Hukam Mongia

Bio: Hukam Mongia is an academic researcher from Purdue University. The author has contributed to research in topics: Combustor & Combustion chamber. The author has an hindex of 33, co-authored 210 publications receiving 4455 citations. Previous affiliations of Hukam Mongia include GE Aviation & General Electric.

Large-Eddy Simulation of a Gas Turbine Combustor Flow

Abstract: Large-eddy simulation (LES) of turbulent premixed reacting flows in a gas turbine combustor (General Electric's lean premixed dry low-NOx LM6000) has been carried out to evaluate the potential of LES for design studies of realistic hardware. A flamelet model for the premixed flame is combined with a dynamic model for the subgrid kinetic energy to simulate the propagation of the turbulent flame in this high swirl and high Reynolds number flow. Comparison of the computed results with experimental data indicate good agreement in spite of relatively coarse grid resolution employed in the LES. These results provide significant confidence that LES capability for design studies of practical interest is feasible in the near future.

Semianalytical Correlations for NOx, CO, and UHC Emissions

Abstract: To meet the future goals of reduced emissions produced by gas turbine combustors, a better understanding of the process of formation of various pollutants is required. Both empirical and analytical approaches are used to provide the exhaust concentrations of pollutants of interest such as NOx , CO, and unburned hydrocarbon with varying degrees of success. In the present investigation, an emission model that simulates the combustor by a number of reactors representing various combustion zones is proposed. A detailed chemical kinetic scheme was used to provide a fundamental basis for the derivation of a number of expressions that simulate the reaction scheme. The model addresses the combined effects of spray evaporation and mixing in the reaction zone. The model validation included the utilization of a large data base obtained for an annular combustor of a modern turbopropulsion engine. In addition to the satisfactory agreement with the measurements, the model provided insight into the regions within the combustor that could be responsible for the excessive formation of emissions. Methods to reduce the emissions may be implemented in light of such information.

Challenges and Progress in Controlling Dynamics in Gas Turbine Combustors

Abstract: Combustion dynamics impact the design of both conventional diffusion e ame gas turbine combustors and lean premixed combustion systems. The occurrence of dynamics in diffusion e ame combustors can generally be eliminated through changes to the fueling system or operating characteristics driven primarily through empirical design know-how. Lean premixed combustors, such as industrial aeroderivative dry low-emissions combustors, have more persistent dynamics problems that are only partially ameliorated with application of empirical tools and controls. With continuing emphasis on reducing emissions and cost and increasing performance of turbopropulsion engine combustors, the design direction of e ight engines is approaching the lean premixed limit; thus, there is a need for improved tools and control strategies for combustion dynamics in these applications as well. The components of a combined analytical, experimental, and computational approach to understanding and controlling combustion dynamics are being developed. With successful implementation of such an analytical and control mechanism, further improvements in the emissions, stability, and durability characteristics of both e ight and industrial combustors will become possible.

Combustor mixer having plasma generating nozzle

Abstract: A mixer assembly for use in a combustion chamber of a gas turbine engine. The mixer assembly includes a mixer housing having a hollow interior, an inlet and an outlet. The housing delivers a mixture of fuel and air through the outlet to the combustion chamber for burning. The mixer assembly includes a fuel nozzle assembly mounted in the housing having a fuel passage adapted for connection to a fuel supply. The passage extends to an outlet port for delivering fuel from the passage to the hollow interior of the mixer housing. The nozzle assembly includes a plasma generator for generating at least one of a dissociated fuel and an ionized fuel from the fuel delivered through the nozzle outlet port to the hollow interior of the housing.

Large-eddy simulations of gas-turbine swirl injector flow dynamics

Abstract: A comprehensive study on confined swirling flows in an operational gas-turbine injector was performed by means of large-eddy simulations. The formulation was based on the Favre-filtered conservation equations and a modified Smagorinsky treatment of subgrid-scale motions. The model was then numerically solved by means of a preconditioned density-based finite-volume approach. Calculated mean velocities and turbulence properties show good agreement with experimental data obtained from the laser-Doppler velocimetry measurements. Various aspects of the swirling flow development (such as the central recirculating flow, precessing vortex core and Kelvin–Helmholtz instability) were explored in detail. Both co- and counter-rotating configurations were considered, and the effects of swirl direction on flow characteristics were examined. The flow evolution inside the injector is dictated mainly by the air delivered through the primary swirler. The impact of the secondary swirler appears to be limited.

Computational Fluid Dynamics: Principles and Applications Ed. 3

Abstract: Computational Fluid Dynamics: Principles and Applications, Third Edition presents students, engineers, and scientists with all they need to gain a solid understanding of the numerical methods and principles underlying modern computation techniques in fluid dynamics By providing complete coverage of the essential knowledge required in order to write codes or understand commercial codes, the book gives the reader an overview of fundamentals and solution strategies in the early chapters before moving on to cover the details of different solution techniques This updated edition includes new worked programming examples, expanded coverage and recent literature regarding incompressible flows, the Discontinuous Galerkin Method, the Lattice Boltzmann Method, higher-order spatial schemes, implicit Runge-Kutta methods and parallelization An accompanying companion website contains the sources of 1-D and 2-D Euler and Navier-Stokes flow solvers (structured and unstructured) and grid generators, along with tools for Von Neumann stability analysis of 1-D model equations and examples of various parallelization techniques Will provide you with the knowledge required to develop and understand modern flow simulation codes Features new worked programming examples and expanded coverage of incompressible flows, implicit Runge-Kutta methods and code parallelization, among other topics Includes accompanying companion website that contains the sources of 1-D and 2-D flow solvers as well as grid generators and examples of parallelization techniques

Large-eddy simulation of turbulent combustion

Abstract: Large-eddy simulation (LES) of turbulent combustion is a relatively new research field. Much research has been carried out over the past years, but to realize the full predictive potential of combustion LES, many fundamental questions still have to be addressed, and common practices of LES of nonreacting flows revisited. The focus of the present review is to highlight the fundamental differences between Reynolds-averaged Navier-Stokes (RANS) and LES combustion models for nonpremixed and premixed turbulent combustion, to identify some of the open questions and modeling issues for LES, and to provide future perspectives.

New insights into large eddy simulation

Abstract: Fluid dynamic turbulence is one of the most challenging computational physics problems because of the extremely wide range of time and space scales involved, the strong nonlinearity of the governing equations, and the many practical and important applications. While most linear fluid instabilities are well understood, the nonlinear interactions among them makes even the relatively simple limit of homogeneous isotropic turbulence difficult to treat physically, mathematically, and computationally. Turbulence is modeled computationally by a two-stage bootstrap process. The first stage, direct numerical simulation, attempts to resolve the relevant physical time and space scales but its application is limited to diffusive flows with a relatively small Reynolds number (Re). Using direct numerical simulation to provide a database, in turn, allows calibration of phenomenological turbulence models for engineering applications. Large eddy simulation incorporates a form of turbulence modeling applicable when the large-scale flows of interest are intrinsically time dependent, thus throwing common statistical models into question. A promising approach to large eddy simulation involves the use of high-resolution monotone computational fluid dynamics algorithms such as flux-corrected transport or the piecewise parabolic method which have intrinsic subgrid turbulence models coupled naturally to the resolved scales in the computed flow. The physical considerations underlying and evidence supporting this monotone integrated large eddy simulation approach are discussed.