Hua Hu and

Bio: Hua Hu and is an academic researcher from University of Michigan. The author has contributed to research in topics: Water vapor & Thermal diffusivity. The author has an hindex of 1, co-authored 1 publications receiving 1136 citations.

Evaporation of a Sessile Droplet on a Substrate

Abstract: The evaporation of a sessile droplet with a pinned contact line is investigated experimentally, by analytic theory and by computation using the finite element method (FEM). Because of the low value of R2/Dtf = cv(1 − H)/ρ = 1.4 × 10-5, where R is the contact-line radius, D is the water vapor diffusivity, cv is the saturated water vapor concentration, H is the relative humidity, and ρ is the liquid water density, the evaporation can be considered as a quasi-steady-state process. Hence, the vapor concentration distribution above the droplet satisfies the Laplace equation but with a time-varying droplet surface. It is found both theoretically and experimentally that the net evaporation rate from the droplet remains almost constant with time for a small initial contact angle (θ < 40°), even though the evaporation flux becomes more strongly singular at the edge of the droplet as the contact angle decreases during evaporation. We also measured the critical contact angle at which the contact line starts to reced...

Marangoni effect reverses coffee-ring depositions.

Abstract: We show here both experimentally and theoretically that the formation of “coffee-ring” deposits observed at the edge of drying water droplets requires not only a pinned contact line (Deegan et al. Nature 1997, 389, 827) but also suppression of Marangoni flow. For simple organic fluids, deposition actually occurs preferentially at the center of the droplet, due to a recirculatory flow driven by surface-tension gradients produced by the latent heat of evaporation. The manipulation of this Marangoni flow in a drying droplet should allow one in principle to control and redirect evaporation-driven deposition and assembly of colloids and other materials.

Suppression of the coffee-ring effect by shape-dependent capillary interactions

Abstract: When a drop of liquid dries on a solid surface, its suspended particulate matter is deposited in ring-like fashion. This phenomenon, known as the coffee-ring effect, is familiar to anyone who has observed a drop of coffee dry. During the drying process, drop edges become pinned to the substrate, and capillary flow outward from the centre of the drop brings suspended particles to the edge as evaporation proceeds. After evaporation, suspended particles are left highly concentrated along the original drop edge. The coffee-ring effect is manifested in systems with diverse constituents, ranging from large colloids to nanoparticles and individual molecules. In fact--despite the many practical applications for uniform coatings in printing, biology and complex assembly-the ubiquitous nature of the effect has made it difficult to avoid. Here we show experimentally that the shape of the suspended particles is important and can be used to eliminate the coffee-ring effect: ellipsoidal particles are deposited uniformly during evaporation. The anisotropic shape of the particles significantly deforms interfaces, producing strong interparticle capillary interactions. Thus, after the ellipsoids are carried to the air-water interface by the same outward flow that causes the coffee-ring effect for spheres, strong long-ranged interparticle attractions between ellipsoids lead to the formation of loosely packed or arrested structures on the air-water interface. These structures prevent the suspended particles from reaching the drop edge and ensure uniform deposition. Interestingly, under appropriate conditions, suspensions of spheres mixed with a small number of ellipsoids also produce uniform deposition. Thus, particle shape provides a convenient parameter to control the deposition of particles, without modification of particle or solvent chemistry.

Control of colloidal particle deposit patterns within picoliter droplets ejected by ink-jet printing.

Abstract: Particle deposit morphologies that resulted from evaporating ink-jetted microdroplets were controlled by varying the ink compositions and concentrations. The ink was a well-dispersed aqueous dispersion of monodisperse silica microspheres. Silica particles suspended in the microdroplet undergo self-assembly upon the evaporation of the solvent. A ringlike deposit of the self-assembled silica particles was produced from the water-based ink, while a uniform two-dimensional monolayer with a well-ordered hexagonal structure was obtained from the mixed-solvent-based inks. Variations in the deposit patterns can be explained in terms of competing effects between the convective and Marangoni flows, which vary with the types of the high-boiling-point solvent added to the ink. The macroscopic shape and microstructure of the silica colloidal deposits were observed by SEM, AFM, and a confocal microscope.

Evaporative deposition patterns: spatial dimensions of the deposit.

Abstract: A model accounting for the finite spatial dimensions of the deposit patterns in evaporating sessile drops of a colloidal solution on a plane substrate is proposed. The model is based on the assumption that the solute particles occupy finite volume and hence these dimensions are of steric origin. Within this model, the geometrical characteristics of the deposition patterns are found as functions of the initial concentration of the solute, the initial geometry of the drop, and the time elapsed from the beginning of the drying process. The model is solved analytically for small initial concentrations of the solute and numerically for arbitrary initial concentrations of the solute. The agreement between our theoretical results and the experimental data is demonstrated, and it is shown that the observed dependence of the deposit dimensions on the experimental parameters can indeed be attributed to the finite dimensions of the solute particles. These results are universal and do not depend on any free or fitting parameters; they are important for understanding evaporative deposition and may be useful for creating controlled deposition patterns.

Surface nanobubbles and nanodroplets

Abstract: Surface nanobubbles are nanoscopic gaseous domains on immersed substrates which can survive for days. They were first speculated to exist about 20 years ago, based on stepwise features in force curves between two hydrophobic surfaces, eventually leading to the first atomic force microscopy (AFM) image in 2000. While in the early years it was suspected that they may be an artifact caused by AFM, meanwhile their existence has been confirmed with various other methods, including through direct optical observation. Their existence seems to be paradoxical, as a simple classical estimate suggests that they should dissolve in microseconds, due to the large Laplace pressure inside these nanoscopic spherical-cap-shaped objects. Moreover, their contact angle (on the gas side) is much smaller than one would expect from macroscopic counterparts. This review will not only give an overview on surface nanobubbles, but also on surface nanodroplets, which are nanoscopic droplets (e.g., of oil) on (hydrophobic) substrates immersed in water, as they show similar properties and can easily be confused with surface nanobubbles and as they are produced in a similar way, namely, by a solvent exchange process, leading to local oversaturation of the water with gas or oil, respectively, and thus to nucleation. The review starts with how surface nanobubbles and nanodroplets can be made, how they can be observed (both individually and collectively), and what their properties are. Molecular dynamic simulations and theories to account for the long lifetime of the surface nanobubbles are then reported on. The crucial element contributing to the long lifetime of surface nanobubbles and nanodroplets is pinning of the three-phase contact line at chemical or geometric surface heterogeneities. The dynamical evolution of the surface nanobubbles then follows from the diffusion equation, Laplace’s equation, and Henry’s law. In particular, one obtains stable surface nanobubbles when the gas influx from the gas-oversaturated water and the outflux due to Laplace pressure balance. This is only possible for small enough surface bubbles. It is therefore the gas or oil oversaturation ζ that determines the contact angle of the surface nanobubble or nanodroplet and not the Young equation. The review also covers the potential technological relevance of surface nanobubbles and nanodroplets, namely, in flotation, in (photo)catalysis and electrolysis, in nanomaterial engineering, for transport in and out of nanofluidic devices, and for plasmonic bubbles, vapor nanobubbles, and energy conversion. Also given is a discussion on surface nanobubbles and nanodroplets in a nutshell, including theoretical predictions resulting from it and future directions. Studying the nucleation, growth, and dissolution dynamics of surface nanobubbles and nanodroplets will shed new light on the problems of contact line pinning and contact angle hysteresis on the submicron scale.