Huai Wang

Bio: Huai Wang is an academic researcher from Aalborg University. The author has contributed to research in topics: Capacitor & Power electronics. The author has an hindex of 38, co-authored 328 publications receiving 7480 citations. Previous affiliations of Huai Wang include Yangtze University & City University of Hong Kong.

A Hybrid Power Control Concept for PV Inverters with Reduced

Abstract: This letter proposes a hybrid power control con- cept for grid-connected Photovoltaic (PV) inverters. The control strategy is based on either a Maximum Power Point Tracking (MPPT) control or a Constant Power Generation (CPG) control depending on the instantaneous available power from the PV panels. The essence of the proposed concept lies in the selection of an appropriate power limit for the CPG control to achieve an improved thermal performance and an increased utilization factor of PV inverters, and thus to cater for a higher penetration level of PV systems with intermittent nature. A case study on a single-phase PV inverter under yearly operation is presented with analyses of the thermal loading, lifetime, and annual energy yield. It has revealed the trade-off factors to select the power limit and also verified the feasibility and the effectiveness of the proposed control concept. may severely exceed the initial project outlay. The energy storage elements are mostly installed at the substation side instead of in the individual inverters also considering cost and maintenance. Since the above solutions introduce considerable investments, two kinds of hybrid control concepts have been proposed in prior-art research. In (3), an MPPT control with a reduced power mode control has been introduced to avoid dynamic overloading in a stand-alone wind-PV generation system. The selection of the power limit for the reduced power mode control is dynamically in accordance to the power oscillations during wind turbine soft stalling. The reduced power mode operation is achieved by modifying the MPPT algorithm based on a virtual MPPT. In (8) , an MPPT control with power curtailment control is proposed to prevent over- voltage of low voltage feeders by limiting the excessive power injection to the grid from PV inverters. The selection of the power limit for the power curtailment control depends on the upper voltage limit of the low voltage feeders. These control concepts can effectively avoid the over-loading issue with an acceptable reduction of the overall energy generation (9). However, the issue on the utilization of PV inverter remains and the thermal performance of the PV inverters is still unknown.

On the Stability of Power Electronics-Dominated Systems: Challenges and Potential Solutions

Abstract: The modern power system is becoming more complicated due to the ever increasing penetration of power electronics, which is referred to as a power-electronics-dominated system (PEDS). In this case, the analysis, control, and operation of the entire power system should tone with the energy-paradigm transition pace, where the challenges should be properly tackled. After the brief introduction of grid-connected converters, this article explores stability challenges of PEDSs, especially on the low inertia issue and multitimescale characteristics, as well as the dynamics when connected to weak grids. The low inertia issue is considered as one of great challenges that power electronics introduce to the conventional power grid. Accordingly, the stability issues of PEDSs are discussed. The exploration reveals that the multitimescale coupling among various control loops and the mutual effects of multiple converters demand much more attention than ever before. The coordinated control of converters for the global stability of PEDSs is also summarized, part of which offers the possibility to solve the inertia problem. This article serves as an inspiration on potential solutions to these issues. In order to provide a more intuitive impression of the inertia problem in PEDSs, a case study is exemplified to highlight the analysis and discussion.

An Overview of Condition Monitoring Techniques for Capacitors in DC-Link Applications

Abstract: Capacitors are widely used in dc links of power electronic converters to balance power, suppress voltage ripple, and store short-term energy. Condition monitoring (CM) of dc-link capacitors has great significance in enhancing the reliability of power converter systems. Over the past few years, many efforts have been made to realize CM of dc-link capacitors. This article gives an overview and a comprehensive comparative evaluation of them with emphasis on the application objectives, implementation methods, and monitoring accuracy when being used. First, the design procedure for the CM of capacitors is introduced. Second, the main capacitor parameters estimation principles are summarized. According to these principles, various possible CM methods are derived in a step-by-step manner. On this basis, a comprehensive review and comparison of CM schemes for different types of dc-link applications are provided. Finally, application recommendations and future research trends are presented.

A Digital Twin Based Estimation Method for Health Indicators of DC–DC Converters

Abstract: This article proposes a health indicator estimation method based on the digital-twin concept aiming for condition monitoring of power electronic converters. The method is noninvasive, without additional hardware circuits, and calibration requirements. An application for a buck dc–dc converter is demonstrated with theoretical analyses, practical considerations, and experimental verifications. The digital replica of an experimental prototype is established, which includes the power stage, sampling circuit, and close-loop controller. Particle swarm optimization algorithm is applied to estimate the unknown circuit parameters of interest based on the incoming data from both the digital twin and the physical prototype. Cluster-data of the estimated health indicators under different testing conditions of the buck converter is analyzed and used for observing the degradation trends of key components, such as capacitor and MOSFET. The outcomes of this article serve as a key step for achieving noninvasive, cost-effective, and robust condition monitoring for power electronic converters.

A Temperature-Dependent Thermal Model of IGBT Modules Suitable for Circuit-Level Simulations

Abstract: A basic challenge in the insulated gate bipolar transistor (IGBT) transient simulation study is to obtain the realistic junction temperature, which demands not only accurate electrical simulations but also precise thermal impedance. This paper proposed a transient thermal model for IGBT junction temperature simulations during short circuits or overloads. The updated Cauer thermal model with varying thermal parameters is obtained by means of finite-element method (FEM) thermal simulations with temperature-dependent physical parameters. The proposed method is applied to a case study of a 1700 V/1000 A IGBT module. Furthermore, a testing setup is built up to validate the simulation results, which is composed of a IGBT baseplate temperature control unit, an infrared camera with a maximum of 3 kHz sampling frequency, and a black-painted open IGBT module.

I and i

Abstract: There is, I think, something ethereal about i —the square root of minus one. I remember first hearing about it at school. It seemed an odd beast at that time—an intruder hovering on the edge of reality. Usually familiarity dulls this sense of the bizarre, but in the case of i it was the reverse: over the years the sense of its surreal nature intensified. It seemed that it was impossible to write mathematics that described the real world in …

Ultracapacitors: Why, How, and Where is the Technology

Abstract: The science and technology of ultracapacitors are reviewed for a number of electrode materials, including carbon, mixed metal oxides, and conducting polymers. More work has been done using microporous carbons than with the other materials and most of the commercially available devices use carbon electrodes and an organic electrolytes. The energy density of these devices is 3¯5 Wh/kg with a power density of 300¯500 W/kg for high efficiency (90¯95%) charge/discharges. Projections of future developments using carbon indicate that energy densities of 10 Wh/kg or higher are likely with power densities of 1¯2 kW/kg. A key problem in the fabrication of these advanced devices is the bonding of the thin electrodes to a current collector such the contact resistance is less than 0.1 cm2. Special attention is given in the paper to comparing the power density characteristics of ultracapacitors and batteries. The comparisons should be made at the same charge/discharge efficiency.

Light-emitting diodes

Abstract: Light-Emitting Diodes. (Monographs in Electrical and Electronic Engineering.) By A. A. Bergh and P. J. Dean. Pp. viii+591. (Clarendon: Oxford; Oxford University: London, 1976.) £22.