Jacopo Buongiorno

Bio: Jacopo Buongiorno is an academic researcher from Massachusetts Institute of Technology. The author has contributed to research in topics: Boiling & Nanofluid. The author has an hindex of 40, co-authored 170 publications receiving 12125 citations. Previous affiliations of Jacopo Buongiorno include Electric Power Research Institute & Tokyo Electric Power Company.

Alumina Nanoparticle Pre-coated Tubing Ehancing Subcooled Flow Boiling Cricital Heat Flux

Abstract: Nanofluids are engineered colloidal dispersions of nano-sized particle in common base fluids. Previous pool boiling studies have shown that nanofluids can improve critical heat flux (CHF) up to 200% for pool boiling and up to 50% for subcooled flow boiling due to the boiling induced nanoparticle deposition on the heated surface. Motivated by the significant CHF enhancement of nanoparticle deposited surface, this study investigated experimentally the subcooled flow boiling heat transfer of pre-coated test sections in water. Using a separate coating loop, stainless steel test sections were treated via flow boiling of alumina nanofluids at constant heat flux and mass flow rate. The pre-coated test sections were then used in another loop to measure subcooled flow boiling heat transfer coefficient and CHF with water. The CHF values for the pre-coated tubing were found on average to be 28% higher than bare tubing at high mass flux G = 2500 kg/m2 s. However, no enhancement was found at lower mass flux G = 1500 kg/m2 s. The heat transfer coefficients did not differ much between experiments when the bare or coated tubes were used. SEM images of the test sections confirm the presence of a nanoparticle coating layer. The nanoparticle deposition is sporadic and no relationship between the coating pattern and the amount of CHF enhancement is observed.Copyright © 2009 by ASME

Effect of Nanoparticle Deposition on Rewetting Temperature and Quench Velocity in Experiments With Stainless Steel Rodlets and Nanofluids

Abstract: Quenching of small stainless steel rods in pure water and nanofluids with alumina and diamond nanoparticles at low concentrations (0.1 vol%) was investigated experimentally. The rods were heated to an initial temperature of ∼1000 °C and then plunged into the test fluid. The results show that the quenching behavior of the nanofluids is nearly identical to that of pure water. However, due to nanofluids boiling during the quenching process, some nanoparticles deposit on the surface of the rod, which results in much higher quenching rate in subsequent tests with the same rod. It is likely that particle deposition destabilizes the film-boiling vapor film at high temperature, thus causing the quenching process to accelerate, as evident from the values of the quench front speed measured by means of a high-speed camera. The acceleration strongly depends on the nanoparticle material used, i.e., the alumina nanoparticles on the surface significantly improve the quenching, while the diamond nanoparticles do not. The possible mechanisms responsible for the quench front acceleration are discussed. It is found that the traditional concept of conduction-controlled quenching cannot explain the acceleration provided by the nanoparticle layer on the surface.Copyright © 2009 by ASME

Plug Design for Deep Borehole Disposal of High-Level Nuclear Waste

Abstract: This paper focuses on the improvement of the longevity and robustness of materials for sealing and plugging the upper portion of a deep borehole used for permanent isolation of high-level nuclear waste. Analytical models of porous and laminar flows show that even when materials have low intrinsic permeability, micron-sized cracks and gaps between the plug and rock (formed via chemical reaction, shrinkage, osmotic consolidation, etc.) significantly diminish the plug’s sealing properties. On this basis, materials such as asphalt, traditional cements, and pure bentonite—which crack or shrink under certain conditions—are unfavorable. An ongoing test program has formulated expanding cement mixtures containing MgO to prevent such bypass flow. Furthermore, these findings support using stable, malleable, and low-permeability plug material (k ≤ 10-16 m2), such as a crushed rock (70%) and bentonite (30%) mixture. Alternative clays such as sepiolite could be blended with the bentonite to further reduce the p...

Climate change 2014 - Mitigation of climate change

Abstract: The talk with present the key results of the IPCC Working Group III 5th assessment report. Concluding four years of intense scientific collaboration by hundreds of authors from around the world, the report responds to the request of the world's governments for a comprehensive, objective and policy neutral assessment of the current scientific knowledge on mitigating climate change. The report has been extensively reviewed by experts and governments to ensure quality and comprehensiveness.

World energy outlook

Abstract: This chapter discusses leading problems linked to energy that the world is now confronting and to propose some ideas concerning possible solutions. Oil deserves special attention among all energy sources. Since the beginning of 1981, it has merely been continuing and enhancing the downward movement in consumption and prices caused by excessive rises, especially for light crudes such as those from Africa, and the slowing down of worldwide economic growth. Densely-populated oil-producing countries need to produce to live, to pay for their food and their equipment. If the economic growth of the industrialized countries were to be 4%, even if investment in the rational use of energy were pushed to the limit and the development of nonpetroleum energy sources were also pursued actively, it would be extremely difficult to prevent a sharp rise in prices. It is evident that it is absolutely necessary to pursue actively the development of coal, natural gas, and nuclear power if a physical shortage of energy is not to block economic growth.

A review on nanofluids: preparation, stability mechanisms, and applications

Abstract: Nanofluids, the fluid suspensions of nanomaterials, have shown many interesting properties, and the distinctive features offer unprecedented potential for many applications. This paper summarizes the recent progress on the study of nanofluids, such as the preparation methods, the evaluation methods for the stability of nanofluids, and the ways to enhance the stability for nanofluids, the stability mechanisms of nanofluids, and presents the broad range of current and future applications in various fields including energy and mechanical and biomedical fields. At last, the paper identifies the opportunities for future research.