scispace - formally typeset
Search or ask a question
Author

Jinlin Wang

Bio: Jinlin Wang is an academic researcher from Intel. The author has contributed to research in topics: Thermal conductivity & Viscosity. The author has an hindex of 10, co-authored 28 publications receiving 1120 citations.

Papers
More filters
Journal ArticleDOI
TL;DR: Experimental results on the viscosity of alumina-based nanofluids are reported for various shear rates, temperature, nanoparticle diameter, and nanoparticle volume fraction.
Abstract: Experimental results on the viscosity of alumina-based nanofluids are reported for various shear rates, temperature, nanoparticle diameter, and nanoparticle volume fraction. From the data it seems that the increase in the nanofluid viscosity is higher than the enhancement in the thermal conductivity as reported in the literature. It is shown, however, that the viscosity has to be increased by more than a factor of 4—relative to the increase in thermal conductivity—to make the nanofluid thermal performance worse than that of the base fluid.

735 citations

Journal ArticleDOI
Ravi Prasher1, Jim Shipley1, Suzana Prstic1, Paul Koning1, Jinlin Wang1 
TL;DR: In this article, a rheology-based semi-empirical model for the prediction of the bond line thickness (BLT) of particle laden polymers is presented.
Abstract: Particle laden polymers are one of the most prominent thermal interface materials (TIM) used in electronics cooling. Most of the research has primarily dealt with the understanding of the thermal conductivity of these types of TIMs. For thermal design, reduction of the thermal resistance is the end goal. Thermal resistance is not only dependent on the thermal conductivity, but also on the bond line thickness (BLT) of these TIMs. It is not clear which material property(s) of these particle laden TIMs affects the BLT and eventually the thermal resistance. This paper introduces a rheology based semiempirical model for the prediction of the BLT of these TIMs. BLT depends on the yield stress of the particle laden polymer and the applied pressure. The BLT model combined with the thermal conductivity model can he used for modeling the thermal resistance of these TIMs for factors such as particle volume faction, particle shape, base polymer viscosity, etc.

130 citations

Patent
04 Jan 2002
TL;DR: In this paper, an electronic package includes a heat-generating electronic component such as an integrated circuit chip, a thermally conductive member, which may be an integrated heat spreader, and a low modulus thermal interface material in heat conducting relation between the electronic component and the thermally conducting member.
Abstract: An electronic package includes a heat-generating electronic component such as an integrated circuit chip, a thermally conductive member, which may be an integrated heat spreader, and a low modulus thermal interface material in heat conducting relation between the electronic component and the thermally conductive member. Increased thermal performance requirements at the electronic component level are met by the thermal interface material, which includes a polymer matrix and thermally conductive filler, which has a storage shear modulus (G′) at 125° C. of less than about 100 kPa, and which has a gel point, as indicated by a value of G′/G″ of ≧1, where G″ is the loss shear modulus of the thermal interface material. The values for G′ and G″ are measured by a strain-controlled rheometer.

71 citations

Journal ArticleDOI
Jinlin Wang1
TL;DR: Experimental methods were developed to measure the surface tension and the contact angle of underfills at temperatures over 100 °C and showed that the contact angles for underfill on a substrate was time dependent, and the interaction between underfill and substrate affects not only gap filling, but also filleting.

50 citations

Journal ArticleDOI
Jinlin Wang1
TL;DR: How the rheological properties can affect underfill filler settling and flow voids is discussed and it was shown that the underfills with small fillers have shear-thickening viscosity and yield stress.

40 citations


Cited by
More filters
Journal ArticleDOI
TL;DR: In this article, the authors considered seven slip mechanisms that can produce a relative velocity between the nanoparticles and the base fluid and concluded that only Brownian diffusion and thermophoresis are important slip mechanisms in nanofluids.
Abstract: Nanofluids are engineered colloids made of a base fluid and nanoparticles (1-100 nm) Nanofluids have higher thermal conductivity' and single-phase heat transfer coefficients than their base fluids In particular the heat transfer coefficient increases appear to go beyond the mere thermal-conductivity effect, and cannot be predicted by traditional pure-fluid correlations such as Dittus-Boelter's In the nanofluid literature this behavior is generally attributed to thermal dispersion and intensified turbulence, brought about by nanoparticle motion To test the validity of this assumption, we have considered seven slip mechanisms that can produce a relative velocity between the nanoparticles and the base fluid These are inertia, Brownian diffusion, thermophoresis, diffusioplwresis, Magnus effect, fluid drainage, and gravity We concluded that, of these seven, only Brownian diffusion and thermophoresis are important slip mechanisms in nanofluids Based on this finding, we developed a two-component four-equation nonhomogeneous equilibrium model for mass, momentum, and heat transport in nanofluids A nondimensional analysis of the equations suggests that energy transfer by nanoparticle dispersion is negligible, and thus cannot explain the abnormal heat transfer coefficient increases Furthermore, a comparison of the nanoparticle and turbulent eddy time and length scales clearly indicates that the nanoparticles move homogeneously with the fluid in the presence of turbulent eddies so an effect on turbulence intensity is also doubtful Thus, we propose an alternative explanation for the abnormal heat transfer coefficient increases: the nanofluid properties may vary significantly within the boundary layer because of the effect of the temperature gradient and thermophoresis For a heated fluid, these effects can result in a significant decrease of viscosity within the boundary layer, thus leading to heat transfer enhancement A correlation structure that captures these effects is proposed

5,329 citations

Book
01 Jan 1971
TL;DR: In this paper, Ozaki et al. describe the dynamics of adsorption and Oxidation of organic Molecules on Illuminated Titanium Dioxide Particles Immersed in Water.
Abstract: 1: Magnetic Particles: Preparation, Properties and Applications: M. Ozaki. 2: Maghemite (gamma-Fe2O3): A Versatile Magnetic Colloidal Material C.J. Serna, M.P. Morales. 3: Dynamics of Adsorption and Oxidation of Organic Molecules on Illuminated Titanium Dioxide Particles Immersed in Water M.A. Blesa, R.J. Candal, S.A. Bilmes. 4: Colloidal Aggregation in Two-Dimensions A. Moncho-Jorda, F. Martinez-Lopez, M.A. Cabrerizo-Vilchez, R. Hidalgo Alvarez, M. Quesada-PMerez. 5: Kinetics of Particle and Protein Adsorption Z. Adamczyk.

1,870 citations

Journal ArticleDOI
TL;DR: In this article, two empirical correlations for predicting the effective thermal conductivity and dynamic viscosity of nanofluids, based on a high number of experimental data available in the literature, are proposed and discussed.

971 citations

Journal ArticleDOI
TL;DR: In this article, the stability of nanofluids is discussed as it has a major role in heat transfer enhancement for further possible applications, and general stabilization methods as well as various types of instruments for stability inspection.

948 citations

Journal ArticleDOI
25 Sep 2006
TL;DR: The focus is on the rheology-based modeling and design of polymeric TIMs due to their widespread use and merits and demerits of using nanoparticles and nanotubes for TIM applications.
Abstract: With the continual increase in cooling demand for microprocessors, there has been an increased focus within the microelectronics industry on developing thermal solutions. Thermal interface materials (TIMs) play a key role in thermally connecting various components of the thermal solution. Review of the progress made in the area of TIMs in the past five years is presented. The focus is on the rheology-based modeling and design of polymeric TIMs due to their widespread use. Review of limited literature on the thermal performance of solders is also provided. Merits and demerits of using nanoparticles and nanotubes for TIM applications are also discussed. I conclude the paper with some directions for the future that I feel are relatively untouched and potentially very beneficial

785 citations