper presents harmonic and reactive power compensation based on a generalized theory of instantaneous reactive power for three-phase power systems. This new theory gives a generalized definition of instantaneous reactive power, which is valid for sinusoidal or nonsinusoidal and balanced or unbalanced three-phase power systems with or without zero-sequence currents and/or voltages. The properties and physical meanings of the newly defined instantaneous reactive power are discussed in detail. A harmonic and reactive power compensator based on the new theory for a three-phase harmonic-distorted power system with zero-sequence components in the load current and/or source voltage is then used as an example to show harmonic and reactive power measurement and compensation using the new theory. Simulation and experimental results are presented.

Multilevel converters for large electric drives

Abstract: Traditional two-level high-frequency pulse width modulation (PWM) inverters for motor drives have several problems associated with their high frequency switching which produces common-mode voltage and high voltage change (dV/dt) rates to the motor windings. Multilevel inverters solve these problems because their devices can switch at a much lower frequency. Two different multilevel topologies are identified for use as a power converter for electric drives: a cascade inverter with separate DC sources; and a back-to-back diode clamped converter. The cascade inverter is a natural fit for large automotive all-electric drives because of the high VA ratings possible and because it uses several levels of DC voltage sources which would be available from batteries or fuel cells. The back-to-back diode clamped converter is ideal where a source of AC voltage is available such as a hybrid electric vehicle. Simulation and experimental results show the superiority of these two power converters over PWM-based drives.

Trans-Z-Source Inverters

Abstract: This paper extends the impedance-source (Z-source) inverters concept to the transformer-based Z-source (trans-Z-source) inverters. The original Z-source inverter (ZSI) employs an impedance network of two inductors and two capacitors connected in a special arrangement to interface the dc source and the inverter bridge. It has buck and boost function that cannot be achieved by traditional voltage-source inverters and current-source inverters. In the proposed four trans-Z-source inverters, all the impedance networks consist of a transformer and one capacitor. While maintaining the main features of the previously presented Z-source network, the new networks exhibit some unique advantages, such as the increased voltage gain and reduced voltage stress in the voltage-fed trans-ZSIs and the expanded motoring operation range in the current-fed trans-ZSIs, when the turns ratio of the transformer windings is over 1. Simulation and experimental results of the voltage-fed and the current-fed trans-ZSIs are provided to verify the analysis.

A DC-DC multilevel boost converter

Abstract: A DC-DC converter topology is proposed. The DC-DC multilevel boost converter (MBC) is a pulse-width modulation (PWM)-based DC-DC converter, which combines the boost converter and the switched capacitor function to provide different output voltages and a self-balanced voltage using only one driven switch, one inductor, 2 N -1 diodes and 2 N -1 capacitors for an Nx MBC. It is proposed to be used as DC link in applications where several controlled voltage levels are required with self-balancing and unidirectional current flow, such as photovoltaic (PV) or fuel cell generation systems with multilevel inverters; each device blocks only one voltage level, achieving high-voltage converters with low-voltage devices. The major advantages of this topology are: a continuous input current, a large conversion ratio without extreme duty cycle and without transformer, which allow high switching frequency. It can be built in a modular way and more levels can be added without modifying the main circuit. The proposed converter is simulated and prototyped; experimental results prove the proposition's principle.

Multilevel inverters: a survey of topologies, controls, and applications

Abstract: Multilevel inverter technology has emerged recently as a very important alternative in the area of high-power medium-voltage energy control. This paper presents the most important topologies like diode-clamped inverter (neutral-point clamped), capacitor-clamped (flying capacitor), and cascaded multicell with separate DC sources. Emerging topologies like asymmetric hybrid cells and soft-switched multilevel inverters are also discussed. This paper also presents the most relevant control and modulation methods developed for this family of converters: multilevel sinusoidal pulsewidth modulation, multilevel selective harmonic elimination, and space-vector modulation. Special attention is dedicated to the latest and more relevant applications of these converters such as laminators, conveyor belts, and unified power-flow controllers. The need of an active front end at the input side for those inverters supplying regenerative loads is also discussed, and the circuit topology options are also presented. Finally, the peripherally developing areas such as high-voltage high-power devices and optical sensors and other opportunities for future development are addressed.

Power-Electronic Systems for the Grid Integration of Renewable Energy Sources: A Survey

Abstract: The use of distributed energy resources is increasingly being pursued as a supplement and an alternative to large conventional central power stations. The specification of a power-electronic interface is subject to requirements related not only to the renewable energy source itself but also to its effects on the power-system operation, especially where the intermittent energy source constitutes a significant part of the total system capacity. In this paper, new trends in power electronics for the integration of wind and photovoltaic (PV) power generators are presented. A review of the appropriate storage-system technology used for the integration of intermittent renewable energy sources is also introduced. Discussions about common and future trends in renewable energy systems based on reliability and maturity of each technology are presented

Recent Advances and Industrial Applications of Multilevel Converters

Abstract: Multilevel converters have been under research and development for more than three decades and have found successful industrial application. However, this is still a technology under development, and many new contributions and new commercial topologies have been reported in the last few years. The aim of this paper is to group and review these recent contributions, in order to establish the current state of the art and trends of the technology, to provide readers with a comprehensive and insightful review of where multilevel converter technology stands and is heading. This paper first presents a brief overview of well-established multilevel converters strongly oriented to their current state in industrial applications to then center the discussion on the new converters that have made their way into the industry. In addition, new promising topologies are discussed. Recent advances made in modulation and control of multilevel converters are also addressed. A great part of this paper is devoted to show nontraditional applications powered by multilevel converters and how multilevel converters are becoming an enabling technology in many industrial sectors. Finally, some future trends and challenges in the further development of this technology are discussed to motivate future contributions that address open problems and explore new possibilities.

Multilevel converters-a new breed of power converters

Abstract: Multilevel voltage source converters are emerging as a new breed of power converter options for high-power applications. The multilevel voltage source converters typically synthesize the staircase voltage wave from several levels of DC capacitor voltages. One of the major limitations of the multilevel converters is the voltage unbalance between different levels. The techniques to balance the voltage between different levels normally involve voltage clamping or capacitor charge control. There are several ways of implementing voltage balance in multilevel converters. Without considering the traditional magnetic coupled converters, this paper presents three recently developed multilevel voltage source converters: (1) diode-clamp, (2) flying-capacitors, and (3) cascaded-inverters with separate DC sources. The operating principle, features, constraints, and potential applications of these converters are discussed.

An innovative modular multilevel converter topology suitable for a wide power range

Abstract: This paper presents a new multilevel converter topology suitable for very high voltage applications, especially network interties in power generation and transmission. The fundamental concept and the applied control scheme is introduced. Simulation results of a 36 MW-network intertie illustrate the efficient operating characteristics. A suitable structure of the converter-control is proposed.