Guna S Selvaduray

Bio: Guna S Selvaduray is an academic researcher from San Jose State University. The author has contributed to research in topics: Electropolishing & Fusible alloy. The author has an hindex of 10, co-authored 35 publications receiving 2452 citations.

Lead-free Solders in Microelectronics

Abstract: Practically all microelectronic assemblies in use today utilize Pb–Sn solders for interconnection. With the advent of chip scale packaging technologies, the usage of solder connections has increased. The most widely used Pb–Sn solder has the eutectic composition. Emerging environmental regulations worldwide, most notably in Europe and Japan, have targeted the elimination of Pb usage in electronic assemblies, due to the inherent toxicity of Pb. This has made the search for suitable “Pb-free” solders an important issue for microelectronics assembly. Approximately 70 Pb-free solder alloy compositions have been proposed thus far. There is a general lack of engineering information, and there is also significant disparity in the information available on these alloys. The issues involved can be divided into two broad categories: manufacturing and reliability/performance. A major factor affecting alloy selection is the melting point of the alloy, since this will have a major impact on the other polymeric materials used in microelectronic assembly and encapsulation. Other important manufacturing issues are cost, availability, and wetting characteristics. Reliability related properties include mechanical strength, fatigue resistance, coefficient of thermal expansion and intermetallic compound formation. The data available in the open literature have been reviewed and are summarized in this paper. Where data were not available, such as for corrosion and oxidation resistance, chemical thermodynamics was used to develop this information. While a formal alloy selection decision analysis methodology has not been developed, less formal approaches indicate that Sn-rich alloys will be the Pb-free solder alloys of choice, with three to four alloys being identified for each of the different applications. Research on this topic continues at the present time at a vigorous pace, in view of the imminence of the issue.

Effects of surface treatment on the surface chemistry of NiTi alloy for biomedical applications

Abstract: Alloys of NiTi have gained popularity in biomedical applications; however, Ni is known to cause toxic and allergic reactions in the body, and concerns have been expressed regarding the material's biocompatibility. In this study, coupons of equiatomic NiTi were prepared by four methods, namely, mechanically polishing to a mirror finish, electropolishing, chemical etching and argon plasma etching, to produce various levels of roughness, and then examined by atomic force microscopy (AFM), XPS and AES. The resulting surface chemistry depended upon the method of preparation and was found not to be a function of surface roughness. The mechanically polished samples, although having the smoothest surface, showed the highest level of Ni in the near-surface region. The other preparation methods produced surfaces that were predominantly TiO2, with the electropolished surfaces showing the next smoothest surface and the least Ni in the near-surface region. The correlation between method of preparation, surface roughness and surface chemistry may be important in the preparation of NiTi for biomedical applications. © 1998 John Wiley & Sons, Ltd.

The Effects of Cold Work and Heat Treatment on the Properties of Nitinol Wire

Abstract: The successful medical application of Nitinol requires precise control of its transformational and mechanical properties. In this study the effects of heat treatments at 300-550°C for 2-180 minutes on Ti-50.8at%Ni wire with 30% and 50% initial cold work were investigated. Transformational and mechanical properties were characterized through the BFR technique and tensile testing. Thermally activated precipitation and annealing processes were observed. Annealing processes tended to increase the maximum slope of the BFR curves. The R-phase was observed with greater frequency and prominence in the 50% cold-worked wire after heat treatment. The general trends in Af are summarized in two TTT diagrams; both illustrate a maximum precipitation rate of Ni4Ti3 at 400-450°C. The trends in tensile properties are outlined for all heat treatment conditions. Recovery processes occurred at all temperatures. The onset of recrystallization occurred at approximately 450°C for both wires.

Effect of CO2 on the processing of Y–Ba–Cu–O superconductors

Abstract: The superconducting properties of YBa2Cu3O6+x reacted with various known ratios of O2/CO2 gas mixtures during sintering at different temperatures were studied. Jc was found to decrease drastically upon reaction with CO2, becoming zero at certain CO2 activities. The stability region for the 123 superconductor, as a function of CO2 activity and temperature, was empirically formulated as follows: log pCO2 < (−45,000)/T + 33.4. The grain boundaries in sintered samples with Jc = 0 were investigated with HRTEM in conjunction with EDS. Two distinct types of grain boundaries were observed. Approximately 10% of the grain boundaries were wet by a thin layer of a second phase, deduced to be BaCuO2. The remaining boundaries were sharp grain boundaries. The grain structure near the sharp grain boundaries was tetragonal. These two types of grain boundaries are thought to be responsible for Jc being zero.

Six cases of reliability study of Pb-free solder joints in electronic packaging technology

Abstract: Solder is widely used to connect chips to their packaging substrates in flip chip technology as well as in surface mount technology. At present, the electronic packaging industry is actively searching for Pb-free solders due to environmental concern of Pb-based solders. Concerning the reliability of Pb-free solders, some electronic companies are reluctant to adopt them into their high-end products. Hence, a review of the reliability behavior of Pb-free solders is timely. We use the format of “case study” to review six reliability problems of Pb-free solders in electronic packaging technology. We conducted analysis of these cases on the basis of thermodynamic driving force, time-dependent kinetic processes, and morphology and microstructure changes. We made a direct comparison to the similar problem in SnPb solder whenever it is available. Specifically, we reviewed: (1) interfacial reactions between Pb-free solder and thick metalliztion of bond-pad on the substrate-side, (2) interfacial reactions between Pb-free solder and thin-film under-bump metallization on the chip-side, (3) the growth of a layered intermetallic compound (IMC) by ripening in solid state aging of solder joints, (4) a long range interaction between chip-side and substrate-side metallizations across a solder joint, (5) electromigration in flip chip solder joints, and finally (6) Sn whisker growth on Pb-free finish on Cu leadframe. Perhaps, these cases may serve as helpful references to the understanding of other reliability behaviors of Pb-free solders.

Transferring lead-free piezoelectric ceramics into application

Abstract: After twenty years of partly quiet and ten years of partly enthusiastic research into lead-free piezoceramics there are now clear prospects for transfer into applications in some areas. This mimics prior research into eliminating lead from other technologies that resulted in restricted lead use in batteries and dwindling use in other applications. A figure of merit analysis for key devices is presented and used to contrast lead-containing and lead-free piezoceramics. A number of existing applications emerge, where the usage of lead-free piezoceramics may be envisaged in the near future. A sufficient transition period to ensure reliability, however, is required. The use of lead-free piezoceramics for demanding applications with high reliability, displacements and frequency as well as a wide temperature range appears to remain in the distant future. New devices are outlined, where the figure of merit suggests skipping lead-containing piezoceramics altogether. Suggestions for the next pertinent research requirements are provided.

Hands-on, simulated, and remote laboratories: A comparative literature review

Abstract: Laboratory-based courses play a critical role in scientific education. Automation is changing the nature of these laboratories, and there is a long-running debate about the value of hands-on versus simulated laboratories. In addition, the introduction of remote laboratories adds a third category to the debate. Through a review of the literature related to these labs in education, the authors draw several conclusions about the state of current research. The debate over different technologies is confounded by the use of different educational objectives as criteria for judging the laboratories: Hands-on advocates emphasize design skills, while remote lab advocates focus on conceptual understanding. We observe that the boundaries among the three labs are blurred in the sense that most laboratories are mediated by computers, and that the psychology of presence may be as important as technology. We also discuss areas for future research.

Biomedical Applications of Silver Nanoparticles: An Up-to-Date Overview

Abstract: During the past few years, silver nanoparticles (AgNPs) became one of the most investigated and explored nanotechnology-derived nanostructures, given the fact that nanosilver-based materials proved to have interesting, challenging, and promising characteristics suitable for various biomedical applications. Among modern biomedical potential of AgNPs, tremendous interest is oriented toward the therapeutically enhanced personalized healthcare practice. AgNPs proved to have genuine features and impressive potential for the development of novel antimicrobial agents, drug-delivery formulations, detection and diagnosis platforms, biomaterial and medical device coatings, tissue restoration and regeneration materials, complex healthcare condition strategies, and performance-enhanced therapeutic alternatives. Given the impressive biomedical-related potential applications of AgNPs, impressive efforts were undertaken on understanding the intricate mechanisms of their biological interactions and possible toxic effects. Within this review, we focused on the latest data regarding the biomedical use of AgNP-based nanostructures, including aspects related to their potential toxicity, unique physiochemical properties, and biofunctional behaviors, discussing herein the intrinsic anti-inflammatory, antibacterial, antiviral, and antifungal activities of silver-based nanostructures.

Recent advances of conductive adhesives as a lead-free alternative in electronic packaging: Materials, processing, reliability and applications

Abstract: Tin–lead solder alloys are widely used in the electronic industry. They serve as interconnects that provide the conductive path required to achieve connection from one circuit element to another. There are increasing concerns with the use of tin–lead alloy solders in recognition of hazards of using lead. Lead-free solders and electrically conductive adhesives (ECAs) have been considered as the most promising alternatives of tin-lead solder. ECAs consist of a polymeric resin (such as, an epoxy, a silicone, or a polyimide) that provides physical and mechanical properties such as adhesion, mechanical strength, impact strength, and a metal filler (such as, silver, gold, nickel or copper) that conducts electricity. ECAs offer numerous advantages over conventional solder technology, such as environmental friendliness, mild processing conditions (enabling the use of heat-sensitive and low-cost components and substrates), fewer processing steps (reducing processing cost), low stress on the substrates, and fine pitch interconnect capability (enabling the miniaturization of electronic devices). Therefore, conductive adhesives have been used in liquid crystal display (LCD) and smart card applications as an interconnect material and in flip–chip assembly, chip scale package (CSP) and ball grid array (BGA) applications in replacement of solder. However, no currently commercialized ECAs can replace tin–lead metal solders in all applications due to some challenging issues such as lower electrical conductivity, conductivity fatigue (decreased conductivity at elevated temperature and humidity aging or normal use condition) in reliability testing, limited current-carrying capability, and poor impact strength. Considerable research has been conducted recently to study and optimize the performance of ECAs, such as electrical, mechanical and thermal behaviors improvement as well as reliability enhancement under various conditions. This review article will discuss the materials, applications and recent advances of electrically conductive adhesives as an environmental friendly solder replacement in the electronic packaging industry.