James H. Tutt

Bio: James H. Tutt is an academic researcher from Pennsylvania State University. The author has contributed to research in topics: Spectrometer & Grating. The author has an hindex of 12, co-authored 71 publications receiving 549 citations. Previous affiliations of James H. Tutt include Open University & University of Iowa.

First results from a next-generation off-plane X-ray diffraction grating

Abstract: Future NASA X-ray spectroscopy missions will require high throughput, high resolving power grating spectrometers Off-plane reflection gratings are capa- ble of meeting the performance requirements needed to realize the scientific goals of these missions We have identified a novel grating fabrication method that utilizes common lithographic and microfabrication techniques to produce the high fidelity groove profile necessary to achieve this performance Application of this process has produced an initial pre-master that exhibits a radial (variable line spacing along the groove dimension), high density (>6000 grooves/mm), laminar profile This pre- master has been tested for diffraction efficiency at the BESSY II synchrotron light facility and diffracts up to 55 % of incident light into usable spectral orders Fur- thermore, tests of spectral resolving power show that these gratings are capable of obtaining resolving powers well above 1300 (λ/�λ ) with limitations due to the test apparatus, not the gratings Obtaining these results has provided confidence that this

Mitigating radiation-induced charge transfer inefficiency in full-frame CCD applications by 'pumping' traps

Abstract: The charge transfer efficiency of a CCD is based on the average level of signal lost per pixel over a number of transfers. This value can be used to directly compare the relative performances of different structures, increases in radiation damage or to quantify improvements in operating parameters. This number does not however give sufficient detail to mitigate for the actual signal loss/deference in either of the transfer directions that may be critical to measuring shapes to high accuracy, such as those required in astronomy applications (e.g. for Gaia’s astrometry or the galaxy distortion measurements for Euclid) based in the radiation environment of space. Pocket-pumping is an established technique for finding the location and activation levels of traps; however, a number of parameters in the process can also be explored to identify the trap species and location to sub-pixel accuracy. This information can be used in two ways to increase the sensitivity of a camera. Firstly, the clocking process can be optimised for the time constant of the majority of traps in each of the transfer directions, reducing deferred charge during read out. Secondly, a correction algorithm can be developed and employed during the post-processing of individual frames to move most of any deferred signal back into the charge packet it originated from. Here we present the trap-pumping techniques used to optimise the charge transfer efficiency of p- and n-channel e2v CCD204s and describe the use of trap-pumped images for on-orbit calibration and ground based image correction algorithms.

Lynx Mission Concept Status

Abstract: Lynx is a concept under study for prioritization in the 2020 Astrophysics Decadal Survey. Providing orders of magnitude increase in sensitivity over Chandra, Lynx will examine the first black holes and their galaxies, map the large-scale structure and galactic halos, and shed new light on the environments of young stars and their planetary systems. In order to meet the Lynx science goals, the telescope consists of a high-angular resolution optical assembly complemented by an instrument suite that may include a High Definition X-ray Imager, X-ray Microcalorimeter and an X-ray Grating Spectrometer. The telescope is integrated onto the spacecraft to form a comprehensive observatory concept. Progress on the formulation of the Lynx telescope and observatory configuration is reported in this paper.

The Noise Performance of Electron-Multiplying Charge-Coupled Devices at X-ray Energies

Abstract: Electron-multiplying charge-coupled devices (EM-CCDs) are used in low-light-level (L3) applications for detecting optical, ultraviolet, and near-infrared photons (10-1100 nm). The on-chip gain process is able to increase the detectability of any signal collected by the device through the multiplication of the signal before the output node. Thus, the effective readout noise can be reduced to subelectron levels, allowing the detection of single photons. However, this gain process introduces an additional noise component due to the stochastic nature of the multiplication. In optical applications, this additional noise has been characterized. The broadening of the detected peak is described by the excess noise factor. This factor tends to a value of √{2} at high gain (>; 100x). In X-ray applications, the situation is improved by the effect that Fano factor f has on the shot noise associated with X-ray photon detection (f ≈ 0.12 at X-ray energies). In this paper, the effect of the detection of X-ray photons in silicon is assessed both analytically and through a Monte Carlo model of the gain amplification process. The excess noise on the signal is predicted (termed the modified Fano factor) for photon detection in an EM-CCD at X-ray energies. A hypothesis is made that the modified Fano factor should tend to 1.115 at high levels of gain (>; 10x). In order to validate the predictions made, measurements were taken using an 55Fe source with Mn k-alpha X-ray energy of 5898 eV. These measurements allowed the hypothesis to be verified.

Improving the spatial resolution of soft X-ray detection using an Electron-Multiplying Charge-Coupled Device

Abstract: The Super Advanced X-ray Emission Spectrometer (SAXES) is an instrument at the Swiss Light Source designed for Resonant Inelastic X-ray Scattering with an energy resolution (E/ΔE) better than 12000 at 930 eV. Improvements to the instrument have been predicted that could allow the energy resolution to be improved by a factor of two. To achieve this, the spatial resolution of the detector (currently a Charge-Coupled Device, CCD) over which the energy spectrum is dispersed would have to be improved to better than 5 μm. X-ray photons with energies between a few hundred to a few thousand electron volts primarily interact within the field-free region of back-illuminated CCDs, where each photon forms an electron cloud that diffuses isotropically before reaching the depleted region close to the electrodes. Each photon's electron cloud is likely to be detected as an event with signal split across multiple pixels. Analysing these split events using centroiding techniques allows the photon's interaction position to be determined to a sub-pixel level. PolLux is a soft X-ray microspectroscopy endstation at the Swiss Light Source that can focus 200 eV to 1200 eV X-rays to a spot size of approximately 20 nm. Previous studies using data taken with a linear scan across the centre of a pixel in 3 μm steps predicted an improved resolution by applying centroiding techniques and using an Electron-Multiplying CCD (EM-CCD). In this study, a full 2D map of the centroiding accuracy in the pixel is presented, formed by rastering in two dimensions across the image plane in single micron steps. The improved spatial resolution from centroiding events in the EM-CCD in all areas of the pixel over the standard CCD is attributed to the improved signal to noise ratio provided by the multiplication register even at high pixel readout speeds (tens of MHz).

XMM-Newton observatory*: I. The spacecraft and operations. Commentary

Abstract: The XMM-Newton Observatory is a cornerstone mission of the European Space Agency's Horizon 2000 programme, and is the largest scientific satellite it has launched to date. This paper summarises the principal characteristics of the Observatory which are pertinent to scientific operations. The scientific results appearing in this issue have been enabled by the unprecedentedly large effective area of the three mirror modules, which are briefly described. The in-orbit performance and preliminary calibrations of the observatory are briefly summarised. The observations from the XMM-Newton calibration and performance verification phase, which are public and from which most papers in this issue have been derived, are listed. The flow of data from the spacecraft, through the ground segment, to the production of preliminary science products supplied to users is also discussed.

Photon counting strategies with low light level CCDs

Abstract: Low light level charge coupled devices (L3CCDs) have recently been developed, incorporating on-chip gain. They may be operated to give an effective readout noise much less than one electron by implementing an on-chip gain process allowing the detection of individual photons. However, the gain mechanism is stochastic and so introduces significant extra noise into the system. In this paper we examine how best to process the output signal from an L3CCD so as to minimize the contribution of stochastic noise, while still maintaining photometric accuracy. We achieve this by optimising a transfer function which translates the digitised output signal levels from the L3CCD into a value approximating the photon input as closely as possible by applying thresholding techniques. We identify several thresholding strategies and quantify their impact on photon counting accuracy and effective signal-to-noise. We find that it is possible to eliminate the noise introduced by the gain process at the lowest light levels. Reduced improvements are achieved as the light level increases up to about twenty photons per pixel and above this there is negligible improvement. Operating L3CCDs at very high speeds will keep the photon flux low, giving the best improvements in signal-to-noise ratio.

2016 Atomic Spectrometry Update – a review of advances in X-ray fluorescence spectrometry and its applications

Abstract: This review describes advances in the XRF group of techniques published approximately between April 2015 and March 2016. Fundamental contributions in the instrumentation sections include the development of synchrotron radiation sources, semiconductor design technology and evaluating the quality of in situ hand-held XRF results. A bench top TXRF spectrometer for the measurement of the elements from carbon to uranium is described that offers achievable detection limits that range from ng g−1 to μg g−1. The applications sections aim to give a representative overview of the range of applications that use XRF techniques with an emphasis on papers that describe technical or application innovation. Sample size investigated ranged from the planet Mercury down to nano-gram quantities of cement secreted by settlement stage barnacle larvae. The archaeological and cultural heritage section this year includes an authentic report on the use of cannabis as a filler in ancient lime plaster and heartening news that the construction of an underground parking garage in the centre of Zurich (Switzerland) unearthed the remains of seven Neolithic settlements from the 4th and 3rd millennium BC. The X-ray excitation of iron present in ancient iron-gall inks was presented as a step toward the non-invasive reading of fragile and/or unopenable documents. Feedback from readers of this review is most welcome and the review coordinator may be contacted using the email address provided.

Technology advancement of the CCD201-20 EMCCD for the WFIRST coronagraph instrument: sensor characterization and radiation damage

Abstract: The Wide Field InfraRed Survey Telescope-Astrophysics Focused Telescope Asset (WFIRST-AFTA) mission is a 2.4-m class space telescope that will be used across a swath of astrophysical research domains. JPL will provide a high-contrast imaging coronagraph instrument - one of two major astronomical instruments. In order to achieve the low noise performance required to detect planets under extremely low flux conditions, the electron multiplying charge-coupled device (EMCCD) has been baselined for both of the coronagraph's sensors - the imaging camera and integral field spectrograph. JPL has established an EMCCD test laboratory in order to advance EMCCD maturity to technology readiness level-6. This plan incorporates full sensor characterization, including read noise, dark current, and clock-induced charge. In addition, by considering the unique challenges of the WFIRST space environment, degradation to the sensor's charge transfer efficiency will be assessed, as a result of damage from high-energy particles such as protons, electrons, and cosmic rays. Science-grade CCD201-20 EMCCDs have been irradiated to a proton fluence that reflects the projected WFIRST orbit. Performance degradation due to radiation displacement damage is reported, which is the first such study for a CCD201-20 that replicates the WFIRST conditions. In addition, techniques intended to identify and mitigate radiation-induced electron trapping, such as trap pumping, custom clocking, and thermal cycling, are discussed.

The X-Ray Surveyor Mission: A Concept Study

Abstract: NASA's Chandra X-ray Observatory continues to provide an unparalleled means for exploring the high-energy universe. With its half-arcsecond angular resolution, Chandra studies have deepened our understanding of galaxy clusters, active galactic nuclei, galaxies, supernova remnants, neutron stars, black holes, and solar system objects. As we look beyond Chandra, it is clear that comparable or even better angular resolution with greatly increased photon throughput is essential to address ever more demanding science questions—such as the formation and growth of black hole seeds at very high redshifts; the emergence of the first galaxy groups; and details of feedback over a large range of scales from galaxies to galaxy clusters. Recently, we initiated a concept study for such a mission, dubbed X-ray Surveyor. The X-ray Surveyor strawman payload is comprised of a high-resolution mirror assembly and an instrument set, which may include an X-ray microcalorimeter, a high-definition imager, and a dispersive grating spectrometer and its readout. The mirror assembly will consist of highly nested, thin, grazing-incidence mirrors, for which a number of technical approaches are currently under development—including adjustable X-ray optics, differential deposition, and new polishing techniques applied to a variety of substrates. This study benefits from previous studies of large missions carried out over the past two decades and, in most areas, points to mission requirements no more stringent than those of Chandra.