scispace - formally typeset
Search or ask a question
Author

Franco Cacialli

Bio: Franco Cacialli is an academic researcher from London Centre for Nanotechnology. The author has contributed to research in topics: Electroluminescence & Polyfluorene. The author has an hindex of 55, co-authored 316 publications receiving 14463 citations. Previous affiliations of Franco Cacialli include University of Cambridge & University of Groningen.


Papers
More filters
Journal ArticleDOI
TL;DR: In this paper, the authors showed that the organic cation is not essential, but simply a convenience for forming lead triiodide perovskites with good photovoltaic properties.
Abstract: The vast majority of perovskite solar cell research has focused on organic–inorganic lead trihalide perovskites. Herein, we present working inorganic CsPbI3 perovskite solar cells for the first time. CsPbI3 normally resides in a yellow non-perovskite phase at room temperature, but by careful processing control and development of a low-temperature phase transition route we have stabilised the material in the black perovskite phase at room temperature. As such, we have fabricated solar cell devices in a variety of architectures, with current–voltage curve measured efficiency up to 2.9% for a planar heterojunction architecture, and stabilised power conversion efficiency of 1.7%. The well-functioning planar junction devices demonstrate long-range electron and hole transport in this material. Importantly, this work identifies that the organic cation is not essential, but simply a convenience for forming lead triiodide perovskites with good photovoltaic properties. We additionally observe significant rate-dependent current–voltage hysteresis in CsPbI3 devices, despite the absence of the organic polar molecule previously thought to be a candidate for inducing hysteresis via ferroelectric polarisation. Due to its space group, CsPbI3 cannot be a ferroelectric material, and thus we can conclude that ferroelectricity is not required to explain current–voltage hysteresis in perovskite solar cells. Our report of working inorganic perovskite solar cells paves the way for further developments likely to lead to much more thermally stable perovskite solar cells and other optoelectronic devices.

1,304 citations

Journal ArticleDOI
TL;DR: In this paper, the work function and density of states (DOS) of multiwall carbon nanotubes (MWNTs) using ultraviolet photoelectron spectroscopy (UPS) were studied.
Abstract: We have studied the work function and density of states (DOS) of multiwall carbon nanotubes (MWNTs) using ultraviolet photoelectron spectroscopy (UPS) Raw MWNTs were purified by successive sonication, centrifugation, sedimentation, and filtration processes with the aid of a nonionic surfactant The purified MWNTs showed a slightly lower work function (43 eV) than that of highly oriented pyrolytic graphite (44 eV) Effects of three different oxidative treatments, air-, oxygen plasma-, and acid-oxidation, have also been studied It was found that oxidative treatments affect the DOS of valence bands and increase the work function X-ray photoelectron spectroscopy (XPS) measurements have suggested that gas-phase treatment preferentially forms hydroxyl and carbonyl groups, while liquid-phase treatment forms carboxylic acid groups on the surface of MWNTs These surface chemical groups disrupt the π-conjugation and introduce surface dipole moments, leading to higher work functions up to 51 eV We expect the

919 citations

Journal ArticleDOI
30 Mar 2000-Nature
TL;DR: It is shown how molecular-scale engineering of these interlayers to form stepped and graded electronic profiles can lead to remarkably efficient single-layer polymer LEDs that exhibit nearly balanced injection, near-perfect recombination, and greatly reduced pre-turn-on leakage currents.
Abstract: Achieving balanced electron-hole injection and perfect recombination of the charge carriers is central to the design of efficient polymer light-emitting diodes (LEDs). A number of approaches have focused on modification of the injection contacts, for example by incorporating an additional conducting-polymer layer at the indium-tin oxide (ITO) anode. Recently, the layer-by-layer polyelectrolyte deposition route has been developed for the fabrication of ultrathin polymer layers. Using this route, we previously incorporated ultrathin (<100 A) charge-injection interfacial layers in polymer LEDs. Here we show how molecular-scale engineering of these interlayers to form stepped and graded electronic profiles can lead to remarkably efficient single-layer polymer LEDs. These devices exhibit nearly balanced injection, near-perfect recombination, and greatly reduced pre-turn-on leakage currents. A green-emitting LED comprising a poly(p-phenylene vinylene) derivative sandwiched between a calcium cathode and the modified ITO anode yields an external forward efficiency of 6.0 per cent (estimated internal efficiency, 15-20 per cent) at a luminance of 1,600 candelas per m2 at 5 V.

740 citations

Journal ArticleDOI
TL;DR: In this paper, the influence of chemical and physical treatments on the properties of indium-tin oxide (ITO) thin films were combined studies of the effect of these treatments on anodes of polymeric light-emitting diodes.
Abstract: We report combined studies of the influence of chemical and physical treatments on the properties of indium–tin oxide (ITO) thin films. The ITO films were also used as transparent anodes of polymeric light-emitting diodes (LEDs) incorporating poly(p-phenylene vinylene) (PPV) as the emitter material, with, or without, doped poly(3,4-ethylene dioxythiophene) (PEDOT) as a hole-injection/transport layer. Structures based on a soluble green derivative of PPV, poly(4,4′-diphenylene diphenylvinylene) were also tested. We studied chemical (aquaregia, degreasing, RCA protocol) and physical (oxygen and argon plasmas, Teflon, and paper rubbing) treatments and, in contrast to recently published work, we find that for Balzer Baltracon ITO, oxygen plasma and not aquaregia yields the highest efficiencies and luminances and the lowest drive voltages. For oxygen-plasma-treated anodes, the device efficiency clearly correlates with the value of the ITO surface work function, which in turn depends on the time of treatment. I...

626 citations


Cited by
More filters
Journal ArticleDOI

[...]

08 Dec 2001-BMJ
TL;DR: There is, I think, something ethereal about i —the square root of minus one, which seems an odd beast at that time—an intruder hovering on the edge of reality.
Abstract: There is, I think, something ethereal about i —the square root of minus one. I remember first hearing about it at school. It seemed an odd beast at that time—an intruder hovering on the edge of reality. Usually familiarity dulls this sense of the bizarre, but in the case of i it was the reverse: over the years the sense of its surreal nature intensified. It seemed that it was impossible to write mathematics that described the real world in …

33,785 citations

Journal ArticleDOI
TL;DR: This review gives a general introduction to the materials, production techniques, working principles, critical parameters, and stability of the organic solar cells, and discusses the alternative approaches such as polymer/polymer solar cells and organic/inorganic hybrid solar cells.
Abstract: The need to develop inexpensive renewable energy sources stimulates scientific research for efficient, low-cost photovoltaic devices.1 The organic, polymer-based photovoltaic elements have introduced at least the potential of obtaining cheap and easy methods to produce energy from light.2 The possibility of chemically manipulating the material properties of polymers (plastics) combined with a variety of easy and cheap processing techniques has made polymer-based materials present in almost every aspect of modern society.3 Organic semiconductors have several advantages: (a) lowcost synthesis, and (b) easy manufacture of thin film devices by vacuum evaporation/sublimation or solution cast or printing technologies. Furthermore, organic semiconductor thin films may show high absorption coefficients4 exceeding 105 cm-1, which makes them good chromophores for optoelectronic applications. The electronic band gap of organic semiconductors can be engineered by chemical synthesis for simple color changing of light emitting diodes (LEDs).5 Charge carrier mobilities as high as 10 cm2/V‚s6 made them competitive with amorphous silicon.7 This review is organized as follows. In the first part, we will give a general introduction to the materials, production techniques, working principles, critical parameters, and stability of the organic solar cells. In the second part, we will focus on conjugated polymer/fullerene bulk heterojunction solar cells, mainly on polyphenylenevinylene (PPV) derivatives/(1-(3-methoxycarbonyl) propyl-1-phenyl[6,6]C61) (PCBM) fullerene derivatives and poly(3-hexylthiophene) (P3HT)/PCBM systems. In the third part, we will discuss the alternative approaches such as polymer/polymer solar cells and organic/inorganic hybrid solar cells. In the fourth part, we will suggest possible routes for further improvements and finish with some conclusions. The different papers mentioned in the text have been chosen for didactical purposes and cannot reflect the chronology of the research field nor have a claim of completeness. The further interested reader is referred to the vast amount of quality papers published in this field during the past decade.

6,059 citations

Journal ArticleDOI
14 Jan 1999-Nature
TL;DR: Research in the use of organic polymers as active semiconductors in light-emitting diodes has advanced rapidly, and prototype devices now meet realistic specifications for applications.
Abstract: Research in the use of organic polymers as the active semiconductors in light-emitting diodes has advanced rapidly, and prototype devices now meet realistic specifications for applications. These achievements have provided insight into many aspects of the background science, from design and synthesis of materials, through materials fabrication issues, to the semiconductor physics of these polymers.

5,653 citations

Journal ArticleDOI
TL;DR: The restriction of intramolecular rotation is identified as a main cause for the AIE effect and a series of new fluorescent and phosphorescent AIE systems with emission colours covering the entire visible spectral region and luminescence quantum yields up to unity are developed.

3,324 citations

Journal ArticleDOI
15 Dec 2000-Science
TL;DR: It is shown that the use of substrate surface energy patterning to direct the flow of water-based conducting polymer inkjet droplets enables high-resolution definition of practical channel lengths of 5 micrometers, and high mobilities were achieved.
Abstract: Direct printing of functional electronic materials may provide a new route to low-cost fabrication of integrated circuits. However, to be useful it must allow continuous manufacturing of all circuit components by successive solution deposition and printing steps in the same environment. We demonstrate direct inkjet printing of complete transistor circuits, including via-hole interconnections based on solution-processed polymer conductors, insulators, and self-organizing semiconductors. We show that the use of substrate surface energy patterning to direct the flow of water-based conducting polymer inkjet droplets enables high-resolution definition of practical channel lengths of 5 micrometers. High mobilities of 0.02 square centimeters per volt second and on-off current switching ratios of 10 5 were achieved.

3,190 citations