G. Krabbes

Bio: G. Krabbes is an academic researcher from Leibniz Association. The author has contributed to research in topics: Flux pinning & Magnetization. The author has an hindex of 25, co-authored 96 publications receiving 2054 citations.

Superconducting bulk magnets: Very high trapped fields and cracking

Abstract: Improved trapped fields are reported for bulk melt-textured YBa2Cu3O7−δ (YBCO) material in the temperature range between 20 and 50 K. Trapped fields up to 12.2 T were obtained at 22 K on the surface of single YBCO disks (with Ag and Zn additions). In YBCO minimagnets, maximum trapped fields of 16 T (at 24 K) and of 11,2 T (at 47 K) were achieved using (Zn+Ag) and Zn additions, respectively. In all cases, the YBCO disks were encapsulated in steel tubes in order to reinforce the material against the large tensile stress acting during the magnetizing process and to avoid cracking. We observed cracking not only during the magnetizing process, but also as a consequence of flux jumps due to thermomagnetic instabilities in the temperature range betweeen 20 and 30 K.

Trapped magnetic fields larger than 14 T in bulk YBa2Cu3O7−x

Abstract: High trapped fields were found in zinc-doped, bulk melt-textured YBa2Cu3O7−x (YBCO) material showing a pronounced peak effect in the field dependence of the critical current density Trapped fields up to 11 T were found at 77 K at the surface of a YBCO disk (diameter 26 mm, height 12 mm) Very high trapped fields up to 1435 T were achieved at 225 K for a YBCO disk pair (diameter 26 mm, height 24 mm) by the addition of silver and using a bandage made of stainless steel The pinning forces and trapped fields obtained in bulk YBCO material are compared with results reported for melt-processed NdBa2Cu3O7−x and SmBa2Cu3O7−x

Zn doping of YBa2Cu3O7 in melt textured materials: peak effect and high trapped fields

Abstract: The previously introduced modified melt crystallization process (MMCP) has been applied to prepare single grain YBCO bulk material with Zn partially substituting for Cu. Hole doping was controlled by an appropriate oxidizing treatment of the as-grown bulk. A field induced pinning was indicated by a well pronounced peak of the critical current density jc in the jc vs. H relationship for the maximal oxidized (overdoped) material containing Zn, whereas pure overdoped YBCO shows no peak effect. The peak effect for Zn-doped YBCO appearing for T=77 K at a relatively high field of about 3 T can be attributed to pair breaking by locally induced magnetic moments due to in plane Zn for Cu substitution. Besides high quality of the bulk YBCO, the peak effect is the reason for the trapped field as large as 1.12 T at 77 K in the cylinder of only 25 mm in diameter.

Multi-seeded melt crystallization of YBCO bulk material for cryogenic applications

Abstract: YBCO bulk materials were crystallized by a multi-seeded melt growth process. Up to four biaxial oriented Sm-123 seeds were placed on the top of rectangular shaped YBCO bars (up to ). The oriented grown single grains are joined by partially coherent grain boundaries with an improved current transport capability and high levitation forces with overall values of 55-65 N. Segregation of nonsuperconducting rest melt and microcracks limit the current transport across the grain boundary.

Characterization techniques for nanoparticles: comparison and complementarity upon studying nanoparticle properties

Abstract: Nanostructures have attracted huge interest as a rapidly growing class of materials for many applications. Several techniques have been used to characterize the size, crystal structure, elemental composition and a variety of other physical properties of nanoparticles. In several cases, there are physical properties that can be evaluated by more than one technique. Different strengths and limitations of each technique complicate the choice of the most suitable method, while often a combinatorial characterization approach is needed. In addition, given that the significance of nanoparticles in basic research and applications is constantly increasing, it is necessary that researchers from separate fields overcome the challenges in the reproducible and reliable characterization of nanomaterials, after their synthesis and further process (e.g. annealing) stages. The principal objective of this review is to summarize the present knowledge on the use, advances, advantages and weaknesses of a large number of experimental techniques that are available for the characterization of nanoparticles. Different characterization techniques are classified according to the concept/group of the technique used, the information they can provide, or the materials that they are destined for. We describe the main characteristics of the techniques and their operation principles and we give various examples of their use, presenting them in a comparative mode, when possible, in relation to the property studied in each case.

High-temperature superconductor bulk magnets that can trap magnetic fields of over 17 tesla at 29 K

Abstract: Large-grain high-temperature superconductors of the form RE-Ba-Cu-O (where RE is a rare-earth element) can trap magnetic fields of several tesla at low temperatures, and so can be used for permanent magnet applications. The magnitude of the trapped field is proportional to the critical current density and the volume of the superconductor. Various potential engineering applications for such magnets have emerged, and some have already been commercialized. However, the range of applications is limited by poor mechanical stability and low thermal conductivity of the bulk superconductors; RE-Ba-Cu-O magnets have been found to fracture during high-field activation, owing to magnetic pressure. Here we present a post-fabrication treatment that improves the mechanical properties as well as thermal conductivity of a bulk Y-Ba-Cu-O magnet, thereby increasing its field-trapping capacity. First, resin impregnation and wrapping the materials in carbon fibre improves the mechanical properties. Second, a small hole drilled into the centre of the magnet allows impregnation of Bi-Pb-Sn-Cd alloy into the superconductor and inclusion of an aluminium wire support, which results in a significant enhancement of thermal stability and internal mechanical strength. As a result, 17.24 T could be trapped, without fracturing, in a bulk Y-Ba-Cu-O sample of 2.65 cm diameter at 29 K.

A trapped field of 17.6 T in melt-processed, bulk Gd-Ba-Cu-O reinforced with shrink-fit steel

Abstract: The ability of large-grain (RE)Ba2Cu3O7−δ ((RE)BCO; RE = rare earth) bulk superconductors to trap magnetic fields is determined by their critical current. With high trapped fields, however, bulk samples are subject to a relatively large Lorentz force, and their performance is limited primarily by their tensile strength. Consequently, sample reinforcement is the key to performance improvement in these technologically important materials. In this work, we report a trapped field of 17.6 T, the largest reported to date, in a stack of two silver-doped GdBCO superconducting bulk samples, each 25 mm in diameter, fabricated by top-seeded melt growth and reinforced with shrink-fit stainless steel. This sample preparation technique has the advantage of being relatively straightforward and inexpensive to implement, and offers the prospect of easy access to portable, high magnetic fields without any requirement for a sustaining current source.

Extrinsic magnetotransport phenomena in ferromagnetic oxides

Abstract: Magnetic oxides show a variety of extrinsic magnetotransport phenomena: grain-boundary, tunnelling and domain-wall magnetoresistance. In view of these phenomena the role of some magnetic oxides is outstanding: these are believed to be half-metallic having only one spin-subband at the Fermi level. These fully spin-polarized oxides have great potential for applications in spin-electronic devices and have, accordingly, attracted intense research activity in recent years. This review is focused on extrinsic magnetotransport effects in ferromagnetic oxides. It consists of two parts; the second part is devoted to an overview of experimental data and theoretical models for extrinsic magnetotransport phenomena. Here a critical discussion of domain-wall scattering is given. Results on surface and interfacial magnetism in oxides are presented. Spin-polarized tunnelling in ferromagnetic junctions is reviewed and grain-boundary magnetoresistance is interpreted within a model of spin-polarized tunnelling through natural oxide barriers. The situation in ferromagnetic oxides is compared with data and models for conventional ferromagnets. The first part of the review summarizes basic material properties, especially data on the spin polarization and evidence for half-metallicity. Furthermore, intrinsic conduction mechanisms are discussed. An outlook on the further development of oxide spin-electronics concludes this review.

Superconductor bearings, flywheels and transportation

Abstract: This paper describes the present status of high temperature superconductors (HTS) and of bulk superconducting magnet devices, their use in bearings, in flywheel energy storage systems (FESS) and linear transport magnetic levitation (Maglev) systems. We report and review the concepts of multi-seeded REBCO bulk superconductor fabrication. The multi-grain bulks increase the averaged trapped magnetic flux density up to 40% compared to single-grain assembly in large-scale applications. HTS magnetic bearings with permanent magnet (PM) excitation were studied and scaled up to maximum forces of 10 kN axially and 4.5 kN radially. We examine the technology of the high-gradient magnetic bearing concept and verify it experimentally. A large HTS bearing is tested for stabilizing a 600 kg rotor of a 5 kWh/250 kW flywheel system. The flywheel rotor tests show the requirement for additional damping. Our compact flywheel system is compared with similar HTS–FESS projects. A small-scale compact YBCO bearing with in situ Stirling cryocooler is constructed and investigated for mobile applications. Next we show a successfully developed modular linear Maglev system for magnetic train operation. Each module levitates 0.25t at 10 mm distance during one-day operation without refilling LN2. More than 30 vacuum cryostats containing multi-seeded YBCO blocks are fabricated and are tested now in Germany, China and Brazil.