Showing papers by "Jong Hyun Ahn published in 2020"

Full-color active-matrix organic light-emitting diode display on human skin based on a large-area MoS2 backplane.

Abstract: Electronic applications are continuously developing and taking new forms. Foldable, rollable, and wearable displays are applicable for human health care monitoring or robotics, and their operation relies on organic light-emitting diodes (OLEDs). Yet, the development of semiconducting materials with high mechanical flexibility has remained a challenge and restricted their use in unusual format electronics. This study presents a wearable full-color OLED display using a two-dimensional (2D) material-based backplane transistor. The 18-by-18 thin-film transistor array was fabricated on a thin MoS2 film that was transferred to Al2O3 (30 nm)/polyethylene terephthalate (6 μm). Red, green, and blue OLED pixels were deposited on the device surface. This 2D material offered excellent mechanical and electrical properties and proved to be capable of driving circuits for the control of OLED pixels. The ultrathin device substrate allowed for integration of the display on an unusual substrate, namely, a human hand.

A 6.5- μ W 10-kHz BW 80.4-dB SNDR G m -C-Based CT ∆∑ Modulator With a Feedback-Assisted G m Linearization for Artifact-Tolerant Neural Recording

Abstract: This article presents a Gm-C-based continuous-time delta–sigma modulator (CTDSM) for artifact-tolerant neural recording interfaces. We propose the feedback-assisted Gm linearization technique, which is applied to the first Gm-C integrator by using a resistive feedback digital-to-analog converter (DAC) in parallel to the degeneration resistor of the input Gm. This enables the input Gm to process the quantization noise, thereby improving the input range and linearity of the Gm-C-based CTDSM, significantly. An energy-efficient second-order loop filter is realized by using a voltage-controlled oscillator (VCO) as the second integrator and a phase quantizer. A proportional–integral (PI) transfer function is employed at the first integrator, which minimizes the output swing while maintaining loop stability. Fabricated in a 110-nm CMOS process, the prototype CTDSM achieves a high input impedance, 300-mVpp linear input range, 80.4-dB signal-to-noise and distortion ratio (SNDR), 81-dB dynamic range (DR), and 76-dB common-mode rejection ratio (CMRR) and consumes only 6.5 $\mu \text{W}$ with a signal bandwidth of 10 kHz. This corresponds to a figure of merit (FoM) of 172.3 dB, which is the state of the art among the neural recording ADCs. This work is also validated through the in vivo experiment.

Biomimetic Tactile Sensors Based on Nanomaterials.

Abstract: Tactile sensor technology has been researched extensively in response to the increasing demand for robotic and wearable healthcare systems. Studies on tactile sensory systems have primarily focused on achieving two goals: (1) developing technologies with high sensing abilities that mimic the biological functions and characteristics of the sensory systems of human skin and (2) satisfying the requirements of wearable device applications by fabricating mechanically flexible devices with low-power data analysis and processing abilities. In this Perspective, we present recent advances in artificial tactile sensory systems, which are based on biomimetic technologies that exhibit functional features of biological systems including mechanoreceptors and human skin sensory neurons for human-machine interfaces. We also discuss the opportunities, current challenges, potential solutions, and future investigative directions pertaining to this field.

Assembly of Foldable 3D Microstructures Using Graphene Hinges.

Abstract: Origami/kirigami-inspired 3D assembly approaches have recently attracted attention for a variety of applications, such as advanced optoelectronic devices and biomedical sensors. The results reported here describe an approach to construct classes of multiple foldable 3D microstructures that involve deformations that typical conductive materials, such as conventional metal films, cannot tolerate. Atomically thin graphene sheets serve as folding hinges during a process of 2D to 3D conversion via a deterministic buckling process. The exceptional mechanical properties of graphene enable the controlled, geometric transformation of a 2D precursor bonded at selective sites on a prestretched elastomer into folded 3D microstructures, in a reversible manner without adverse effects on the electrical properties. Experimental and computational investigations of the folding mechanisms for such types of 3D objects reveal the underlying physics and the dependence of the process on the thickness of the graphene/supporting films that define the hinges.

Breaking the absorption limit of Si toward SWIR wavelength range via strain engineering.

Abstract: Silicon has been widely used in the microelectronics industry. However, its photonic applications are restricted to visible and partial near-infrared spectral range owing to its fundamental optical bandgap (1.12 eV). With recent advances in strain engineering, material properties, including optical bandgap, can be tailored considerably. This paper reports the strain-induced shrinkage in the Si bandgap, providing photosensing well beyond its fundamental absorption limit in Si nanomembrane (NM) photodetectors (PDs). The Si-NM PD pixels were mechanically stretched (biaxially) by a maximum strain of ~3.5% through pneumatic pressure-induced bulging, enhancing photoresponsivity and extending the Si absorption limit up to 1550 nm, which is the essential wavelength range of the lidar sensors for obstacle detection in self-driving vehicles. The development of deformable three-dimensional optoelectronics via gas pressure-induced bulging also facilitated the realization of unique device designs with concave and convex hemispherical architectures, which mimics the electronic prototypes of biological eyes.

Biodegradable and bioabsorbable sensors based on two-dimensional materials

Abstract: Two-dimensional (2D) materials, including graphene and transition metal dichalcogenides (TMDCs), have attracted considerable attention for the last decade due to their unique electrical, optical and mechanical properties. Recently, as their unique characteristics of biocompatibility and biodegradation are known, research on applying them in diagnostic and therapeutic applications has received considerable attention. This review provides a broad overview of recent reports on the biocompatibility and biodegradability of 2D materials and highlights recent progress in biodegradable and bioabsorbable sensors for diagnostic and therapeutic applications.

Epitaxial Growth of Wafer-Scale Molybdenum Disulfide/Graphene Heterostructures by Metal-Organic Vapor-Phase Epitaxy and Their Application in Photodetectors

Abstract: Van der Waals heterostructures have attracted increasing interest, owing to the combined benefits of their constituents. These hybrid nanostructures can be realized via epitaxial growth, which offers a promising approach for the controlled synthesis of the desired crystal phase and the interface between van der Waals layers. Here, the epitaxial growth of a continuous molybdenum disulfide (MoS2) film on large-area graphene, which was directly grown on a sapphire substrate, is reported. Interestingly, the grain size of MoS2 grown on graphene increases, whereas that of MoS2 grown on SiO2 decreases with an increasing amount of hydrogen in the chemical vapor deposition reactor. In addition, to achieve the same quality, MoS2 grown on graphene requires a much lower growth temperature (400 °C) than that grown on SiO2 (580 °C). The MoS2/graphene heterostructure that was epitaxially grown on a transparent platform was investigated to explore its photosensing properties and was found to exhibit inverse photoresponse with highly uniform photoresponsivity in the photodetector pixels fabricated across a full wafer. The MoS2/graphene heterostructure exhibited ultrahigh photoresponsivity (4.3 × 104 A W-1) upon exposure to visible light of a wide range of wavelengths, confirming the growth of a high-quality MoS2/graphene heterostructure with a clean interface.

3D motion tracking display enabled by magneto-interactive electroluminescence.

Abstract: Development of a human-interactive display enabling the simultaneous sensing, visualisation, and memorisation of a magnetic field remains a challenge. Here we report a skin-patchable magneto-interactive electroluminescent display, which is capable of sensing, visualising, and storing magnetic field information, thereby enabling 3D motion tracking. A magnetic field-dependent conductive gate is employed in an alternating current electroluminescent display, which is used to produce non-volatile and rewritable magnetic field-dependent display. By constructing mechanically flexible arrays of magneto-interactive displays, a spin-patchable and pixelated platform is realised. The magnetic field varying along the z-axis enables the 3D motion tracking (monitoring and memorisation) on 2D pixelated display. This 3D motion tracking display is successfully used as a non-destructive surgery-path guiding, wherein a pathway for a surgical robotic arm with a magnetic probe is visualised and recorded on a display patched on the abdominal skin of a rat, thereby helping the robotic arm to find an optimal pathway. Designing human-interactive displays enabling the simultaneous sensing, visualization, and memorization of a magnetic field remains a challenge. Here, the authors present a skin-patchable magneto-interactive electroluminescent display by employing a magnetic field-dependent conductive gate, thereby enabling 3D motion tracking.

Slippery and Wear-Resistant Surfaces Enabled by Interface Engineered Graphene.

Abstract: Friction and wear remain the primary cause of mechanical energy dissipation and system failure. Recent studies reveal graphene as a powerful solid lubricant to combat friction and wear. Most of these studies have focused on nanoscale tribology and have been limited to a few specific surfaces. Here, we uncover many unknown aspects of graphene's contact-sliding at micro- and macroscopic tribo-scales over a broader range of surfaces. We discover that graphene's performance reduces for surfaces with increasing roughness. To overcome this, we introduce a new type of graphene/silicon nitride (SiNx, 3 nm) bilayer overcoats that exhibit superior performance compared to native graphene sheets (mono and bilayer), that is, display the lowest microscale friction and wear on a range of tribologically poor flat surfaces. More importantly, two-layer graphene/SiNx bilayer lubricant (<4 nm in total thickness) shows the highest macroscale wear durability on tape-head (topologically variant surface) that exceeds most previous thicker (∼7-100 nm) overcoats. Detailed nanoscale characterization and atomistic simulations explain the origin of the reduced friction and wear arising from these nanoscale coatings. Overall, this study demonstrates that engineered graphene-based coatings can outperform conventional coatings in a number of technologies.

Dual Resonant Sum Frequency Generations from Two-Dimensional Materials.

Abstract: We propose dual resonant optical sum frequency generation (SFG), where the two most singular resonances could be selected, and report for the monolayer (1L-) WSe2 when one (ω1) of two excitation pu...

Transient sensor based on molybdenum disulfide and manufacturing method thereof

Abstract: Disclosed are a transient sensor using molybdenum disulfide and a manufacturing method thereof. According to an embodiment of the present invention, the transient sensor using molybdenum disulfide comprises: a water-soluble substrate; a water-soluble insulating layer deposited on the water-soluble substrate; an electrode layer formed by using any one of molybdenum and magnesium (Mg) on the water-soluble insulating layer; and a channel layer connected to the formed electrode layer and formed by using molybdenum disulfide on the water-soluble insulating layer. The transient sensor using molybdenum disulfide can be decomposed in a living matter within a critical time, when inserted into the living matter.