Jaana Sorvari

Abstract: In Finland, shooting ranges are among the most common activities causing soil contamination. According to our study based on questionnaires and previous regional surveys, the total number of Finnish outdoor shooting ranges is between 2000 and 2500. Most of the ranges are small and only ca. 5% exceed 20 ha. Almost a third of the ranges can cause a groundwater pollution risk, while only few cause an immediate health risk. In the first instance, 50-60 shooting ranges identified as being high-risk areas should be investigated in detail. At present, the risk management options at Finnish shooting ranges are very limited. Hence, soil excavation combined with disposal is the most common remediation technique. Some of the remediation methods used in other countries have been proven unsuitable in Finnish conditions. Therefore, new, feasible, cost-effective and economical remediation technologies are needed. To exclude future contamination, a total ban of lead shot would be the most effective way.

Abstract: The EC 50 values (24h, Daphnia magna ) of Fe 3+ , Cu 2+ , Mn 2+ , Zn 2+ , Cd 2+ and Hg 2+ complexed by EDTA or DTPA were compared with those of the respective uncomplexed metals and free EDTA and DTPA. The experiments gave the following toxicity order: Hg 2+ > Cu 2+ > Cd 2+ > Zn 2+ > Fe 3+ > Mn 2+ . After complexation, the toxicities were 1.1 – 1700 (EDTA) and 7.0 – 3400 (DTPA) times lower. With Hg 2+ however, complexation did not decrease the toxicity. Excluding Cd-DTPA, the toxicity reductions had a high correlation with the conditional stability constants of the respective metal chelates. Compared with the toxicity of free EDTA and DTPA, metal complexation increased the toxicity of EDTA and DTPA considerably. The results of the previous Microtox ® study were well in accordance with this investigation.

Abstract: From the late 1950s to the early 1970s elastic polysulphide sealants were used in outdoor seams between concrete blocks in prefabricated buildings. The sealants contained 5-30% polychlorinated biphenyls (PCBs). Due to the weathering of sealants in general and the replacement of seams with new PCB-free materials in the 1990s, PCBs have drifted to the soil adjacent to buildings. The objectives of this study were to survey PCB contamination in the surroundings of former PCB-containing buildings and to evaluate the risks to human health. Samples from soil, and also from blood serum of residents, were collected to obtain data for exposure assessment. The health risk assessment was based on deterministic and probabilistic calculations for cancer and non-cancer risks. Soil ingestion and dermal contact were considered the main routes of exposure and children the most important exposed group. The mean total PCB concentration was 6.83 mg/kg within 2m of the buildings and 0.52 mg/kg within 3-10 m from of the buildings. The deterministic risk assessment with conservative parameters resulted in lifetime cancer risk estimates on the order of 10(-6)-10(-7). The lifetime average daily dose (LADD) for PCBs was less than 10% of the reference dose (RfD) 0.02 microg/kg day, which is based on immunosupression in monkeys. The LADD corresponding to the total site attributable exposure was less than 10% of the estimated average dietary PCB intake in Finland. Children can, however, in worst cases be exposed to daily doses near the level of the RfD. Low cost measures are recommended to reduce possible exposure of children.

Abstract: The decisions on risk management (RM) of contaminated sites in Finland have typically been driven by practical factors such as time and money. However, RM is a multifaceted task that generally involves several additional determinants, e.g. performance and environmental effects of remediation methods, psychological and social factors. Therefore, we adopted a multi-criteria decision analysis approach and developed a decision support tool (DST) that is viable in decision-making in such a complex situation. The basic components of the DST are based on the Dutch REC system. However, our DST is more case-specific and allows the consideration of the type, magnitude and scale of contamination, land use, environmental conditions and socio-cultural aspects (e.g. loss of cultural heritage, image aspects). The construction of the DST was started by structuring the decision problem using a value tree. Based on this work we adopted the Multi-Attribute Value Theory (MAVT) for data aggregation. The final DST was demonstrated by two model sites for which the RM alternatives and site-specific data were created on the basis of factual remediation projects and by interviewing experts. The demonstration of the DST was carried out in a workshop where representatives of different stakeholders were requested to rank and weight the decision criteria involved. To get information on the consistency of the ranking of the RM alternatives, we used different weighting techniques (ratio estimation and pair-wise weighting) and alternative ways to treat individual respondents' weights in calculating the preference scores for each RM alternative. These dissimilar approaches resulted in some differences in the preference order of the RM alternatives. The demonstration showed that attention has to be paid to the proper description of the site, the principles of the procedure and the decision criteria. Nevertheless, the procedure proved to enable efficient communication between different stakeholders and the identification of the preferred RM option.

Abstract: In Finland the number of potentially contaminated sites totals ca. 20 000. The annual costs of remediation are 60-70 million euros. Excavation combined with disposal or off-site treatment is the most common soil remediation method. To define which factors make contaminated land management (CLM) eco-efficient and to study whether eco-efficiency has been considered in CLM decisions we carried out a literature survey, two stakeholder seminars, thematic interviews and a questionnaire study on economic instruments. Generally speaking, eco-efficiency means gaining environmental benefits with fewer resources. To assess its realization in CLM, it is necessary to have a more specific definition. In our study, we arrived at a list of several qualifications for eco-efficiency. It was also shown that eco-efficiency has hardly been a real issue in the selection of remediation techniques or generally, in the decision-making concerning contaminated sites. The existing policy instruments seem to be insufficient to promote eco-efficiency in CLM. Several concrete barriers to eco-efficiency also came up, urgency and lack of money being the most important. The scarcity of the use of in situ remediation methods and the difficulties involved in recycling slightly contaminated or treated soil were considered to be major problems. Insufficient site studies, inadequate or unsuitable methods for risk assessment and cost evaluation, and deficient and mistimed risk communication can also hinder the realization of eco-efficiency. Hence, there is a need to promote the use of more eco-efficient remediation techniques and to develop CLM policy instruments, guidelines, and participatory processes and methods to assess the eco-efficiency of CLM options.

Abstract: Sustainability assessment is being increasingly viewed as an important tool to aid in the shift towards sustainability. However, this is a new and evolving concept and there remain very few examples of effective sustainability assessment processes implemented anywhere in the world. Sustainability assessment is often described as a process by which the implications of an initiative on sustainability are evaluated, where the initiative can be a proposed or existing policy, plan, programme, project, piece of legislation, or a current practice or activity. However, this generic definition covers a broad range of different processes, many of which have been described in the literature as 'sustainability assessment'. This article seeks to provide some clarification by reflecting on the different approaches described in the literature as being forms of sustainability assessment, and evaluating them in terms of their potential contributions to sustainability. Many of these are actually examples of 'integrated assessment', derived from environmental impact assessment (EIA) and strategic environmental assessment (SEA), but which have been extended to incorporate social and economic considerations as well as environmental ones, reflecting a 'triple bottom line' (TBL) approach to sustainability. These integrated assessment processes typically either seek to minimise 'unsustainability', or to achieve TBL objectives. Both aims may, or may not, result in sustainable practice. We present an alternative conception of sustainability assessment, with the more ambitious aim of seeking to determine whether or not an initiative is actually sustainable. We term such processes 'assessment for sustainability'. 'Assessment for sustainability' firstly requires that the concept of sustainability be well-defined. The article compares TBL approaches and principles-based approaches to developing such sustainability criteria, concluding that the latter are more appropriate, since they avoid many of the inherent limitations of the triple-bottom-line as a conception of sustainability.

Abstract: The occurrence of new emerging contaminants in surface waters has recently grabbed increased attention of the scientific community. The adoption of Advanced Oxidation Processes (AOPs) represents an efficient strategy to remove recalcitrant compounds from aqueous streams and achieve high mineralization levels. Amongst AOPs, the photo-Fenton process has been widely investigated due to the possibility of using a renewable energy source (i.e., solar energy) and low concentration of catalyst. On the other hand, the use of photo-Fenton process is restricted to acidic pH values, with associate high operating costs for industrial scale applications. To overcome these drawbacks, photo-Fenton processes modified by adding selected chelating agents can be successfully performed at neutral pH. The present review aims at examining and comparing the most relevant papers dealing with photo-Fenton processes at neutral pH that appeared in the literature so far. Such papers were classified by chelating species adopted. In particular, for each iron(III)-ligand complex, the mechanism of photolysis, the speciation diagram, the light absorption properties, the quantum yields, biodegradation and toxicity, and some example of applications are reported. As a conclusion, suitable criteria for choosing chelating agent and operating conditions in photo-Fenton processes at neutral pH are proposed.

Abstract: The degradation of the organic content of a bleaching Kraft mill effluent (BKME) has been carried out by using Fenton reagent and irradiation providing the conditions needed for the simultaneous occurrence of Fenton and photo-Fenton reactions. The main parameters that govern the complex reactive system, i.e. light intensity, temperature, pH, Fe(II) and H 2 O 2 initial concentrations, and O 2 presence in solution have been studied. Concentrations of Fe(II) between 0 and 800 ppm, and H 2 O 2 between 0 and 10,000 ppm were chosen. Temperatures above 25 and up to 70 °C have a beneficial effect on total organic carbon (TOC) decay rate. The presence of small amounts of O 2 seems to be enough to ensure the reaction progress. The combination of Fenton and photo-Fenton reactions has been proved to be highly effective for the treatment of such a type of wastewaters, and important advantages concerning the application of this combination of reactions arise from the study.

Abstract: The present study was conducted to investigate the levels and sources of heavy metals (Cu, Cr, Cd, Pb, Zn, Hg and As) and persistent organic compounds including polycyclic aromatic hydrocarbons (PAHs) and polychlorinated biphenyls (PCBs) in soils taken from Wenling, an emerging e-waste recycling city in Taizhou, China. The results suggested that most heavy metals exceeded the respective Grade II value of soil quality standards from State Environmental Protection Administration of China and also exceeded the Dutch optimum values. Total PAHs in soil ranged from 371.8 to 1231.2 microg/kg, and relatively higher PAHs concentrations were found in soils taken from simple household workshops. PCBs were detectable in all samples with total concentrations ranging from 52.0 to 5789.5 microg/kg, which were 2.1-232.5 times higher than that from the reference site (24.9 microg/kg). Results of this study suggested soil in the Wenling e-waste recycling area were heavily contaminated by heavy metals, PAHs and PCBs. Furthermore, compared with large-scale plants, simple household workshops contributed more heavy metals, PAHs and PCBs pollution to the soil environment, indicating that soil contamination from e-waste recycling in simple household workshops should be given more attention.

Abstract: Background, aim, and scope In the 50 years or so that polychlorinated biphenyls (PCBs) were manufactured in the USA and elsewhere, they were widely used in numerous applications because of their desirable properties. The purpose of this paper is to review and summarize in one place the factual information about the uses of PCBs, as well as to correct some misconceptions that have arisen over the years. The focus is on applications in the USA for which there is ample documentation. However, use patterns were probably similar worldwide.