Jin Wang

Bio: Jin Wang is an academic researcher from Tianjin University. The author has contributed to research in topics: Specific surface area & Carbonization. The author has an hindex of 8, co-authored 15 publications receiving 645 citations.

Electrochemical Performances of Nanoparticle Fe3O4/Activated Carbon Supercapacitor Using KOH Electrolyte Solution

Abstract: In this study, activated carbon (AC)-Fe3O4 nanoparticles asymmetric supercapacitor cells have been assembled and characterized in 6 M KOH aqueous electrolyte for the first time. The nanostructure Fe3O4 was prepared by the microwave method. It only cost several minutes to prepare magnetite nanoparticles with average particle size of 35 nm. The electrochemical performances of the hybrid AC-Fe3O4 supercapacitor were tested by cyclic voltammetry, electrochemical impedance spectroscopy, and galvanostatic charge−discharge tests. The results show that the asymmetric supercapacitor has electrochemical capacitance performance within potential range 0−1.2 V. The supercapacitor delivered a specific capacitance of 37.9 F/g at a current density of 0.5 mA/cm2. The result of cyclic characteristic test showed that it also can keep 82% of initial capacity over 500 cycles.

Fast parallel algorithms for short-range molecular dynamics

Abstract: Three parallel algorithms for classical molecular dynamics are presented. The first assigns each processor a fixed subset of atoms; the second assigns each a fixed subset of inter-atomic forces to compute; the third assigns each a fixed spatial region. The algorithms are suitable for molecular dynamics models which can be difficult to parallelize efficiently—those with short-range forces where the neighbors of each atom change rapidly. They can be implemented on any distributed-memory parallel machine which allows for message-passing of data between independently executing processors. The algorithms are tested on a standard Lennard-Jones benchmark problem for system sizes ranging from 500 to 100,000,000 atoms on several parallel supercomputers--the nCUBE 2, Intel iPSC/860 and Paragon, and Cray T3D. Comparing the results to the fastest reported vectorized Cray Y-MP and C90 algorithm shows that the current generation of parallel machines is competitive with conventional vector supercomputers even for small problems. For large problems, the spatial algorithm achieves parallel efficiencies of 90% and a 1840-node Intel Paragon performs up to 165 faster than a single Cray C9O processor. Trade-offs between the three algorithms and guidelines for adapting them to more complex molecular dynamics simulations are also discussed.

Ultracapacitors: Why, How, and Where is the Technology

Abstract: The science and technology of ultracapacitors are reviewed for a number of electrode materials, including carbon, mixed metal oxides, and conducting polymers. More work has been done using microporous carbons than with the other materials and most of the commercially available devices use carbon electrodes and an organic electrolytes. The energy density of these devices is 3¯5 Wh/kg with a power density of 300¯500 W/kg for high efficiency (90¯95%) charge/discharges. Projections of future developments using carbon indicate that energy densities of 10 Wh/kg or higher are likely with power densities of 1¯2 kW/kg. A key problem in the fabrication of these advanced devices is the bonding of the thin electrodes to a current collector such the contact resistance is less than 0.1 cm2. Special attention is given in the paper to comparing the power density characteristics of ultracapacitors and batteries. The comparisons should be made at the same charge/discharge efficiency.

KOH activation of carbon-based materials for energy storage

Abstract: Because of their availability, adjustable microstructure, varieties of forms, and large specific surface area, porous carbon materials are of increasing interest for use in hydrogen storage adsorbents and electrode materials in supercapacitors and lithium–sulfur cells from the viewpoint of social sustainability and environmental friendliness. Therefore, much effort has been made to synthesize and tailor the microstructures of porous carbon materials via various activation procedures (physical and chemical activation). In particular, the chemical activation of various carbon sources using KOH as the activating reagent is very promising because of its lower activation temperature and higher yields, and well-defined micropore size distribution and ultrahigh specific surface area up to 3000 m2 g−1 of the resulting porous carbons. In this feature article, we will cover recent research progress since 2007 on the synthesis of KOH-activated carbons for hydrogen and electrical energy storage (supercapacitors and lithium–sulfur batteries). The textural properties and surface chemistry of KOH-activated carbons depend on not only the synthesis parameters, but also different carbon sources employed including fossil/biomass-derived materials, synthetic organic polymers, and various nanostructured carbons (e.g. carbon nanotubes, carbon nanofibers, carbon aerogels, carbide-derived carbons, graphene, etc.). Following the introduction to KOH activation mechanisms and processing technologies, the characteristics and performance of KOH-activated carbons as well as their relationships are summarized and discussed through the extensive analysis of the literature based on different energy storage systems.

Supercapacitor electrode materials: nanostructures from 0 to 3 dimensions

Abstract: Supercapacitors have drawn considerable attention in recent years due to their high specific power, long cycle life, and ability to bridge the power/energy gap between conventional capacitors and batteries/fuel cells. Nanostructured electrode materials have demonstrated superior electrochemical properties in producing high-performance supercapacitors. In this review article, we describe the recent progress and advances in designing nanostructured supercapacitor electrode materials based on various dimensions ranging from zero to three. We highlight the effect of nanostructures on the properties of supercapacitors including specific capacitance, rate capability and cycle stability, which may serve as a guideline for the next generation of supercapacitor electrode design.

Recent Advances in Design and Fabrication of Electrochemical Supercapacitors with High Energy Densities

Abstract: In recent years, tremendous research effort has been aimed at increasing the energy density of supercapacitors without sacrificing high power capability so that they reach the levels achieved in batteries and at lowering fabrication costs For this purpose, two important problems have to be solved: first, it is critical to develop ways to design high performance electrode materials for supercapacitors; second, it is necessary to achieve controllably assembled supercapacitor types (such as symmetric capacitors including double-layer and pseudo-capacitors, asymmetric capacitors, and Li-ion capacitors) The explosive growth of research in this field makes this review timely Recent progress in the research and development of high performance electrode materials and high-energy supercapacitors is summarized Several key issues for improving the energy densities of supercapacitors and some mutual relationships among various effecting parameters are reviewed, and challenges and perspectives in this exciting field are also discussed This provides fundamental insight into supercapacitors and offers an important guideline for future design of advanced next-generation supercapacitors for industrial and consumer applications