Diamond-like carbon (DLC) is a metastable form of amorphous carbon with significant sp3 bonding. DLC is a semiconductor with a high mechanical hardness, chemical inertness, and optical transparency. This review will describe the deposition methods, deposition mechanisms, characterisation methods, electronic structure, gap states, defects, doping, luminescence, field emission, mechanical properties and some applications of DLCs. The films have widespread applications as protective coatings in areas, such as magnetic storage disks, optical windows and micro-electromechanical devices (MEMs).

/pdf/diamond-like-amorphous-carbon-3pczopr0z7.pdf

Diamond-like amorphous carbon

Transparent conductors as solar energy materials: A panoramic review

Electrochromic tungsten oxide films: Review of progress 1993–1998

https://www.diva-portal.org/smash/get/diva2:17175/FULLTEXT02

Ionized physical vapor deposition (IPVD): A review of technology and applications

http://liu.diva-portal.org/smash/get/diva2:303552/FULLTEXT01

The Mn+1AXn phases: Materials science and thin-film processing

Using a novel pulsed power supply in combination with a standard circular flat magnetron source, operated with a Cu target, a peak power density of 2800 W cm -2 was achieved. This results in a very intense plasma with peak ion current densities of up to 3.4 A cm −2 at the substrate situated 10 cm from the target. The ionized fraction of the deposited Cu flux was estimated to be approximately 70% from deposition rate measurements. The potential for high-aspect-ratio trench filling applications by high power pulsed magnetron sputtering is demonstrated by deposition in via-structures. The high power pulsed technique also results in a higher degree of target utilization and an improved thickness uniformity of the deposited films compared with conventional d.c. magnetron sputtering.

A novel pulsed magnetron sputter technique utilizing very high target power densities

Time resolved plasma probe measurements of a novel high power density pulsed plasma discharge are presented. Extreme peak power densities in the pulse (on the order of several kW cm−2) result in a very dense plasma with substrate ionic flux densities of up to 1 A cm−2 at source-to-substrate distances of several cm and at a pressure of 0.13 Pa (1 mTorr). The pulse duration was ∼100 μs with a pulse repetition frequency of 50 Hz. The plasma consists of metallic and inert gas ions, as determined from time resolved Langmuir probe measurements and in situ optical emission spectroscopy data. It was found that the plasma composition at the beginning of the pulse was dominated by Ar ions. As time elapsed metal ions were detected and finally dominated the ion composition. The effect of the process parameters on the temporal development of the ionic fluxes is discussed. The ionized portion of the sputtered metal flux was found to have an average velocity of 2500 m s−1 at 6 cm distance from the source, which conforms...

Ionized sputter deposition using an extremely high plasma density pulsed magnetron discharge

Carbon nitride CNx thin films were grown by unbalanced dc magnetron sputtering from a graphite target in a pure N2 discharge, and with the substrate temperature Ts kept between 100 and 550 °C. A solenoid coil positioned in the vicinity of the substrate was used to support the magnetic field of the magnetron, so that the plasma could be increased near the substrate. By varying the coil current and gas pressure, the energy distribution and fluxes of N2+ ions and C neutrals could be varied independently of each other over a wide range. An array of Langmuir probes in the substrate position was used to monitor the radial ion flux distribution over the 75-mm-diam substrate, while the flux and energy distribution of neutrals was estimated through Monte Carlo simulations. The structure, surface roughness, and mechanical response of the films are found to be strongly dependent on the substrate temperature, and the fluxes and energies of the deposited particles. By controlling the process parameters, the film struc...

Influence of plasma parameters on the growth and properties of magnetron sputtered CNx thin films

We describe the hydrogen uptake during the synthesis of alumina films from H2O present in the high vacuum gas background. The hydrogen concentration in the films was determined by the 1H(15N,αγ)12C nuclear resonance reaction. Furthermore, we show the presence of hydrogen ions in the plasma stream by time-of-flight mass spectrometry. The hydrogen content increased in both the film and the plasma stream, as the oxygen partial pressure was increased. On the basis of these measurements and thermodynamic considerations, we suggest that an aluminum oxide hydroxide compound is formed, both on the cathode surface as well as in the film. The large scatter in the data reported in the literature for refractive index and chemical stability of alumina thin films can be explained on the basis of the suggested aluminum oxide hydroxide formation.

Karol Macak

Papers

A novel pulsed magnetron sputter technique utilizing very high target power densities

Ionized sputter deposition using an extremely high plasma density pulsed magnetron discharge

Influence of plasma parameters on the growth and properties of magnetron sputtered CNx thin films

Hydrogen uptake in alumina thin films synthesized from an aluminum plasma stream in an oxygen ambient

High rate reactive dc magnetron sputter deposition of Al 2 O 3 films