Guoxun Sun

Bio: Guoxun Sun is an academic researcher from Shandong University. The author has contributed to research in topics: Boron nitride & Nanosheet. The author has an hindex of 6, co-authored 21 publications receiving 100 citations.

Microstructure and mechanical properties of boron nitride nanosheets-reinforced fused silica composites

Abstract: In order to overcome intrinsic brittleness and poor mechanical properties of fused silica (FS), boron nitride nanosheets (BNNSs) as a novel reinforcement were employed for fabrication of BNNSs/fused silica composites. BNNSs with micron lateral size were homogeneously dispersed with FS powder using a surfactant-free flocculation method and then consolidated by hot pressing. The flexural strength and fracture toughness of the composite with the addition of only 0.5 wt.% BNNSs increased by 53% and 32%, respectively, compared with those of pure FS. However, for higher BNNSs contents the improvement in mechanical properties was limited. Microstructural analyzes have shown that the toughening mechanisms are combinations of the pull-out, crack bridging, and crack deflection mechanisms.

Frictional Characteristics of Atomically-Thin Sheets

Abstract: Thin Friction The rubbing motion between two surfaces is always hindered by friction, which is caused by continuous contacting and attraction between the surfaces. These interactions may only occur over a distance of a few nanometers, but what happens when the interacting materials are only that thick? Lee et al. (p. 76; see the Perspective by Müser and Shakhvorostov) explored the frictional properties of a silicon tip in contact with four atomically thin quasi–two dimensional materials with different electrical properties. For all the materials, the friction was seen to increase as the thickness of the film decreased, both for flakes supported by substrates and for regions placed above holes that formed freely suspended membranes. Placing graphene on mica, to which it strongly adheres, suppressed this trend. For these thin, weakly adhered films, out-of-plane buckling is likely to dominate the frictional response, which leads to this universal behavior. A universal trend is observed for the friction properties of thin films on weakly adhering substrates. Using friction force microscopy, we compared the nanoscale frictional characteristics of atomically thin sheets of graphene, molybdenum disulfide (MoS2), niobium diselenide, and hexagonal boron nitride exfoliated onto a weakly adherent substrate (silicon oxide) to those of their bulk counterparts. Measurements down to single atomic sheets revealed that friction monotonically increased as the number of layers decreased for all four materials. Suspended graphene membranes showed the same trend, but binding the graphene strongly to a mica surface suppressed the trend. Tip-sample adhesion forces were indistinguishable for all thicknesses and substrate arrangements. Both graphene and MoS2 exhibited atomic lattice stick-slip friction, with the thinnest sheets possessing a sliding-length–dependent increase in static friction. These observations, coupled with finite element modeling, suggest that the trend arises from the thinner sheets’ increased susceptibility to out-of-plane elastic deformation. The generality of the results indicates that this may be a universal characteristic of nanoscale friction for atomically thin materials weakly bound to substrates.

Mechanical and tribological properties of nanocomposites incorporated with two-dimensional materials

Abstract: In recent years, attempts to improve the mechanical properties of composites have increased remarkably owing to the inadequate utilization of matrices in demanding technological systems where efficiency, durability, and environmental compatibility are the key requirements. The search for novel materials that can potentially have enhanced mechanical properties continues. Recent studies have demonstrated that two-dimensional (2D) nanomaterials can act as excellent reinforcements because they possess high modulus of elasticity, high strength, and ultralow friction. By incorporating 2D nanomaterials in a composite, 2D nanomaterial-based composites (2DNBCs) have been developed. In view of this, a critical review of recent mechanical and tribological studies based on 2DNBCs has been undertaken. Matrices such as polymers, ceramics, and metals, as well as most of the representative 2D nanomaterial reinforcements such as graphene, boron nitride (BN), molybdenum disulfide (MoS2), and transition metal carbides and nitrides (MXenes) have been included in this review. Their preparation strategies, intrinsic mechanical properties, friction and lubrication performances, strengthening mechanisms, influencing factors, and potential applications have been comprehensively discussed. A brief summary and prospects are given in the final part, which would be useful in designing and fabricating advanced 2D nanocomposites in the future.