scispace - formally typeset
Search or ask a question
Author

Helena Gleskova

Other affiliations: Princeton University
Bio: Helena Gleskova is an academic researcher from University of Strathclyde. The author has contributed to research in topics: Thin-film transistor & Amorphous silicon. The author has an hindex of 31, co-authored 114 publications receiving 3811 citations. Previous affiliations of Helena Gleskova include Princeton University.


Papers
More filters
Journal ArticleDOI
TL;DR: In this article, the mechanics of film-on-foil transistors on steel and plastic foils have been discussed in the context of thin-film transistors, where the transistors function well after the foils are rolled to small radii of curvature.
Abstract: The mechanics of film-on-foil devices is presented in the context of thin-film transistors on steel and plastic foils Provided the substrates are thin, such transistors function well after the foils are rolled to small radii of curvature When a substrate with a lower elastic modulus is used, smaller radii of curvature can be achieved Furthermore, when the transistors are placed in the neutral surface by sandwiching between a substrate and an encapsulation layer, even smaller radii of curvature can be attained Transistor failure clearly shows when externally forced and thermally induced strains add to, or subtract from, each other

722 citations

Journal ArticleDOI
TL;DR: In this article, the authors applied strain on thin-film transistors (TFTs) made of hydrogenated amorphous silicon on polyimide foil and found that the TFT failed by periodic cracks at a strain of ∼ 0.5%.
Abstract: We have applied strain on thin-film transistors (TFTs) made of hydrogenated amorphous silicon on polyimide foil. In tension, the amorphous layers of the TFT fail by periodic cracks at a strain of ∼0.5%. In compression, the TFTs do not fail when strained by up to 2%, which is the highest value we can set controllably. The amorphous transistor materials can support such large strains because they lack a mechanism for dislocation motion. While the tensile driving force is sufficient to overcome the resistance to crack formation, the compressive failure mechanism of delamination is not activated because of the large delamination length required between transistor layers and polymer substrate.

213 citations

Journal ArticleDOI
TL;DR: In this paper, the authors evaluated amorphous silicon thin-film transistors (TFTs) fabricated on polyimide foil under uniaxial compressive or tensile strain.
Abstract: We evaluated amorphous silicon thin-film transistors (TFTs) fabricated on polyimide foil under uniaxial compressive or tensile strain. The strain was induced by bending or stretching. The on- current and hence the electron linear mobility μ depend on strain e as μ=μ0(1+26×e), where tensile strain has a positive sign and the strain is parallel to the TFT source-drain current path. Upon the application of compressive or tensile strain the mobility changes “instantly” and under compression then remains constant for up to 40 h. In tension, the TFTs fail mechanically at a strain of about +0.003 but recover if the strain is released “immediately.”

168 citations

Journal ArticleDOI
TL;DR: In this paper, the authors summarize the TFT properties and their compatibility with foil substrate materials, and summarize their properties and properties with respect to different modifications of silicon films: amorphous, nanocrystalline and micro-crystalline.

151 citations

Journal ArticleDOI
TL;DR: In this article, the elastic deformation of the transistor is correlated with small increase in the electron mobility and cracks start to form when the tensile strain reaches 0.34, and burst formation starts and causes an abrupt change in the transistor performance.

134 citations


Cited by
More filters
Journal ArticleDOI
25 Jul 2013-Nature
TL;DR: In this paper, the authors present a platform that makes electronics both virtually unbreakable and imperceptible on polyimide polysilicon elastomers, which can be operated at high temperatures and in aqueous environments.
Abstract: Electronic devices have advanced from their heavy, bulky origins to become smart, mobile appliances. Nevertheless, they remain rigid, which precludes their intimate integration into everyday life. Flexible, textile and stretchable electronics are emerging research areas and may yield mainstream technologies. Rollable and unbreakable backplanes with amorphous silicon field-effect transistors on steel substrates only 3 μm thick have been demonstrated. On polymer substrates, bending radii of 0.1 mm have been achieved in flexible electronic devices. Concurrently, the need for compliant electronics that can not only be flexed but also conform to three-dimensional shapes has emerged. Approaches include the transfer of ultrathin polyimide layers encapsulating silicon CMOS circuits onto pre-stretched elastomers, the use of conductive elastomers integrated with organic field-effect transistors (OFETs) on polyimide islands, and fabrication of OFETs and gold interconnects on elastic substrates to realize pressure, temperature and optical sensors. Here we present a platform that makes electronics both virtually unbreakable and imperceptible. Fabricated directly on ultrathin (1 μm) polymer foils, our electronic circuits are light (3 g m(-2)) and ultraflexible and conform to their ambient, dynamic environment. Organic transistors with an ultra-dense oxide gate dielectric a few nanometres thick formed at room temperature enable sophisticated large-area electronic foils with unprecedented mechanical and environmental stability: they withstand repeated bending to radii of 5 μm and less, can be crumpled like paper, accommodate stretching up to 230% on prestrained elastomers, and can be operated at high temperatures and in aqueous environments. Because manufacturing costs of organic electronics are potentially low, imperceptible electronic foils may be as common in the future as plastic wrap is today. Applications include matrix-addressed tactile sensor foils for health care and monitoring, thin-film heaters, temperature and infrared sensors, displays, and organic solar cells.

2,062 citations

Journal ArticleDOI
TL;DR: Integration of organic transistors and rubber pressure sensors, both of which can be produced by low-cost processing technology such as large-area printing technology, will provide an ideal solution to realize a practical artificial skin.
Abstract: It is now widely accepted that skin sensitivity will be very important for future robots used by humans in daily life for housekeeping and entertainment purposes Despite this fact, relatively little progress has been made in the field of pressure recognition compared to the areas of sight and voice recognition, mainly because good artificial “electronic skin” with a large area and mechanical flexibility is not yet available The fabrication of a sensitive skin consisting of thousands of pressure sensors would require a flexible switching matrix that cannot be realized with present silicon-based electronics Organic field-effect transistors can substitute for such conventional electronics because organic circuits are inherently flexible and potentially ultralow in cost even for a large area Thus, integration of organic transistors and rubber pressure sensors, both of which can be produced by low-cost processing technology such as large-area printing technology, will provide an ideal solution to realize a practical artificial skin, whose feasibility has been demonstrated in this paper Pressure images have been taken by flexible active matrix drivers with organic transistors whose mobility reaches as high as 14 cm2/V·s The device is electrically functional even when it is wrapped around a cylindrical bar with a 2-mm radius

1,804 citations

PatentDOI
06 Apr 2012-Science
TL;DR: In this article, the authors present stretchable and printable semiconductors and electronic circuits capable of providing good performance when stretched, compressed, flexed, or otherwise deformed.
Abstract: The present invention provides stretchable, and optionally printable, semiconductors and electronic circuits capable of providing good performance when stretched, compressed, flexed or otherwise deformed. Stretchable semiconductors and electronic circuits of the present invention preferred for some applications are flexible, in addition to being stretchable, and thus are capable of significant elongation, flexing, bending or other deformation along one or more axes. Further, stretchable semiconductors and electronic circuits of the present invention may be adapted to a wide range of device configurations to provide fully flexible electronic and optoelectronic devices.

1,673 citations

Patent
01 Aug 2008
TL;DR: In this article, the oxide semiconductor film has at least a crystallized region in a channel region, which is defined as a region of interest (ROI) for a semiconductor device.
Abstract: An object is to provide a semiconductor device of which a manufacturing process is not complicated and by which cost can be suppressed, by forming a thin film transistor using an oxide semiconductor film typified by zinc oxide, and a manufacturing method thereof. For the semiconductor device, a gate electrode is formed over a substrate; a gate insulating film is formed covering the gate electrode; an oxide semiconductor film is formed over the gate insulating film; and a first conductive film and a second conductive film are formed over the oxide semiconductor film. The oxide semiconductor film has at least a crystallized region in a channel region.

1,501 citations

PatentDOI
TL;DR: In this article, the authors present methods, systems and system components for transferring, assembling and integrating features and arrays of features having selected nanosized and/or microsized physical dimensions, shapes and spatial orientations.
Abstract: The present invention provides methods, systems and system components for transferring, assembling and integrating features and arrays of features having selected nanosized and/or microsized physical dimensions, shapes and spatial orientations. Methods of the present invention utilize principles of ‘soft adhesion’ to guide the transfer, assembly and/or integration of features, such as printable semiconductor elements or other components of electronic devices. Methods of the present invention are useful for transferring features from a donor substrate to the transfer surface of an elastomeric transfer device and, optionally, from the transfer surface of an elastomeric transfer device to the receiving surface of a receiving substrate. The present methods and systems provide highly efficient, registered transfer of features and arrays of features, such as printable semiconductor element, in a concerted manner that maintains the relative spatial orientations of transferred features.

1,305 citations