J. Neuhauser

Bio: J. Neuhauser is an academic researcher from Max Planck Society. The author has contributed to research in topics: ASDEX Upgrade & Divertor. The author has an hindex of 41, co-authored 205 publications receiving 5808 citations.

ELM pace making and mitigation by pellet injection in ASDEX Upgrade

Abstract: In ASDEX Upgrade, experimental efforts aim to establish pace making and mitigation of type-I edge localized modes (ELMs) in high confinement mode (H-mode) discharges. Injection of small size cryogenic deuterium pellets (~(1.4?mm)2 ? 0.2?mm ? 2.5 ? 1019?D) at rates up to 83?Hz imposed persisting ELM control without significant fuelling, enabling for investigations well inside the type-I ELM regime. The approach turned out to meet all required operational features. ELM pace making was realized with the driving frequency ranging from 1 to 2.8 times the intrinsic ELM frequency, the upper boundary set by hardware limits. ELM frequency enhancement by pellet pace making causes much less confinement reduction than by engineering means like heating, gas bleeding or plasma shaping. Confinement reduction is observed in contrast to the typical for engineering parameters. Matched discharges showed triggered ELMs ameliorated with respect to intrinsic counterparts while their frequency was increased. No significant differences were found in the ELM dynamics with the available spatial and temporal resolution. By breaking the close correlation of ELM frequency and plasma parameters, pace making allows the establishment of fELM as a free parameter giving enhanced operational headroom for tailoring H-mode scenarios with acceptable ELMs. Use was made of the pellet pace making tool in several successful applications in different scenarios. It seems that further reduction of the pellet mass could be possible, eventually resulting in less confinement reduction as well.

Identification of plasma-edge-related operational regime boundaries and the effect of edge instability on confinement in ASDEX Upgrade

Abstract: Local edge parameters on the ASDEX Upgrade tokamak are investigated at the L-mode to H-mode transition, during phases with various types of edge-localized modes (ELMs), and at the density limit. A scaling law for the boundary electron temperature, , is found which describes the H-mode threshold for deuterium-puffed discharges with favourable ion -drift direction. The region of stable operation is bounded by type I ELMs near the ideal ballooning limit and by a minimum temperature necessary to avoid thermal instability of the plasma edge. Stationary operation with type III ELMs imposes an upper limit on the edge temperature. Within the entire range of boundary densities investigated , both L-mode and H-mode are found to be accessible. During type I ELMy H-mode, a relation of global confinement with the edge pressure gradient is found which is connected with a loss of the favourable density dependence predicted by the ITER-92P and ITER-93H ELMy H-mode scalings. At high density, better confinement is achieved in H-modes with an edge pressure gradient below the ideal ballooning limit, e.g. during type III ELMy H-mode with impurity-seeded radiation.

Energy flux to the ASDEX-Upgrade diverter plates determined by thermography and calorimetry

Abstract: A new thermography system with high time resolution was put into operation at ASDEX-Upgrade and is routinely used to determine the energy flux onto the lower diverter plates. The measurements allow the power deposition to be characterized during dynamic events such as ELMs and disruptions, as well as the asymmetry of the inboard/outboard power load. A power balance is set up even during single discharges and the losses are found to be fairly equal to the power input.

High-Efficiency Plasma Refuelling by Pellet Injection from the Magnetic High-Field Side into ASDEX Upgrade

Abstract: High-efficiency refuelling of ELMy H-mode tokamak discharges with solid deuterium pellets injected from the magnetic high-field side is demonstrated. Compared to standard low-field side injection, the fuelling efficiency was enhanced by a factor of 4, the pellet penetration more than 2 times. This experimental result can be qualitatively explained by the magnetic force pushing a diamagnetic plasma cloud towards lower magnetic field, causing rapid particle loss for shallow low-field side injection, but enhancing fuelling efficiency and pellet penetration for high-field side injection.

Nonaxisymmetric energy deposition pattern on ASDEX upgrade divertor target plates during type-I edge-localized modes.

Abstract: In the ASDEX Upgrade tokamak, complex power deposition structures on the divertor target plates during type-I edge-localized modes (ELMs) have been discovered by fast (few microseconds), two-dimensional ($40\ifmmode\times\else\texttimes\fi{}40\text{ }{\mathrm{c}\mathrm{m}}^{2}$) infrared thermography. In addition to the usual axisymmetric power deposition line near the separatrix, there appear, statistically distributed, several laterally displaced and inclined stripes, mostly well separated from each other and from the main strike zone. These structures are interpreted as footprints of approximately field aligned, helical perturbations at the low field side of the main plasma edge related to the nonlinear ELM evolution. Based on this picture, the ELM related mode structure can be derived from the target load pattern, yielding on average toroidal mode numbers in a range of 8\char21{}24.

Effects of E×B velocity shear and magnetic shear on turbulence and transport in magnetic confinement devices

Abstract: One of the scientific success stories of fusion research over the past decade is the development of the ExB shear stabilization model to explain the formation of transport barriers in magnetic confinement devices. This model was originally developed to explain the transport barrier formed at the plasma edge in tokamaks after the L (low) to H (high) transition. This concept has the universality needed to explain the edge transport barriers seen in limiter and divertor tokamaks, stellarators, and mirror machines. More recently, this model has been applied to explain the further confinement improvement from H (high)-mode to VH (very high)-mode seen in some tokamaks, where the edge transport barrier becomes wider. Most recently, this paradigm has been applied to the core transport barriers formed in plasmas with negative or low magnetic shear in the plasma core. These examples of confinement improvement are of considerable physical interest; it is not often that a system self-organizes to a higher energy state with reduced turbulence and transport when an additional source of free energy is applied to it. The transport decrease that is associated with ExB velocity shear effects also has significant practical consequences for fusion research. The fundamental physics involved in transport reduction is the effect of ExB shear on the growth, radial extent and phase correlation of turbulent eddies in the plasma. The same fundamental transport reduction process can be operational in various portions of the plasma because there are a number ways to change the radial electric field Er. An important theme in this area is the synergistic effect of ExB velocity shear and magnetic shear. Although the ExB velocity shear appears to have an effect on broader classes of microturbulence, magnetic shear can mitigate some potentially harmful effects of ExB velocity shear and facilitate turbulence stabilization.

Plasma{material interactions in current tokamaks and their implications for next step fusion reactors

Abstract: The major increase in discharge duration and plasma energy in a next step DT fusion reactor will give rise to important plasma-material effects that will critically influence its operation, safety and performance. Erosion will increase to a scale of several centimetres from being barely measurable at a micron scale in today's tokamaks. Tritium co-deposited with carbon will strongly affect the operation of machines with carbon plasma facing components. Controlling plasma-wall interactions is critical to achieving high performance in present day tokamaks, and this is likely to continue to be the case in the approach to practical fusion reactors. Recognition of the important consequences of these phenomena stimulated an internationally co-ordinated effort in the field of plasma-surface interactions supporting the Engineering Design Activities of the International Thermonuclear Experimental Reactor project (ITER), and significant progress has been made in better understanding these issues. The paper reviews the underlying physical processes and the existing experimental database of plasma-material interactions both in tokamaks and laboratory simulation facilities for conditions of direct relevance to next step fusion reactors. Two main topical groups of interaction are considered: (i) erosion/redeposition from plasma sputtering and disruptions, including dust and flake generation and (ii) tritium retention and removal. The use of modelling tools to interpret the experimental results and make projections for conditions expected in future devices is explained. Outstanding technical issues and specific recommendations on potential R&D avenues for their resolution are presented.

Chapter 3: MHD stability, operational limits and disruptions

Abstract: Progress in the area of MHD stability and disruptions, since the publication of the 1999 ITER Physics Basis document (1999 Nucl. Fusion 39 2137-2664), is reviewed. Recent theoretical and experimental research has made important advances in both understanding and control of MHD stability in tokamak plasmas. Sawteeth are anticipated in the ITER baseline ELMy H-mode scenario, but the tools exist to avoid or control them through localized current drive or fast ion generation. Active control of other MHD instabilities will most likely be also required in ITER. Extrapolation from existing experiments indicates that stabilization of neoclassical tearing modes by highly localized feedback-controlled current drive should be possible in ITER. Resistive wall modes are a key issue for advanced scenarios, but again, existing experiments indicate that these modes can be stabilized by a combination of plasma rotation and direct feedback control with non-axisymmetric coils. Reduction of error fields is a requirement for avoiding non-rotating magnetic island formation and for maintaining plasma rotation to help stabilize resistive wall modes. Recent experiments have shown the feasibility of reducing error fields to an acceptable level by means of non-axisymmetric coils, possibly controlled by feedback. The MHD stability limits associated with advanced scenarios are becoming well understood theoretically, and can be extended by tailoring of the pressure and current density profiles as well as by other techniques mentioned here. There have been significant advances also in the control of disruptions, most notably by injection of massive quantities of gas, leading to reduced halo current fractions and a larger fraction of the total thermal and magnetic energy dissipated by radiation. These advances in disruption control are supported by the development of means to predict impending disruption, most notably using neural networks. In addition to these advances in means to control or ameliorate the consequences of MHD instabilities, there has been significant progress in improving physics understanding and modelling. This progress has been in areas including the mechanisms governing NTM growth and seeding, in understanding the damping controlling RWM stability and in modelling RWM feedback schemes. For disruptions there has been continued progress on the instability mechanisms that underlie various classes of disruption, on the detailed modelling of halo currents and forces and in refining predictions of quench rates and disruption power loads. Overall the studies reviewed in this chapter demonstrate that MHD instabilities can be controlled, avoided or ameliorated to the extent that they should not compromise ITER operation, though they will necessarily impose a range of constraints.

Chapter 1: Overview and summary

Abstract: The ITER Physics Basis presents and evaluates the physics rules and methodologies for plasma performance projections, which provide the basis for the design of a tokamak burning plasma device whose goal is to demonstrate the scientific and technological feasibility of fusion energy for peaceful purposes. This Chapter summarizes the physics basis for burning plasma projections, which is developed in detail by the ITER Physics Expert Groups in subsequent chapters. To set context, the design guidelines and requirements established in the report of ITER Special Working Group 1 are presented, as are the specifics of the tokamak design developed in the Final Design Report of the ITER Engineering Design Activities, which exemplifies burning tokamak plasma experiments. The behaviour of a tokamak plasma is determined by the interaction of many diverse physics processes, all of which bear on projections for both a burning plasma experiment and an eventual tokamak reactor. Key processes summarized here are energy and particle confinement and the H-mode power threshold; MHD stability, including pressure and density limits, neoclassical islands, error fields, disruptions, sawteeth, and ELMs; power and particle exhaust, involving divertor power dispersal, helium exhaust, fuelling and density control, H-mode edge transition region, erosion of plasma facing components, tritium retention; energetic particle physics; auxiliary power physics; and the physics of plasma diagnostics. Summaries of projection methodologies, together with estimates of their attendant uncertainties, are presented in each of these areas. Since each physics element has its own scaling properties, an integrated experimental demonstration of the balance between the combined processes which obtains in a reactor plasma is inaccessible to contemporary experimental facilities: it requires a reactor scale device. It is argued, moreover, that a burning plasma experiment can be sufficiently flexible to permit operation in a steady state mode, with non-inductive plasma current drive, as well as in a pulsed mode where current is inductively driven. Overall, the ITER Physics Basis can support a range of candidate designs for a tokamak burning plasma facility. For each design, there will remain a significant uncertainty in the projected performance, but the projection methodologies outlined here do suffice to specify the major parameters of such a facility and form the basis for assuring that its phased operation will return sufficient information to design a prototype commercial fusion power reactor, thus fulfilling the goal of the ITER project.

Chapter 4: Power and particle control

Abstract: Progress, since the ITER Physics Basis publication (ITER Physics Basis Editors et al 1999 Nucl. Fusion 39 2137–2664), in understanding the processes that will determine the properties of the plasma edge and its interaction with material elements in ITER is described. Experimental areas where significant progress has taken place are energy transport in the scrape-off layer (SOL) in particular of the anomalous transport scaling, particle transport in the SOL that plays a major role in the interaction of diverted plasmas with the main-chamber material elements, edge localized mode (ELM) energy deposition on material elements and the transport mechanism for the ELM energy from the main plasma to the plasma facing components, the physics of plasma detachment and neutral dynamics including the edge density profile structure and the control of plasma particle content and He removal, the erosion of low- and high-Z materials in fusion devices, their transport to the core plasma and their migration at the plasma edge including the formation of mixed materials, the processes determining the size and location of the retention of tritium in fusion devices and methods to remove it and the processes determining the efficiency of the various fuelling methods as well as their development towards the ITER requirements. This experimental progress has been accompanied by the development of modelling tools for the physical processes at the edge plasma and plasma–materials interaction and the further validation of these models by comparing their predictions with the new experimental results. Progress in the modelling development and validation has been mostly concentrated in the following areas: refinement in the predictions for ITER with plasma edge modelling codes by inclusion of detailed geometrical features of the divertor and the introduction of physical effects, which can play a major role in determining the divertor parameters at the divertor for ITER conditions such as hydrogen radiation transport and neutral–neutral collisions, modelling of the ion orbits at the plasma edge, which can play a role in determining power deposition at the divertor target, models for plasma–materials and plasma dynamics interaction during ELMs and disruptions, models for the transport of impurities at the plasma edge to describe the core contamination by impurities and the migration of eroded materials at the edge plasma and its associated tritium retention and models for the turbulent processes that determine the anomalous transport of energy and particles across the SOL. The implications for the expected performance of the reference regimes in ITER, the operation of the ITER device and the lifetime of the plasma facing materials are discussed.