Jun Fan

Bio: Jun Fan is an academic researcher from Missouri University of Science and Technology. The author has contributed to research in topics: Equivalent circuit & Printed circuit board. The author has an hindex of 36, co-authored 482 publications receiving 5641 citations. Previous affiliations of Jun Fan include Ulsan National Institute of Science and Technology & University of Missouri.

Stressed jitter analysis for physical link characterization

Abstract: A link-path analysis approach is introduced in this paper based on the frequency-domain S-parameters of the link path. Different jitter components are also modelled and can be injected into the analysis to characterize the link responses to different types of jitter input. Stressed link path analysis can be very useful in practical engineering designs in terms of link path optimization, device selection and qualification, etc.

Complex power distribution network investigation using SPICE based extraction from first principle formulations

Abstract: The modeling and the analysis of the power distribution networks (PDN) within multi-layer printed circuit board is crucial for the investigation of the performance of PCB systems. Carrying out such analyses in SPICE based tools has the advantage of being faster than the corresponding full-wave modeling and it allows obtaining both frequency and time domain results.

Detection of open and short faults in 3D-ICs based on through silicon via (TSV)

Abstract: This paper proposes a procedure for estimating the location of open or short defects in a Through Silicon Via daisy-chain structure. The equivalent inductance and capacitance are extracted, at low frequency, through the measured and/or computed Z11 parameter of a three dimensional model in which the short and open defects are intentionally created in specific points.

Modeling broadside coupled traces using equivalent per unit length (Eq PUL) RLGC model

Abstract: Increases in printed circuit board (PCB) cost is leading to denser routing of high speed signal traces and this, in turn, is increasing the crosstalk among the traces. The crosstalk between the broadside coupled traces in adjacent layers is becoming an important factor to account for as the signal speeds increase. The coupling between parallel broadside coupled traces can be modeled using multi-conductor transmission line theory based on telegrapher equations using equivalent per-unit-length (Eq PUL) resistance, inductance, capacitance, and conductance (RLCG) matrices. The same approach is not applicable for the traces crossing at an arbitrary angle. A fast methodology to develop Eq PUL RLGC models that captures the coupling physics of broadside coupled traces crossing at an angle based on geometrical parameters of the stackup, and the dielectric material properties is proposed based on the idea presented in [1]. In this paper, validation of these equivalent models is done by estimating the crosstalk impact on eye opening at a specified bit error rate (BER) at different signal speeds and results are compared against full wave models.

Inductance extraction for physics-based modeling of power net area fills with complex shapes and voids using the plane-pair PEEC method

Abstract: Identifying the dominant inductance in power distribution network design for multi-layer printed circuit boards that use power net area fills is essential. The plane-Pair partial element equivalent circuit method is used herein to extract a lumped inductance suitable for a physics-based circuit model for power net area fills. The method is being applied for evaluating inductance for irregular geometry with cutouts and holes.

I and i

Abstract: There is, I think, something ethereal about i —the square root of minus one. I remember first hearing about it at school. It seemed an odd beast at that time—an intruder hovering on the edge of reality. Usually familiarity dulls this sense of the bizarre, but in the case of i it was the reverse: over the years the sense of its surreal nature intensified. It seemed that it was impossible to write mathematics that described the real world in …

IEEE Transactions on Microwave Theory and Techniques and Antennas and Propagation Announce a Joint Special Issue on Ultra-Wideband (UWB) Technology

Abstract: Before the emergence of ultra-wideband (UWB) radios, widely used wireless communications were based on sinusoidal carriers, and impulse technologies were employed only in specific applications (e.g. radar). In 2002, the Federal Communication Commission (FCC) allowed unlicensed operation between 3.1–10.6 GHz for UWB communication, using a wideband signal format with a low EIRP level (−41.3dBm/MHz). UWB communication systems then emerged as an alternative to narrowband systems and significant effort in this area has been invested at the regulatory, commercial, and research levels.