Gary E. Betts

Bio: Gary E. Betts is an academic researcher from Massachusetts Institute of Technology. The author has contributed to research in topics: Noise figure & Optical modulator. The author has an hindex of 24, co-authored 69 publications receiving 2675 citations.

Limits on the performance of RF-over-fiber links and their impact on device design

Abstract: This paper is divided into two major parts. Following a brief introduction that establishes some definitions and assumptions, Section II updates our earlier study on the limits of the RF performance of optical links. Section III reviews progress since our 1997 review paper in the development of devices enabling link performance closer to these limits, including (but not limited to): 1) cascade lasers that permit broad-band direct modulation links with gain >0 dB; 2) injection-locked edge- and surface-emitting lasers at 1300 and 1550 nm with modulation frequency responses as great as 40 GHz; 3) modulators with improved performance, especially electroabsorption modulators that now have switching voltages as low as 0.36 V, or handle optical powers as great as 60 mW, or have bandwidths as great as 50 GHz (but not all three of these in one device yet); and 4) high-speed photodetectors with high saturation currents, e.g., a 20-GHz device with a saturation current of 90 mA and a 55-GHz device with saturation at 50 mA. We conclude in Section IV by summarizing the component developments necessary for higher performance RF-over-fiber links, i.e.: 1) semiconductor lasers (for direct modulation) that have higher slope efficiency and bandwidth and lower relative intensity noise (RIN) at reasonable bias current levels; 2) continuous wave (CW) lasers (for external modulation) with higher fiber-coupled power and lower RIN; 3) higher frequency lower loss external modulators with more linear transfer functions and lower V/sub /spl pi// that can withstand larger CW optical powers; and 4) photodetectors with higher responsivity and bandwidth that respond linearly even when illuminated by greater average optical powers.

Optically sampled analog-to-digital converters

Abstract: Optically sampled analog-to-digital converters (ADCs) combine optical sampling with electronic quantization to enhance the performance of electronic ADCs. In this paper, we review the prior and current work in this field, and then describe our efforts to develop and extend the bandwidth of a linearized sampling technique referred to as phase-encoded optical sampling. The technique uses a dual-output electrooptic sampling transducer to achieve both high linearity and 60-dB suppression of laser amplitude noise. The bandwidth of the technique is extended by optically distributing the post-sampling pulses to an array of time-interleaved electronic quantizers. We report on the performance of a 505-MS/s (megasample per second) optically sampled ADC that includes high-extinction LiNbO/sub 3/ 1-to-8 optical time-division demultiplexers. Initial characterization of the 505-MS/s system reveals a maximum signal-to-noise ratio of 51 dB (8.2 bits) and a spur-free dynamic range of 61 dB. The performance of the present system is limited by electronic quantizer noise, photodiode saturation, and preliminary calibration procedures. None of these fundamentally limit this sampling approach, which should enable multigigahertz converters with 12-b resolution. A signal-to-noise analysis of the phase-encoded sampling technique shows good agreement with measured data from the 505-MS/s system.

Corrections to "Limits on the Performance of RF-Over-Fiber Links and Their Impact on Device Design"

Abstract: The authors correct an error in their original article (see ibid., vol.54, no.2, p.906-20, Feb. 2006).

An analytic and experimental comparison of direct and external modulation in analog fiber-optic links

Abstract: Analytic lumped-element small-signal models of directly and externally modulated analog fiber-optic links are derived. Incremental modulation efficiency is defined and used to compare the performances of these modulation techniques. In experiments to optimize link RF-to-RF gain and noise figure, the measurements obtained agreed with calculations to within approximately=1 dB. The externally modulated link was operated with two different impedance matching circuits. With a low-pass match the bandwidth was 150 MHz, and the link transducer gain was 1 dB; with a bandpass match the bandwidth was 22 MHz, the link transducer gain was 11 dB, and the noise figure was 6 dB. The directly modulated link was operated with a low-pass match. In this case, the bandwidth was 1 GHz, the link transducer gain was -14 dB, and the noise figure was 33 dB. These experimental results were achieved with no amplification,. >

Direct-detection analog optical links

Abstract: We review state-of-the-art intensity-modulation direct-detection (IMDD) analog optical links, focusing on advances since 1990. We contrast direct and external modulation with respect to gain, noise figure, and dynamic-range performance.

Microwave photonics combines two worlds

Abstract: Microwave photonics, which brings together the worlds of radiofrequency engineering and optoelectronics, has attracted great interest from both the research community and the commercial sector over the past 30 years and is set to have a bright future. The technology makes it possible to have functions in microwave systems that are complex or even not directly possible in the radiofrequency domain and also creates new opportunities for telecommunication networks. Here we introduce the technology to the photonics community and summarize recent research and important applications.

Microwave photonics

Abstract: An overview of analog microwave photonics will be presented. The performance requirements for externally-modulated analog microwave photonic links will be reviewed with specific emphasis placed on modulator efficiency, laser noise, detected photocurrent, and link linearity.

A review of lithium niobate modulators for fiber-optic communications systems

Abstract: The current status of lithium-niobate external-modulator technology is reviewed with emphasis on design, fabrication, system requirements, performance, and reliability. The technology meets the performance and reliability requirements of current 2.5-, 10-, and 40-Gb/s digital communication systems, as well as CATV analog systems. The current trend in device topology is toward higher data rates and increased levels of integration. In particular, multiple high-speed modulation functions, such as 10-Gb/s return-to-zero pulse generation plus data modulation, have been achieved in a single device.

A tutorial on microwave photonic filters

Abstract: Microwave photonic filters are photonic subsystems designed with the aim of carrying equivalent tasks to those of an ordinary microwave filter within a radio frequency (RF) system or link, bringing supplementary advantages inherent to photonics such as low loss, high bandwidth, immunity to electromagnetic interference (EMI), tunability, and reconfigurability. There is an increasing interest in this subject since, on one hand, emerging broadband wireless access networks and standards spanning from universal mobile telecommunications system (UMTS) to fixed access picocellular networks and including wireless local area network (WLAN), World Interoperability for Microwave Access, Inc. (WIMAX), local multipoint distribution service (LMDS), etc., require an increase in capacity by reducing the coverage area. An enabling technology to obtain this objective is based on radio-over-fiber (RoF) systems where signal processing is carried at a central office to where signals are carried from inexpensive remote antenna units (RAUs). On the other hand, microwave photonic filters can find applications in specialized fields such as radar and photonic beamsteering of phased-arrayed antennas, where dynamical reconfiguration is an added value. This paper provides a tutorial introduction of this subject to the reader not working directly in the field but interested in getting an overall introduction of the subject and also to the researcher wishing to get a comprehensive background before working on the subject.

Low (Sub-1-Volt) Halfwave Voltage Polymeric Electro-optic Modulators Achieved by Controlling Chromophore Shape

Abstract: Electro-optic (EO) modulators encode electrical signals onto fiber optic transmissions. High drive voltages limit gain and noise levels. Typical polymeric and lithium niobate modulators operate with halfwave voltages of 5 volts. Sterically modified organic chromophores have been used to reduce the attenuation of electric field poling-induced electro-optic activity caused by strong intermolecular electrostatic interactions. Such modified chromophores, incorporated into polymer hosts, were used to fabricate EO modulators with halfwave voltages of 0.8 volts (at a telecommunications wavelength of 1318 nanometers) and to achieve a halfwave voltage-interaction length product of 2.2 volt-centimeters. Optical push-pull poling and driving were also used to reduce halfwave voltage. This study, together with recent demonstrations of exceptional bandwidths (more than 110 gigahertz) and ease of integration (with very large scale integration semiconductor circuitry and ultra-low-loss passive optical circuitry) demonstrates the potential of polymeric materials for next generation telecommunications, information processing, and radio frequency distribution.