The AlAdhaim Dam is located 133 kilometers northeast of Baghdad. It is a multipurpose dam and joints the Iraqi dam system in 2000. It has a storage capacity of 1.5 billion m3. The dam has an ogee spillway with a length of 562 m, a crest level of 131.5 m.a.m.s.l. and a maximum discharge capacity of 1150 m3/s at its maximum storage height of 143 m.a.m.s.l. This research aimed to investigate the hydrodynamics performance of the spillway and the stilling basin of AlAdhiam Dam by using numerical simulation models under gated situations. It was suggested to modify the dam capacity by increasing the dam's storage capacity by installing gates on the crest of the dam spillway. The FLUENT program was used to simulate the flow over the spillway. The free surface was calculated using the volume of fluid (VOF) method. To deal with turbulence, the SST k-ω turbulence model was used. The study showed that the spillway is capable of carrying the designed flood discharge and the modified conditions with negative pressure behind the gate and at some points along the spillway. Hydraulic jumps occur at various distances throughout the plunge pool depending on the incoming velocity in the flip bucket.

/pdf/flow-over-the-spillway-of-aladhiam-dam-under-gated-condition-efksvk8y.pdf

Flow Over the Spillway of AlAdhiam Dam Under Gated Condition

This study examines the vibrations produced by hydropower operations to improve embankment dam safety. This study consists of two parts: In the first part, ANSYS-CFX was used to generate a three-dimensional (3-D) finite volume (FV) model to simulate a vertical Francis turbine unit in the Mosul hydropower plant. The pressure pattern result of the turbine model was transformed into the dam body to show how the turbine unit's operation affects the dam's stability. The upstream reservoir conditions, various flow rates, and fully open inlet gates were considered. In the second part of this study, a 3-D FE Mosul dam model was simulated using an ANSYS program. The operational turbine model's water pressure pattern is conveyed to the dam's turbine-shared zone. The maximal and minimal upstream reservoir water levels were investigated. A control program was created depending on the principle stress model results collected from the operation of the hydropower plant with the minimum principal stress on the dam body. This research suggests an enhanced turbine operating system, reducing stress on the dam body and increasing dam operation life.
 

/pdf/a-control-program-for-hydropower-operation-based-on-v8ogcv6r.pdf

A Control Program for Hydropower Operation Based on Minimizing the Principal Stress Values on the Dam Body: Mosul Dam Case Study

The hydraulic behavior of the flow can be changed by using large-scale geometric roughness elements in open channels. This change can help in controlling erosions and sedimentations along the mainstream of the channel. Roughness elements can be large stone or concrete blocks placed at the channel's bed to impose more resistance in the bed. The geometry of the roughness elements, numbers used, and configuration are parameters that can affect the flow's hydraulic characteristics. In this paper, velocity distribution along the flume was theoretically investigated using a series of tests of T-shape roughness elements, fixed height, arranged in three different configurations, differ in the number of lines of roughness element. These elements were used to find the best configuration of roughness elements that can be applied to change the flow's hydraulic characteristics. ANSYS Parametric Design Language, APDL, and Computational Fluid Dynamics, CFD, was used to simulate the flow in an open channel with roughness elements. CFD can be used to study the hydrodynamics of open channels under different conditions with inclusive details rather than relying on the costly field and time-consuming. Runs were implemented with different conditions, the discharge, and water depth in upstream and downstream of the flume. T-shape roughness elements with height equal to 3cm placed in three different configurations, two lines, four lines, and fully rough configurations were tested. The results show that the effect of roughness elements increasing with increasing the number of lines of roughness elements. Cases of four lines and fully rough configurations have almost the same hydraulic performance by having the same results of the velocity decrease percentage, which is decreased by approximately about 66% and 61% of the control case's velocity in the zone near the roughness elements consequently. But the difference is that four lines configuration is affected in a part of the test section. This behavior increases the velocity values by about 11% in the other side and by about 10% near the free surface in the case of four lines configuration and increased by about 32% above the roughness elements in a fully rough configuration.

/pdf/a-computational-fluid-dynamics-investigation-of-using-large-2s5i2mkofc.pdf

A Computational Fluid Dynamics Investigation of using Large-Scale Geometric Roughness Elements in Open Channels

Large-scale geometric roughness elements is one of the solutions that is used to protect openchannels from erosion. It is use to change the hydraulic characteristics of the flow. It may be concrete blocksor large stone placed at the bed of the channel to impose more resistance in the bed. The height of theseroughness elements is an important parameter that can affect the hydraulic characteristics of the flow. Usinga series of tests of T-shape roughness elements at three different heights, 3, 4.5, and 6cm, arranged in thefully rough configuration in order to investigate the velocity distributions along the flume. ANSYSParametric Design Language, APDL, and Computational Fluid Dynamics, CFD, were used to simulate theflow in an open channel with roughness elements. This simulation helps to find the best height of roughnesselements that can be used to change the hydraulic characteristics of the flow. The results showed that thevelocity values are decreased near the bed by about 61%, 58%, and 64% in case of 3cm, 4.5cm, and 6cmroughness heights consequently compared with the velocity of the control case. The velocity values areincreased near the free surface by about 32% and 19% in case of roughness elements height 6cm comparedwith 3cm and 4.5cm roughness heights respectively. The case of 6cm roughness height is considered to bethe effective case for decreasing the velocity values near the bed of the flume.

/pdf/investigations-on-large-scale-geometric-roughness-elements-42jsrxuev4.pdf

Iman A. Alwan

Papers

A Computational Fluid Dynamics Investigation of using Large-Scale Geometric Roughness Elements in Open Channels

Investigations on Large-Scale Geometric Roughness Elements in Open Channels with Different Heights