James W. Tschanz

Bio: James W. Tschanz is an academic researcher from Intel. The author has contributed to research in topics: CMOS & Voltage regulator. The author has an hindex of 37, co-authored 200 publications receiving 8395 citations. Previous affiliations of James W. Tschanz include Walsh University & University of Illinois at Urbana–Champaign.

Parameter variations and impact on circuits and microarchitecture

Abstract: Parameter variation in scaled technologies beyond 90nm will pose a major challenge for design of future high performance microprocessors. In this paper, we discuss process, voltage and temperature variations; and their impact on circuit and microarchitecture. Possible solutions to reduce the impact of parameter variations and to achieve higher frequency bins are also presented.

Adaptive body bias for reducing impacts of die-to-die and within-die parameter variations on microprocessor frequency and leakage

Abstract: Bidirectional adaptive body bias (ABB) is used to compensate for die-to-die parameter variations by applying an optimum pMOS and nMOS body bias voltage to each die which maximizes the die frequency subject to a power constraint. Measurements on a 150 nm CMOS test chip which incorporates on-chip ABB, show that ABB reduces variation in die frequency by a factor of seven, while improving the die acceptance rate. An enhancement of this technique, that compensates for within-die parameter variations as well, increases the number of dies accepted in the highest frequency bin. ABB is therefore shown to provide bin split improvement in the presence of increasing process parameter variations.

Die-to-Die and Within-Die Parameter Variations on Microprocessor Frequency and Leakage

Abstract: Measurements on a 150 nm CMOS test chip show that on-chip bidirectional adaptive body biasing compensates effectively for die-to-die parameter variation to meet both frequency and leakage requirements. An enhancement of this technique to correct for within-die variations triples the accepted die count in the highest frequency bin.

An 80-Tile Sub-100-W TeraFLOPS Processor in 65-nm CMOS

Abstract: This paper describes an integrated network-on-chip architecture containing 80 tiles arranged as an 8x10 2-D array of floating-point cores and packet-switched routers, both designed to operate at 4 GHz. Each tile has two pipelined single-precision floating-point multiply accumulators (FPMAC) which feature a single-cycle accumulation loop for high throughput. The on-chip 2-D mesh network provides a bisection bandwidth of 2 Terabits/s. The 15-FO4 design employs mesochronous clocking, fine-grained clock gating, dynamic sleep transistors, and body-bias techniques. In a 65-nm eight-metal CMOS process, the 275 mm2 custom design contains 100 M transistors. The fully functional first silicon achieves over 1.0 TFLOPS of performance on a range of benchmarks while dissipating 97 W at 4.27 GHz and 1.07 V supply.

Dynamic-sleep transistor and body bias for active leakage power control of microprocessors

Abstract: In order to manage the active power consumption of high-performance digital designs, active leakage control techniques are required to provide significant leakage power savings coupled with fast time constants for entering and exiting idle mode. In this paper, dynamic sleep transistors and body bias are used in conjunction with clock gating to control active leakage for a 32-bit integer execution core in 130-nm CMOS technology. Measurements on pMOS sleep transistor reveal that lowest-leakage state is reached in less than 1 /spl mu/s, resulting in 37/spl times/ reduction in leakage power, while reactivation of block is achieved in less than two clock cycles. PMOS body bias reduces leakage power by 2/spl times/ with no performance penalty, and similar reactivation time. Power measurements at 4 GHz, 1.3 V, 75/spl deg/C demonstrate 8% total power reduction using dynamic body bias and 15% power reduction using a pMOS sleep transistor, for a typical activity profile.

McPAT: an integrated power, area, and timing modeling framework for multicore and manycore architectures

Abstract: This paper introduces McPAT, an integrated power, area, and timing modeling framework that supports comprehensive design space exploration for multicore and manycore processor configurations ranging from 90nm to 22nm and beyond. At the microarchitectural level, McPAT includes models for the fundamental components of a chip multiprocessor, including in-order and out-of-order processor cores, networks-on-chip, shared caches, integrated memory controllers, and multiple-domain clocking. At the circuit and technology levels, McPAT supports critical-path timing modeling, area modeling, and dynamic, short-circuit, and leakage power modeling for each of the device types forecast in the ITRS roadmap including bulk CMOS, SOI, and double-gate transistors. McPAT has a flexible XML interface to facilitate its use with many performance simulators. Combined with a performance simulator, McPAT enables architects to consistently quantify the cost of new ideas and assess tradeoffs of different architectures using new metrics like energy-delay-area2 product (EDA2P) and energy-delay-area product (EDAP). This paper explores the interconnect options of future manycore processors by varying the degree of clustering over generations of process technologies. Clustering will bring interesting tradeoffs between area and performance because the interconnects needed to group cores into clusters incur area overhead, but many applications can make good use of them due to synergies of cache sharing. Combining power, area, and timing results of McPAT with performance simulation of PARSEC benchmarks at the 22nm technology node for both common in-order and out-of-order manycore designs shows that when die cost is not taken into account clustering 8 cores together gives the best energy-delay product, whereas when cost is taken into account configuring clusters with 4 cores gives the best EDA2P and EDAP.

Device Requirements for Optical Interconnects to Silicon Chips

Abstract: We examine the current performance and future demands of interconnects to and on silicon chips. We compare electrical and optical interconnects and project the requirements for optoelectronic and optical devices if optics is to solve the major problems of interconnects for future high-performance silicon chips. Optics has potential benefits in interconnect density, energy, and timing. The necessity of low interconnect energy imposes low limits especially on the energy of the optical output devices, with a ~ 10 fJ/bit device energy target emerging. Some optical modulators and radical laser approaches may meet this requirement. Low (e.g., a few femtofarads or less) photodetector capacitance is important. Very compact wavelength splitters are essential for connecting the information to fibers. Dense waveguides are necessary on-chip or on boards for guided wave optical approaches, especially if very high clock rates or dense wavelength-division multiplexing (WDM) is to be avoided. Free-space optics potentially can handle the necessary bandwidths even without fast clocks or WDM. With such technology, however, optics may enable the continued scaling of interconnect capacity required by future chips.

Parameter variations and impact on circuits and microarchitecture

Abstract: Parameter variation in scaled technologies beyond 90nm will pose a major challenge for design of future high performance microprocessors. In this paper, we discuss process, voltage and temperature variations; and their impact on circuit and microarchitecture. Possible solutions to reduce the impact of parameter variations and to achieve higher frequency bins are also presented.

Designing reliable systems from unreliable components: the challenges of transistor variability and degradation

Abstract: As technology scales, variability in transistor performance continues to increase, making transistors less and less reliable. This creates several challenges in building reliable systems, from the unpredictability of delay to increasing leakage current. Finding solutions to these challenges require a concerted effort on the part of all the players in a system design. This article discusses these effects and proposes microarchitecture, circuit, and testing research that focuses on designing with many unreliable components (transistors) to yield reliable system designs.

Thousand core chips: a technology perspective

Abstract: This paper presents the many-core architecture, with hundreds to thousands of small cores, to deliver unprecedented compute performance in an affordable power envelope. We discuss fine grain power management, memory bandwidth, on die networks, and system resiliency for the many-core system.