Goksen G. Yaralioglu

Bio: Goksen G. Yaralioglu is an academic researcher from Özyeğin University. The author has contributed to research in topics: Capacitive micromachined ultrasonic transducers & Ultrasonic sensor. The author has an hindex of 37, co-authored 92 publications receiving 4442 citations. Previous affiliations of Goksen G. Yaralioglu include InvenSense & Stanford University.

Automated parallel high-speed atomic force microscopy

Abstract: An expandable system has been developed to operate multiple probes for the atomic force microscope in parallel at high speeds. The combined improvements from parallelism and enhanced tip speed in this system represent an increase in throughput by over two orders of magnitude. A modular cantilever design has been replicated to produce an array of 50 cantilevers with a 200 μm pitch. This design contains a dedicated integrated sensor and integrated actuator where the cells can be repeated indefinitely. Electrical shielding within the array virtually eliminates coupling between the actuators and sensors. The reduced coupling simplifies the control electronics, facilitating the design of a computer system to automate the parallel high-speed arrays. This automated system has been applied to four cantilevers within the array of 50 cantilevers, with a 20 kHz bandwidth and a noise level of less than 50 A. For typical samples, this bandwidth allows us to scan the probes at 4 mm/s.

Capacitive Micromachined Ultrasonic Transducers: Theory and Technology

Abstract: Capacitive micromachined ultrasonic transducers ~CMUTs!, introduced about a decade ago, have been shown to be a good alternative to conventional piezoelectric transducers in various aspects, such as sensitivity, transduction efficiency, and bandwidth. In this paper, we discuss the principles of capacitive transducer operation that underlie these aspects. Many of the key features of capacitive ultrasonic transducers are enabled with micromachining technology. Micromachining allows us to miniaturize device dimensions and produce capacitive transducers that perform comparably to their piezoelectric counterparts. The fabrication process is described briefly, and the performance of the CMUT transducers is evaluated by demonstrating characterization results. It is shown that the transduction efficiency as defined by the electromechanical coupling coefficient can be close to unity with proper device design and operating voltage. It is also shown that CMUTs provide large bandwidth ~123% fractional bandwidth! in immersion applications which translate into high temporal and axial resolution. Finally, the feasibility of using CMUTs is demonstrated by showing imaging examples in air and in immersion.

Ultrasonic Mixing in Microfluidic Channels Using Integrated Transducers

Abstract: This paper presents a microfluidic mixer that uses acoustic stirring created by ultrasonic waves. The ultrasound is introduced into the channel by integrated piezoelectric transducers. The transducers are made of a zinc oxide thin film, which is deposited on the bottom surface of a quartz substrate. The poly(dimethylsiloxane) channel is aligned to the transducers on the top surface of the substrate. The transducers are designed for operation around 450 MHz. The main mechanism of the mixing is the acoustic stirring of the fluid perpendicular to the flow direction. The radiation pressure that is generated by the transducer causes the stirring inside the microfluidic channel. The performance of the mixer is characterized by mixing phenolphthalein solution and sodium hydroxide dissolved in ethyl alcohol. Flow rates on the order of 1−100 μL/min are used. The transducers are driven by 1.2 Vrms sinusoidal voltages at 450 MHz.

High-speed tapping mode imaging with active Q control for atomic force microscopy

Abstract: The speed of tapping mode imaging with the atomic force microscope (AFM) has been increased by over an order of magnitude. The enhanced operation is achieved by (1) increasing the instrument’s mechanical bandwidth and (2) actively controlling the cantilever’s dynamics. The instrument’s mechanical bandwidth is increased by an order of magnitude by replacing the piezotube z-axis actuator with an integrated zinc oxide (ZnO) piezoelectric cantilever. The cantilever’s dynamics are optimized for high-speed operation by actively damping the quality factor (Q) of the cantilever. Active damping allows the amplitude of the oscillating cantilever to respond to topography changes more quickly. With these two advancements, 80μm×80 μm high-speed tapping mode images have been obtained with a scan frequency of 15 Hz. This corresponds to a tip velocity of 2.4 mm/s.

Calculation and measurement of electromechanical coupling coefficient of capacitive micromachined ultrasonic transducers

Abstract: The electromechanical coupling coefficient is an important figure of merit of ultrasonic transducers. The transducer bandwidth is determined by the electromechanical coupling efficiency. The coupling coefficient is, by definition, the ratio of delivered mechanical energy to the stored total energy in the transducer. In this paper, we present the calculation and measurement of coupling coefficient for capacitive micromachined ultrasonic transducers (CMUTs). The finite element method (FEM) is used for our calculations, and the FEM results are compared with the analytical results obtained with parallel plate approximation. The effect of series and parallel capacitances in the CMUT also is investigated. The FEM calculations of the CMUT indicate that the electromechanical coupling coefficient is independent of any series capacitance that may exist in the structure. The series capacitance, however, alters the collapse voltage of the membrane. The parallel parasitic capacitance that may exist in a CMUT or is external to the transducer reduces the coupling coefficient at a given bias voltage. At the collapse, regardless of the parasitics, the coupling coefficient reaches unity. Our experimental measurements confirm a coupling coefficient of 0.85 before collapse, and measurements are in agreement with theory.

Micromixers?a review

Abstract: This review reports the progress on the recent development of micromixers. The review first presents the different micromixer types and designs. Micromixers in this review are categorized as passive micromixers and active micromixers. Due to the simple fabrication technology and the easy implementation in a complex microfluidic system, passive micromixers will be the focus of this review. Next, the review discusses the operation points of the micromixers based on characteristic dimensionless numbers such as Reynolds number Re, Peclet number Pe, and in dynamic cases the Strouhal number St. The fabrication technologies for different mixer types are also analysed. Quantification techniques for evaluation of the performance of micromixers are discussed. Finally, the review addresses typical applications of micromixers.

A Survey of Control Issues in Nanopositioning

Abstract: Nanotechnology is the science of understanding matter and the control of matter at dimensions of 100 nm or less. Encompassing nanoscale science, engineering, and technology, nanotechnology involves imaging, measuring, modeling, and manipulation of matter at this level of precision. An important aspect of research in nanotechnology involves precision control and manipulation of devices and materials at a nanoscale, i.e., nanopositioning. Nanopositioners are precision mechatronic systems designed to move objects over a small range with a resolution down to a fraction of an atomic diameter. The desired attributes of a nanopositioner are extremely high resolution, accuracy, stability, and fast response. The key to successful nanopositioning is accurate position sensing and feedback control of the motion. This paper presents an overview of nanopositioning technologies and devices emphasizing the key role of advanced control techniques in improving precision, accuracy, and speed of operation of these systems.

Microscale acoustofluidics: Microfluidics driven via acoustics and ultrasonics

Abstract: This article reviews acoustic microfiuidics: the use of acoustic fields, principally ultrasonics, for application in microfiuidics. Although acoustics is a classical field, its promising, and indeed perplexing, capabilities in powerfully manipulating both fluids and particles within those fluids on the microscale to nanoscale has revived interest in it. The bewildering state of the literature and ample jargon from decades of research is reorganized and presented in the context of models derived from first principles. This hopefully will make the area accessible for researchers with experience in materials science, fluid mechanics, or dynamics. The abundance of interesting phenomena arising from nonlinear interactions in ultrasound that easily appear at these small scales is considered, especially in surface acoustic wave devices that are simple to fabricate with planar lithography techniques common in microfluidics, along with the many applications in microfluidics and nanofluidics that appear through the literature.

Microfluidic Mixing: A Review

Abstract: The aim of microfluidic mixing is to achieve a thorough and rapid mixing of multiple samples in microscale devices. In such devices, sample mixing is essentially achieved by enhancing the diffusion effect between the different species flows. Broadly speaking, microfluidic mixing schemes can be categorized as either “active”, where an external energy force is applied to perturb the sample species, or “passive”, where the contact area and contact time of the species samples are increased through specially-designed microchannel configurations. Many mixers have been proposed to facilitate this task over the past 10 years. Accordingly, this paper commences by providing a high level overview of the field of microfluidic mixing devices before describing some of the more significant proposals for active and passive mixers.

Applications of dip-pen nanolithography.

Abstract: The ability to tailor the chemical composition and structure of a surface at the sub-100-nm length scale is important for studying topics ranging from molecular electronics to materials assembly, and for investigating biological recognition at the single biomolecule level. Dip-pen nanolithography (DPN) is a scanning probe microscopy-based nanofabrication technique that uniquely combines direct-write soft-matter compatibility with the high resolution and registry of atomic force microscopy (AFM), which makes it a powerful tool for depositing soft and hard materials, in the form of stable and functional architectures, on a variety of surfaces. The technology is accessible to any researcher who can operate an AFM instrument and is now used by more than 200 laboratories throughout the world. This article introduces DPN and reviews the rapid growth of the field of DPN-enabled research and applications over the past several years.