G.D. Janaki Ram

Bio: G.D. Janaki Ram is an academic researcher from Indian Institute of Technology Madras. The author has contributed to research in topics: Welding & Ultimate tensile strength. The author has an hindex of 33, co-authored 109 publications receiving 3562 citations. Previous affiliations of G.D. Janaki Ram include Indian Institute of Technology, Hyderabad & University of New Brunswick.

Control of Laves phase in Inconel 718 GTA welds with current pulsing

Abstract: The presence of Nb rich Laves phase in Inconel 718 weld fusion zones is known to be detrimental to weld mechanical properties. In the present study, an attempt was made to control the formation of Laves phase in alloy 718 gas tungsten arc welds using pulsed current. Welds were produced in 2 mm thick sheets of the alloy with constant current and pulsed current and were subjected to post-weld solution treatment at 980°C followed by aging. Detailed microstructural studies and tensile tests at 650°C were conducted. The results show that the use of current pulsing (i) refines the fusion zone microstructure, (ii) reduces the amount of Laves phase and exerts a favourable influence on its morphology and (iii) improves the response of the fusion zone to post-weld heat treatment and weld tensile properties.

Use of ultrasonic consolidation for fabrication of multi‐material structures

Abstract: Purpose – Ultrasonic consolidation (UC) is a novel additive manufacturing process developed for fabrication of metallic parts from foils. While the process has been well demonstrated for part fabrication in Al alloy 3003, some of the potential strengths of the process have not been fully explored. One of them is its suitability for fabrication of parts in multi‐materials. This work aims to examine this aspect.Design/methodology/approach – Multi‐material UC experiments were conducted using Al alloy 3003 foils as the bulk part material together with a number of engineering materials (foils of Al‐Cu alloy 2024, Ni‐base alloy Inconel 600® AISI 347 stainless steel, and others). Deposit microstructures were studied to evaluate bonding between various materials.Findings – It was found that most of the materials investigated can be successfully bonded to alloy Al 3003 and vice versa. SiC fibers and stainless wire meshes were successfully embedded in an Al 3003 matrix. The results suggest that the UC process is qu...

Phd by thesis

Abstract: Deposits of clastic carbonate-dominated (calciclastic) sedimentary slope systems in the rock record have been identified mostly as linearly-consistent carbonate apron deposits, even though most ancient clastic carbonate slope deposits fit the submarine fan systems better. Calciclastic submarine fans are consequently rarely described and are poorly understood. Subsequently, very little is known especially in mud-dominated calciclastic submarine fan systems. Presented in this study are a sedimentological core and petrographic characterisation of samples from eleven boreholes from the Lower Carboniferous of Bowland Basin (Northwest England) that reveals a >250 m thick calciturbidite complex deposited in a calciclastic submarine fan setting. Seven facies are recognised from core and thin section characterisation and are grouped into three carbonate turbidite sequences. They include: 1) Calciturbidites, comprising mostly of highto low-density, wavy-laminated bioclast-rich facies; 2) low-density densite mudstones which are characterised by planar laminated and unlaminated muddominated facies; and 3) Calcidebrites which are muddy or hyper-concentrated debrisflow deposits occurring as poorly-sorted, chaotic, mud-supported floatstones. These

The status, challenges, and future of additive manufacturing in engineering

Abstract: Additive manufacturing (AM) is poised to bring about a revolution in the way products are designed, manufactured, and distributed to end users. This technology has gained significant academic as well as industry interest due to its ability to create complex geometries with customizable material properties. AM has also inspired the development of the maker movement by democratizing design and manufacturing. Due to the rapid proliferation of a wide variety of technologies associated with AM, there is a lack of a comprehensive set of design principles, manufacturing guidelines, and standardization of best practices. These challenges are compounded by the fact that advancements in multiple technologies (for example materials processing, topology optimization) generate a "positive feedback loop" effect in advancing AM. In order to advance research interest and investment in AM technologies, some fundamental questions and trends about the dependencies existing in these avenues need highlighting. The goal of our review paper is to organize this body of knowledge surrounding AM, and present current barriers, findings, and future trends significantly to the researchers. We also discuss fundamental attributes of AM processes, evolution of the AM industry, and the affordances enabled by the emergence of AM in a variety of areas such as geometry processing, material design, and education. We conclude our paper by pointing out future directions such as the "print-it-all" paradigm, that have the potential to re-imagine current research and spawn completely new avenues for exploration. The fundamental attributes and challenges/barriers of Additive Manufacturing (AM).The evolution of research on AM with a focus on engineering capabilities.The affordances enabled by AM such as geometry, material and tools design.The developments in industry, intellectual property, and education-related aspects.The important future trends of AM technologies.

The metallurgy and processing science of metal additive manufacturing

Abstract: Additive manufacturing (AM), widely known as 3D printing, is a method of manufacturing that forms parts from powder, wire or sheets in a process that proceeds layer by layer. Many techniques (using many different names) have been developed to accomplish this via melting or solid-state joining. In this review, these techniques for producing metal parts are explored, with a focus on the science of metal AM: processing defects, heat transfer, solidification, solid-state precipitation, mechanical properties and post-processing metallurgy. The various metal AM techniques are compared, with analysis of the strengths and limitations of each. Only a few alloys have been developed for commercial production, but recent efforts are presented as a path for the ongoing development of new materials for AM processes.