In the previous paper Ralph Brodd and Martin Winter described the different kinds of batteries and fuel cells. In this paper I will describe lithium batteries in more detail, building an overall foundation for the papers that follow which describe specific components in some depth and usually with an emphasis on the materials behavior. The lithium battery industry is undergoing rapid expansion, now representing the largest segment of the portable battery industry and dominating the computer, cell phone, and camera power source industry. However, the present secondary batteries use expensive components, which are not in sufficient supply to allow the industry to grow at the same rate in the next decade. Moreover, the safety of the system is questionable for the large-scale batteries needed for hybrid electric vehicles (HEV). Another battery need is for a high-power system that can be used for power tools, where only the environmentally hazardous Ni/ Cd battery presently meets the requirements. A battery is a transducer that converts chemical energy into electrical energy and vice versa. It contains an anode, a cathode, and an electrolyte. The anode, in the case of a lithium battery, is the source of lithium ions. The cathode is the sink for the lithium ions and is chosen to optimize a number of parameters, discussed below. The electrolyte provides for the separation of ionic transport and electronic transport, and in a perfect battery the lithium ion transport number will be unity in the electrolyte. The cell potential is determined by the difference between the chemical potential of the lithium in the anode and cathode, ∆G ) -EF. As noted above, the lithium ions flow through the electrolyte whereas the electrons generated from the reaction, Li ) Li+ + e-, go through the external circuit to do work. Thus, the electrode system must allow for the flow of both lithium ions and electrons. That is, it must be both a good ionic conductor and an electronic conductor. As discussed below, many electrochemically active materials are not good electronic conductors, so it is necessary to add an electronically conductive material such as carbon * To whom correspondence should be addressed. Phone and fax: (607) 777-4623. E-mail: stanwhit@binghamton.edu. 4271 Chem. Rev. 2004, 104, 4271−4301

http://www.chemie.uni-regensburg.de/Anorganische_Chemie/Vortrag/StudentenWS06-07/Vortrag_Amereller.pdf

Lithium Batteries and Cathode Materials

Electrochemical energy storage technology is based on devices capable of exhibiting high energy density (batteries) or high power density (electrochemical capacitors). There is a growing need, for current and near-future applications, where both high energy and high power densities are required in the same material. Pseudocapacitance, a faradaic process involving surface or near surface redox reactions, offers a means of achieving high energy density at high charge–discharge rates. Here, we focus on the pseudocapacitive properties of transition metal oxides. First, we introduce pseudocapacitance and describe its electrochemical features. Then, we review the most relevant pseudocapacitive materials in aqueous and non-aqueous electrolytes. The major challenges for pseudocapacitive materials along with a future outlook are detailed at the end.

https://hal.archives-ouvertes.fr/hal-01171774/document

Pseudocapacitive oxide materials for high-rate electrochemical energy storage

The development of novel materials is a fundamental focal point of chemical research; and this interest is mandated by advancements in all areas of industry and technology. A good example of the synergism between scientific discovery and technological development is the electronics industry, where discoveries of new semiconducting materials resulted in the evolution from vacuum tubes to diodes and transistors, and eventually to miniature chips. The progression of this technology led to the development * To whom correspondence should be addressed. B.L.C.: (504) 2801385 (phone); (504) 280-3185 (fax); bcushing@uno.edu (e-mail). C.J.O.: (504)280-6846(phone);(504)280-3185(fax);coconnor@uno.edu (e-mail). 3893 Chem. Rev. 2004, 104, 3893−3946

http://depa.fquim.unam.mx/amyd//archivero/FidelmarLechugaSanabria_4940.pdf

Recent advances in the liquid-phase syntheses of inorganic nanoparticles.

Sol-gel chemistry of transition metal oxides

The Hydrothermal Synthesis of Zeolites: History and Development from the Earliest Days to the Present Time

Vanadium pentoxide gels

Synthesis of polyoxovanadates via “chimie douce”

Vanadium pentoxide gels consist of entangled polymeric fibers. Electron diffraction experiments have shown that these fibers are actually arranged as flat ribbons about 103 A long, 102 A wide, and 10 A thick. A two-dimensional order is observed along these ribbons which does not vary upon swelling. The two-dimensional cell parameters a = 27.0 A and b = 3.6A suggest that the organization within the fibers is closely related to the lamellar structure of orthorhombic V2O5. The fiber is made of basic blocks containing 10 vanadium atoms along the a direction. These blocks seem to be linked together by water molecules which are strongly bonded to the structure and cannot be removed without crystallization of the xerogel into orthorhombic V2O5.

Jacques Livage

Papers

Vanadium pentoxide gels

Synthesis of polyoxovanadates via “chimie douce”

Vanadium pentoxide gels

Sol-gel chemistry from metal alkoxide precursors

Sol-gel chemistry and electrochemical properties of vanadium oxide gels