Guru Prasad Dinda

Bio: Guru Prasad Dinda is an academic researcher from Wayne State University. The author has contributed to research in topics: Microstructure & Alloy. The author has an hindex of 17, co-authored 44 publications receiving 1899 citations. Previous affiliations of Guru Prasad Dinda include Karlsruhe Institute of Technology & Saarland University.

Laser aided direct metal deposition of Inconel 625 superalloy: Microstructural evolution and thermal stability

Abstract: Direct metal deposition technology is an emerging laser aided manufacturing technology based on a new additive manufacturing principle, which combines laser cladding with rapid prototyping into a solid freeform fabrication process that can be used to manufacture near net shape components from their CAD files. In the present study, direct metal deposition technology was successfully used to fabricate a series of samples of the Ni-based superalloy Inconel 625. A high power CO2 laser was used to create a molten pool on the Inconel 625 substrate into which an Inconel 625 powder stream was delivered to create a 3D object. The structure and properties of the deposits were investigated using optical and scanning electron microscopy, X-ray diffraction and microhardness test. The microstructure has been found to be columnar dendritic in nature, which grew epitaxially from the substrate. The thermal stability of the dendritic morphology was investigated in the temperature range 800–1200 °C. These studies demonstrate that Inconel 625 is an attractive material for laser deposition as all samples produced in this study are free from relevant defects such as cracks, bonding error and porosity.

Fabrication of Ti-6Al-4V Scaffolds by Direct Metal Deposition

Abstract: Direct metal deposition (DMD) is a rapid laser-aided deposition method that can be used to manufacture near-net-shape components from their computer aided design (CAD) files. The method can be used to produce fully dense or porous metallic parts. The Ti-6Al-4V alloy is widely used as an implantable material mainly in the application of orthopedic prostheses because of its high strength, low elastic modulus, excellent corrosion resistance, and good biocompatibility. In the present study, Ti-6Al-4V scaffold has been fabricated by DMD technology for patient specific bone tissue engineering. Good geometry control and surface finish have been achieved. The structure and properties of the scaffolds were investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and tension test. The microstructures of laser-deposited Ti-6Al-4V scaffolds are fine Widmanstatten in nature. The tensile and yield strengths of the as-deposited Ti-6Al-4V were 1163 ± 22 and 1105 ± 19 MPa, respectively, which are quite higher than the ASTM limits (896 and 827 MPa) for Ti-6Al-4V implants. However, the ductility of the as-deposited sample was very low (∼4 pct), which is well below the ASTM limit (10 pct). After an additional heat treatment (sample annealed at 950 °C followed by furnace cooling), both strength (UTS ∼ 1045 ± 16, and YS ∼ 959 ± 12 MPa) and ductility (∼10.5 ± 1 pct) become higher than ASTM limits for medical implants.

Evolution of microstructure in laser deposited Al-11.28%Si alloy

Abstract: Laser melting of Al–Si alloys has been investigated extensively, however, little work on the microstructural evolution of laser deposited Al–Si alloys has been reported to date. This paper presents a detailed microstructural investigation of laser deposited Al–11.28Si alloy. Laser aided direct metal deposition (DMD) process has been used to build up solid thin wall samples using Al 4047 prealloyed powder. The evolution of macro- and microstructures of laser deposited Al–Si samples was investigated using X-ray diffraction, optical microscopy, scanning electron microscopy and electron backscattered diffraction techniques. Microstructural observation revealed that the morphology and the length scale of the microstructures are different at different locations of the sample. A periodic transition of microstructural morphology from columnar dendrite to microcellular structure was observed in each layer. The observed difference in the microstructure was correlated with the thermal history of the deposit.

Laser additive manufacturing of metallic components: materials, processes and mechanisms

Abstract: Unlike conventional materials removal methods, additive manufacturing (AM) is based on a novel materials incremental manufacturing philosophy. Additive manufacturing implies layer by layer shaping and consolidation of powder feedstock to arbitrary configurations, normally using a computer controlled laser. The current development focus of AM is to produce complex shaped functional metallic components, including metals, alloys and metal matrix composites (MMCs), to meet demanding requirements from aerospace, defence, automotive and biomedical industries. Laser sintering (LS), laser melting (LM) and laser metal deposition (LMD) are presently regarded as the three most versatile AM processes. Laser based AM processes generally have a complex non-equilibrium physical and chemical metallurgical nature, which is material and process dependent. The influence of material characteristics and processing conditions on metallurgical mechanisms and resultant microstructural and mechanical properties of AM proc...