Huai Wang

Bio: Huai Wang is an academic researcher from Aalborg University. The author has contributed to research in topics: Capacitor & Power electronics. The author has an hindex of 38, co-authored 328 publications receiving 7480 citations. Previous affiliations of Huai Wang include Yangtze University & City University of Hong Kong.

Suggested grid code modifications to ensure wide-scale adoption of photovoltaic energy in distributed power generation systems

Abstract: Current grid standards seem to largely require low power (e.g. several kilowatts) single-phase photovoltaic (PV) systems to operate at unity power factor with maximum power point tracking, and disconnect from the grid under grid faults. However, in case of wide-scale penetration of single-phase PV systems in the distributed grid, the disconnection under grid faults can contribute to: a) voltage flickers, b) power outages, and c) system instability. In this paper, grid code modifications are explored for wide-scale adoption of PV systems in the distribution grid. More recently, Italy and Japan, have undertaken a major review of standards for PV power conversion systems connected to low voltage networks. In view of this, the importance of low voltage ride-through for single-phase PV power systems under grid faults along with reactive power injection is studied in this paper. Three reactive power injection strategies are discussed in detail. Simulations are presented for a PV power system with low voltage ride-through capability and ancillary services. An example of a full-bridge single-phase grid-connected system is tested experimentally to demonstrate the potential benefits.

Benchmarking of Constant Power Generation Strategies for Single-Phase Grid-Connected Photovoltaic Systems

Abstract: With a still increase of grid-connected photovoltaic (PV) systems, challenges have been imposed on the grid due to the continuous injection of a large amount of fluctuating PV power, like overloading the grid infrastructure (e.g., transformers) during peak power production periods. Hence, advanced active power control methods are required. As a cost-effective solution to avoid overloading, a constant power generation (CPG) control scheme by limiting the feed-in power has been introduced into the currently active grid regulations. In order to achieve a CPG operation, this paper presents three CPG strategies based on a power control method (P-CPG), a current limit method (I-CPG), and the perturb and observe algorithm (P&O-CPG). However, the operational mode changes (e.g., from the maximum power point tracking to a CPG operation) will affect the entire system performance. Thus, a benchmarking of the presented CPG strategies is also conducted on a 3-kW single-phase grid-connected PV system. Comparisons reveal that either the P-CPG or I-CPG strategies can achieve fast dynamics and satisfactory steady-state performance. In contrast, the P&O-CPG algorithm is the most suitable solution in terms of high robustness, but it presents poor dynamic performance.

Wear-Out Failure Analysis of an Impedance-Source PV Microinverter Based on System-Level Electrothermal Modeling

Abstract: In this paper, the wear-out performance of an impedance-source photovoltaic (PV) microinverter (MI) is evaluated and improved based on two different mission profiles. The operating principle and hardware implementation of the MI are first described. With the experimental measurements on a 300-W MI prototype and system-level finite-element method simulations, the electrothermal models are built for the most reliability-critical components, i.e., power semiconductor devices and capacitors. The dependence of the power loss on the junction/hotspot temperature is considered, the enclosure temperature is taken into account, and the thermal cross-coupling effect between components is modeled. Then, the long-term junction/hotspot temperature profiles are derived and further translated into components’ annual damages with the lifetime and damage accumulation models. After that, the Monte Carlo simulation and Weibull analysis are conducted to obtain the system wear-out failure probability over time. It reveals that both the mission profile and the thermal cross-coupling effect have a significant impact on the prediction of system wear-out failure, and the dc-link electrolytic capacitor is the bottleneck of long-term reliability. Finally, the multimode control with a variable dc-link voltage is proposed, and a more reliable dc-link electrolytic capacitor is employed, which results in a remarkable reliability improvement for the studied PV MI.

A Two-Terminal Active Capacitor

Abstract: This letter proposes a concept of two-terminal active capacitor implemented by power semiconductor switches and passive elements. The active capacitor has the same level of convenience as a passive one with two power terminals only. It is application independent and can be specified by rated voltage, ripple current, equivalent series resistance, and operational frequency range. The concept, control method, self-power scheme, and impedance characteristics of the active capacitor are presented. A case study of the proposed active capacitor for a capacitive dc-link application is discussed. The results reveal a significantly lower overall energy storage of passive elements and a reduced cost to fulfill a specific reliability target, compared to a passive capacitor solution. Proof-of-concept experimental results are given to verify the functionality of the proposed capacitor.

I and i

Abstract: There is, I think, something ethereal about i —the square root of minus one. I remember first hearing about it at school. It seemed an odd beast at that time—an intruder hovering on the edge of reality. Usually familiarity dulls this sense of the bizarre, but in the case of i it was the reverse: over the years the sense of its surreal nature intensified. It seemed that it was impossible to write mathematics that described the real world in …

Ultracapacitors: Why, How, and Where is the Technology

Abstract: The science and technology of ultracapacitors are reviewed for a number of electrode materials, including carbon, mixed metal oxides, and conducting polymers. More work has been done using microporous carbons than with the other materials and most of the commercially available devices use carbon electrodes and an organic electrolytes. The energy density of these devices is 3¯5 Wh/kg with a power density of 300¯500 W/kg for high efficiency (90¯95%) charge/discharges. Projections of future developments using carbon indicate that energy densities of 10 Wh/kg or higher are likely with power densities of 1¯2 kW/kg. A key problem in the fabrication of these advanced devices is the bonding of the thin electrodes to a current collector such the contact resistance is less than 0.1 cm2. Special attention is given in the paper to comparing the power density characteristics of ultracapacitors and batteries. The comparisons should be made at the same charge/discharge efficiency.

Light-emitting diodes

Abstract: Light-Emitting Diodes. (Monographs in Electrical and Electronic Engineering.) By A. A. Bergh and P. J. Dean. Pp. viii+591. (Clarendon: Oxford; Oxford University: London, 1976.) £22.