Katarina Forsgren

Bio: Katarina Forsgren is an academic researcher from Uppsala University. The author has contributed to research in topics: Thin film & Atomic layer deposition. The author has an hindex of 7, co-authored 10 publications receiving 348 citations. Previous affiliations of Katarina Forsgren include University of Tartu.

Dielectric Properties of Zirconium Oxide Grown by Atomic Layer Deposition from Iodide Precursor

Abstract: Dielectric properties of zirconium oxide grown by atomic layer deposition from iodide precursors

Deposition of HfO2 thin films in HfI4-based processes

Abstract: Due to the constantly decreasing dimensions of electronic devices, the conventional dielectric material in transistors and capacitors, SiO2, has to be replaced by a material with higher dielectric constant. Some of the most promising candidates are tantalum oxide,Ta2O5, zirconium oxide, ZrO2 and hafnium oxide, HfO2.This thesis describes new chemical vapour deposition (CVD) and atomic layer deposition (ALD) processes for deposition of Ta2O5, ZrO2 and HfO2 using the metal iodides as starting materials. The layer-by-layer growth in ALD was also studied in real time with a quartz crystal microbalance (QCM) to examine the process characteristics and to find suitable parameters for film deposition.All the processes presented here produced high-purity films at low deposition temperatures. It was also found that films deposited on Pt substrates generally crystallise at lower temperature, or with lower thickness, than on silicon and single-crystalline oxide substrates. Films grown on MgO(001) and α-Al2O3(001) substrates were strongly textured or epitaxial. For example, monoclinic HfO2 deposited on MgO(001) were epitaxial for deposition temperatures of 400-500 C in ALD and 500-600 C in CVD. Electrical characterisation showed that the crystallinity of the films had a strong effect on the dielectric constant, except in cases of very thin films, where the dielectric constant was more dependent on layer thickness.

Atomic Layer Deposition of Tantalum Oxide Thin Films from Iodide Precursor

Abstract: Atomic layer deposition (ALD) of Ta2O5 films from evaporated TaI5 and H2O−H2O2 was investigated in the temperature range of 240−400 °C. It was shown that TaI5 as a novel ALD precursor is sufficiently stable for deposition of amorphous or polycrystalline films. According to XPS, the films were free from iodine residues. The refractive index of the films reached 2.24. The film formation mechanism depended on the substrate temperature. The growth rate decreased linearly with substrate temperature. Real time monitoring of the growth process with a quartz crystal microbalance revealed the self-limiting nature of reactions between the film surface and precursors at substrate temperatures up to 325 °C. Etching of Ta2O5 in the TaI5 flow was observed at around 350 °C and higher temperatures. At 350 °C, the crystal growth was also initiated.

Surface chemistry of atomic layer deposition: A case study for the trimethylaluminum/water process

Abstract: Atomic layer deposition(ALD), a chemical vapor deposition technique based on sequential self-terminating gas–solid reactions, has for about four decades been applied for manufacturing conformal inorganic material layers with thickness down to the nanometer range. Despite the numerous successful applications of material growth by ALD, many physicochemical processes that control ALD growth are not yet sufficiently understood. To increase understanding of ALD processes, overviews are needed not only of the existing ALD processes and their applications, but also of the knowledge of the surface chemistry of specific ALD processes. This work aims to start the overviews on specific ALD processes by reviewing the experimental information available on the surface chemistry of the trimethylaluminum/water process. This process is generally known as a rather ideal ALD process, and plenty of information is available on its surface chemistry. This in-depth summary of the surface chemistry of one representative ALD process aims also to provide a view on the current status of understanding the surface chemistry of ALD, in general. The review starts by describing the basic characteristics of ALD, discussing the history of ALD—including the question who made the first ALD experiments—and giving an overview of the two-reactant ALD processes investigated to date. Second, the basic concepts related to the surface chemistry of ALD are described from a generic viewpoint applicable to all ALD processes based on compound reactants. This description includes physicochemical requirements for self-terminating reactions,reaction kinetics, typical chemisorption mechanisms, factors causing saturation, reasons for growth of less than a monolayer per cycle, effect of the temperature and number of cycles on the growth per cycle (GPC), and the growth mode. A comparison is made of three models available for estimating the sterically allowed value of GPC in ALD. Third, the experimental information on the surface chemistry in the trimethylaluminum/water ALD process are reviewed using the concepts developed in the second part of this review. The results are reviewed critically, with an aim to combine the information obtained in different types of investigations, such as growth experiments on flat substrates and reaction chemistry investigation on high-surface-area materials. Although the surface chemistry of the trimethylaluminum/water ALD process is rather well understood, systematic investigations of the reaction kinetics and the growth mode on different substrates are still missing. The last part of the review is devoted to discussing issues which may hamper surface chemistry investigations of ALD, such as problematic historical assumptions, nonstandard terminology, and the effect of experimental conditions on the surface chemistry of ALD. I hope that this review can help the newcomer get acquainted with the exciting and challenging field of surface chemistry of ALD and can serve as a useful guide for the specialist towards the fifth decade of ALD research.

Crystallinity of inorganic films grown by atomic layer deposition: Overview and general trends

Abstract: Atomic layer deposition (ALD) is gaining attention as a thin film deposition method, uniquely suitable for depositing uniform and conformal films on complex three-dimensional topographies. The deposition of a film of a given material by ALD relies on the successive, separated, and self-terminating gas–solid reactions of typically two gaseous reactants. Hundreds of ALD chemistries have been found for depositing a variety of materials during the past decades, mostly for inorganic materials but lately also for organic and inorganic–organic hybrid compounds. One factor that often dictates the properties of ALD films in actual applications is the crystallinity of the grown film: Is the material amorphous or, if it is crystalline, which phase(s) is (are) present. In this thematic review, we first describe the basics of ALD, summarize the two-reactant ALD processes to grow inorganic materials developed to-date, updating the information of an earlier review on ALD [R. L. Puurunen, J. Appl. Phys. 97, 121301 (2005)], and give an overview of the status of processing ternary compounds by ALD. We then proceed to analyze the published experimental data for information on the crystallinity and phase of inorganic materials deposited by ALD from different reactants at different temperatures. The data are collected for films in their as-deposited state and tabulated for easy reference. Case studies are presented to illustrate the effect of different process parameters on crystallinity for representative materials: aluminium oxide, zirconium oxide, zinc oxide, titanium nitride, zinc zulfide, and ruthenium. Finally, we discuss the general trends in the development of film crystallinity as function of ALD process parameters. The authors hope that this review will help newcomers to ALD to familiarize themselves with the complex world of crystalline ALD films and, at the same time, serve for the expert as a handbook-type reference source on ALD processes and film crystallinity.

Atomic Layer Deposition of Hafnium and Zirconium Oxides Using Metal Amide Precursors

Abstract: Atomic layer deposition (ALD) of smooth and highly conformal films of hafnium and zirconium oxides was studied using six metal alkylamide precursors for hafnium and zirconium. Water was used as an oxygen source during these experiments. As deposited, these films exhibited a smooth surface with a measured roughness equivalent to that of the substrate on which they were deposited. These films also exhibited a very high degree of conformality: 100% step coverage on holes with aspect ratios greater than 35. The films were completely uniform in thickness and composition over the length of the deposition reactor. The films were free of detectable impurities and had the expected (2:1) oxygen-to-metal ratio. Films were deposited at substrate temperatures from 50 to 500 °C from precursors that were vaporized at temperatures from 40 to 140 °C. The precursors were found to be highly reactive with hydroxylated surfaces. Their vapor pressures were measured over a wide temperature range. Deposition reactor design and ...

High- k Gate Dielectrics for Emerging Flexible and Stretchable Electronics

Abstract: Recent advances in flexible and stretchable electronics (FSE), a technology diverging from the conventional rigid silicon technology, have stimulated fundamental scientific and technological research efforts. FSE aims at enabling disruptive applications such as flexible displays, wearable sensors, printed RFID tags on packaging, electronics on skin/organs, and Internet-of-things as well as possibly reducing the cost of electronic device fabrication. Thus, the key materials components of electronics, the semiconductor, the dielectric, and the conductor as well as the passive (substrate, planarization, passivation, and encapsulation layers) must exhibit electrical performance and mechanical properties compatible with FSE components and products. In this review, we summarize and analyze recent advances in materials concepts as well as in thin-film fabrication techniques for high-k (or high-capacitance) gate dielectrics when integrated with FSE-compatible semiconductors such as organics, metal oxides, quantum...