Hongxia Wang

Bio: Hongxia Wang is an academic researcher from Deakin University. The author has contributed to research in topics: Coating & Electrospinning. The author has an hindex of 41, co-authored 131 publications receiving 6980 citations. Previous affiliations of Hongxia Wang include Geelong Football Club & University of Science and Technology Beijing.

Fluoroalkyl silane modified silicone rubber/nanoparticle composite: a super durable, robust superhydrophobic fabric coating.

Abstract: A superhydrophobic fabric coating made of a crosslinked polydimethylsiloxane elastomer, containing well-dispersed hydrophobic silica nanoparticles and fluorinated alkyl silane, shows remarkable durability against repeated machine washes, severe abrasion, strong acid or base, boiling water or beverages and excellent stain resistance.

Durable, Self-Healing Superhydrophobic and Superoleophobic Surfaces from Fluorinated-Decyl Polyhedral Oligomeric Silsesquioxane and Hydrolyzed Fluorinated Alkyl Silane

Abstract: Super-liquid-repellent surfaces have attracted much attention in both scientific and industrial areas. They are often deemed superhydrophobic or superoleophobic depending on the liquid to be repelled. Superhydrophobic surfaces have a water contact angle greater than 1508. They have interesting nonsticking, self-cleaning, and anti-contamination functions. The emerging applications include separation of oil from water, energy conversion, protection of electronic devices, adjusting cell/substrate adhesion in the biomedical area, and reducing fluid resistance for aquaculture and microfluidic devices. In contrast, superoleophobic surfaces can be rather complicated, but they have great potential applications in antifouling from hazard chemicals and biological contaminants. Although any solid surface can be characterized as superoleophobic as long as its contact angle with an oily fluid is greater than 1508, the surface properties revealed from the contact angle measurement using different contacting oils could be considerably different. For example, a surface that is superoleophobic to certain oily fluids may have lower repellency or even be wettable by other oily fluids of a lower surface tension. It is normally easy to make a surface super-repellent to oils of a high surface tension, but difficult to prepare superoleophobic surfaces against oily fluids that have a surface tension below 35 mNm . Most super-liquid-repellent surfaces have poor durability. Chemical oxidation from exposure to air, a special chemical environment, strong light, or physical rubbing could cause the surfaces to lose their super-repellency permanently. It is imperative to improve the durability for practical applications. Recently, great progress has been made to develop mechanically robust superhydrophobic surfaces and laundering-durable superhydrophobic fabrics. On the other hand, the bioinspired self-healing ability has been proposed to be a promising solution to improve the durability of synthetic superhydrophobic surfaces. Recently, Li et al. reported a self-healing superhydrophobic coating that was prepared by chemical vapor deposition (CVD) of a fluoroalkyl silane on a layer-by-layer assembled porous surface, and self-healing was derived from the reacted fluoroalkyl silane embedded in the rigidly flexible coating layer. Wang et al. also reported the formation of a self-healing superamphiphobic surface on anodized alumina by filling the intrinsic pores with a lowsurface energy liquid. In the recent study, we have also found that fabrics coated with a hydrolysis product from fluorinated-decyl polyhedral oligomeric silsesquioxane (FD–POSS) and a fluorinated alkyl silane (FAS) have a self-healing superhydrophobic and superoleophobic surface and the coating shows excellent durability to acid, UV light, machine wash, and abrasion. Herein, we first report on its novel multiple self-healing ability and durable performance. The chemical structures of FD-POSS and FAS are shown in Figure 1 a. The coating solution was prepared by dissolving FD-POSS in five times its weight of FAS, and the resulting viscous solution was then dispersed in ethanol. After ultrasonication for 30 min, a homogeneous dispersion was obtained. Figure 1b shows the appearance of an FD–POSS/ FAS dispersion in ethanol. Such a suspension was stable at

Robust, self-healing superamphiphobic fabrics prepared by two-step coating of fluoro-containing polymer, fluoroalkyl silane, and modified silica nanoparticles

Abstract: A robust, superamphiphobic fabric with a novel self-healing ability to autorepair from chemical damage is prepared by a two-step wet-chemistry coating technique using an easily available material system consisting of poly(vinylidene fluoride-co-hexafluoropropylene), fluoroalkyl silane, and modified silica nanoparticles. The coated fabrics can withstand at least 600 cycles of standard laundry and 8000 cycles of abrasion without apparently changing the superamphiphobicity. The coating is also very stable to strong acid/base, ozone, and boiling treatments. After being damaged chemically, the coating can restore its super liquid-repellent properties by a short-time heating treatment or room temperature ageing. This simple but novel and effective coating system may be useful for the development of robust protective clothing for various applications.

The charge effect of cationic surfactants on the elimination of fibre beads in the electrospinning of polystyrene

Abstract: Polystyrene nanofibres were electrospun with the inclusion of cationic surfactants, dodecyltrimethylammonium bromide (DTAB) or tetrabutylammonium chloride (TBAC), in the polymer solution. A small amount of cationic surfactant effectively stopped the formation of beaded fibres during the electrospinning. The cationic surfactants were also found to improve the solution conductivity, but had no effect on the viscosity. Only DTAB had an effect on the surface tension of the polymer solution, the surface tension decreasing slightly with an increase in the concentration of DTAB. The formation of beaded fibres was attributed to an insufficient stretch of the filaments during the whipping of the jet, due to a low charge density. Adding the cationic surfactants improved the net charge density that enhanced the whipping instability. The jet was stretched under stronger charge repulsion and at a higher speed, resulting in an exhaustion of the bead structure. In addition, a polymer/surfactant interaction was found in the polystyrene–DTAB solution system, while this interaction was not found in the polystyrene–TBAC system. The polymer/surfactant interaction led to the formation of thinner fibres than those formed in the absence of the interaction. The effects of a non-ionic surfactant, Triton X-405, on the electrospun fibres were also studied. The addition of Triton X-405 did not eliminate the fibre beads, but reduced the bead numbers and changed the morphology. Triton X-405 slightly improved the solution conductivity, and had a minor effect on the surface tension, but no effect on the viscosity.

Electrospinning: A Fascinating Method for the Preparation of Ultrathin Fibers

Abstract: Electrospinning is a highly versatile method to process solutions or melts, mainly of polymers, into continuous fibers with diameters ranging from a few micrometers to a few nanometers. This technique is applicable to virtually every soluble or fusible polymer. The polymers can be chemically modified and can also be tailored with additives ranging from simple carbon-black particles to complex species such as enzymes, viruses, and bacteria. Electrospinning appears to be straightforward, but is a rather intricate process that depends on a multitude of molecular, process, and technical parameters. The method provides access to entirely new materials, which may have complex chemical structures. Electrospinning is not only a focus of intense academic investigation; the technique is already being applied in many technological areas.

Ultracapacitors: Why, How, and Where is the Technology

Abstract: The science and technology of ultracapacitors are reviewed for a number of electrode materials, including carbon, mixed metal oxides, and conducting polymers. More work has been done using microporous carbons than with the other materials and most of the commercially available devices use carbon electrodes and an organic electrolytes. The energy density of these devices is 3¯5 Wh/kg with a power density of 300¯500 W/kg for high efficiency (90¯95%) charge/discharges. Projections of future developments using carbon indicate that energy densities of 10 Wh/kg or higher are likely with power densities of 1¯2 kW/kg. A key problem in the fabrication of these advanced devices is the bonding of the thin electrodes to a current collector such the contact resistance is less than 0.1 cm2. Special attention is given in the paper to comparing the power density characteristics of ultracapacitors and batteries. The comparisons should be made at the same charge/discharge efficiency.

Electrospinning and Electrospun Nanofibers: Methods, Materials, and Applications

Abstract: Electrospinning is a versatile and viable technique for generating ultrathin fibers. Remarkable progress has been made with regard to the development of electrospinning methods and engineering of electrospun nanofibers to suit or enable various applications. We aim to provide a comprehensive overview of electrospinning, including the principle, methods, materials, and applications. We begin with a brief introduction to the early history of electrospinning, followed by discussion of its principle and typical apparatus. We then discuss its renaissance over the past two decades as a powerful technology for the production of nanofibers with diversified compositions, structures, and properties. Afterward, we discuss the applications of electrospun nanofibers, including their use as "smart" mats, filtration membranes, catalytic supports, energy harvesting/conversion/storage components, and photonic and electronic devices, as well as biomedical scaffolds. We highlight the most relevant and recent advances related to the applications of electrospun nanofibers by focusing on the most representative examples. We also offer perspectives on the challenges, opportunities, and new directions for future development. At the end, we discuss approaches to the scale-up production of electrospun nanofibers and briefly discuss various types of commercial products based on electrospun nanofibers that have found widespread use in our everyday life.

Electrospinning of polymeric nanofibers for tissue engineering applications: a review.

Abstract: Interest in electrospinning has recently escalated due to the ability to produce materials with nanoscale properties. Electrospun fibers have been investigated as promising tissue engineering scaffolds since they mimic the nanoscale properties of native extracellular matrix. In this review, we examine electrospinning by providing a brief description of the theory behind the process, examining the effect of changing the process parameters on fiber morphology, and discussing the potential applications and impacts of electrospinning on the field of tissue engineering.

A review on electrospinning design and nanofibre assemblies.

Abstract: Although there are many methods of fabricating nanofibres, electrospinning is perhaps the most versatile process. Materials such as polymer, composites, ceramic and metal nanofibres have been fabricated using electrospinning directly or through post-spinning processes. However, what makes electrospinning different from other nanofibre fabrication processes is its ability to form various fibre assemblies. This will certainly enhance the performance of products made from nanofibres and allow application specific modifications. It is therefore vital for us to understand the various parameters and processes that allow us to fabricate the desired fibre assemblies. Fibre assemblies that can be fabricated include nonwoven fibre mesh, aligned fibre mesh, patterned fibre mesh, random three-dimensional structures and sub-micron spring and convoluted fibres. Nevertheless, more studies are required to understand and precisely control the actual mechanics in the formation of various electrospun fibrous assemblies.