Ki Chang Kwon

Bio: Ki Chang Kwon is an academic researcher from Seoul National University. The author has contributed to research in topics: Graphene & Water splitting. The author has an hindex of 26, co-authored 61 publications receiving 2008 citations. Previous affiliations of Ki Chang Kwon include Chung-Ang University & Shenzhen University.

Increased Work Function in Few-Layer Graphene Sheets via Metal Chloride Doping

Abstract: A chemical approach to controlling the work function of few-layer graphene is investigated. Graphene films are synthesized on Cu foil by chemical vapor deposition. Six metal chlorides, AuCl3, IrCl3, MoCl3, OsCl3, PdCl2, and RhCl3, are used as dopants. The sheet resistance of the doped graphene decreases from 1100 Ω/sq to ≈500–700 Ω/sq and its transmittance at 550 nm also decreases from 96.7% to 93% for 20 mM AuCl3 due to the formation of metal particles. The sheet resistance and transmittance are reduced with increasing metal chloride concentration. The G peak in the Raman spectra is shifted to a higher wavenumber after metal chloride doping, which indicates a charge transfer from graphene to metal ions. The intensity ratio of ICC/IC−C increases with doping, indicating an electron transfer from graphene sheets to metal ions. Ultraviolet photoemission spectroscopy data shows that the work function of graphene increases from 4.2 eV to 5.0, 4.9, 4.8, 4.68, 5.0, and 5.14 eV for the graphene with 20 mM AuCl3, IrCl3, MoCl3, OsCl3, PdCl2, and RhCl3, respectively. It is considered that spontaneous charge transfer occurs from the specific energy level of graphene to the metal ions, thus increasing the work function.

Wafer-scale transferable molybdenum disulfide thin-film catalysts for photoelectrochemical hydrogen production

Abstract: We demonstrate that wafer-scale, transferable, and transparent thin-film catalysts based on MoS2, which consists of cheap and earth abundant elements, can provide a low onset potential of 1 mA cm−2 at 0.17 V versus a reversible hydrogen electrode and the high photocurrent density of 24.6 mA cm−2 at 0 V for a p-type Si photocathode. c-Domains with vertically stacked (100) planes in the transferable 2H-MoS2 thin films, which are grown via a thermolysis method, act as active sites for the hydrogen evolution reaction, and photogenerated electrons are efficiently transported through the n-MoS2/p-Si heterojunction.

Enhanced Endurance Organolead Halide Perovskite Resistive Switching Memories Operable under an Extremely Low Bending Radius

Abstract: It was demonstrated that organolead halide perovskites (OHPs) show a resistive switching behavior with an ultralow electric field of a few kilovolts per centimeter. However, a slow switching time and relatively short endurance remain major obstacles for the realization of the next-generation memory. Here, we report a performance-enhanced OHP resistive switching device. To fabricate topologically and electronically improved OHP thin films, we added hydroiodic acid solution (for an additive) in the precursor solution of the OHP. With drastically improved morphology such as small grain size, low peak-to-valley depth, and precise thickness, the OHP thin films showed an excellent performance as insulating layers in Ag/CH3NH3PbI3/Pt cells, with an endurance of over 103 cycles, a high on/off ratio of 106, and an operation speed of 640 μs and without electroforming. We suggest plausible resistive switching and conduction mechanisms with current–voltage characteristics measured at various temperatures and with dif...

Inhibition of Ion Migration for Reliable Operation of Organolead Halide Perovskite-Based Metal/Semiconductor/Metal Broadband Photodetectors

Abstract: Organolead halide perovskites (OHPs) have attracted extensive attention as light harvesting materials for solar cells recently, because of their high charge carrier mobility, high photoconversion efficiencies, low cost, and simple methodology. Despite these advantages, the OHPs exhibit sweep-dependent hysteresis behavior in current–voltage characteristics films, deteriorating the reliability of devices based on the OHPs. This study demonstrates reliable high on/off ratio (Ion/Ioff = 104) CH3NH3PbI3 broadband photodetectors with buffer layer-free simple metal/semiconductor/metal lateral structure. At high external bias, poor on/off ratios and spikes in dark current and photocurrent are observed due to the migration of charged defect ions. The ion migration can be effectively inhibited at low external bias, and thus the devices show high Ion/Ioff ratios and spike-free dark current and photocurrent. In addition, prevention of the prepoling in the CH3NH3PbI3 films by operating at the low external bias results in pronouncedly enhanced signal-to-noise ratios even under low intensity incident light. These results strongly propose that inhibiting the migration of charged defect ions in CH3NH3PbI3 films is a key in developing reliable high performance CH3NH3PbI3-based devices.

Highly selective and sensitive chemoresistive humidity sensors based on rGO/MoS2 van der Waals composites

Abstract: Reduced graphene oxide (rGO) and MoS2, the most representative two-dimensional (2D) materials, are receiving significant attention for the fabrication of sensing devices owing to their high surface area, many abundant sites, and excellent mechanical flexibility. Herein, we demonstrated chemoresistive humidity sensors with fast response, excellent selectivity, and ultrahigh sensitivity based on 2D rGO and 2D MoS2 hybrid composites (RGMSs). The RGMSs were fabricated by simple ultrasonication without the addition of additives and additional heating. Compared to pristine rGO, the RGMS exhibited a 200 times higher response to humidity at room temperature. The significant enhancement in the sensing performance of the composite was attributed to electronic sensitization due to p–n heterojunction formation and porous structures between rGO and MoS2. The synergistic combination of rGO and MoS2 could be applied to construct a flexible humidity sensor. The sensing performance of an RGMS flexible device remains the same before and after bending; this indicates that the use of rGO and MoS2 is a viable new and simple strategy to realize a humidity sensor for use in wearable electronics.

Graphene in Photocatalysis: A Review

Abstract: In recent years, heterogeneous photocatalysis has received much research interest because of its powerful potential applications in tackling many important energy and environmental challenges at a global level in an economically sustainable manner. Due to their unique optical, electrical, and physicochemical properties, various 2D graphene nanosheets-supported semiconductor composite photocatalysts have been widely constructed and applied in different photocatalytic fields. In this review, fundamental mechanisms of heterogeneous photocatalysis, including thermodynamic and kinetics requirements, are first systematically summarized. Then, the photocatalysis-related properties of graphene and its derivatives, and design rules and synthesis methods of graphene-based composites are highlighted. Importantly, different design strategies, including doping and sensitization of semiconductors by graphene, improving electrical conductivity of graphene, increasing eloectrocatalytic active sites on graphene, strengthening interface coupling between semiconductors and graphene, fabricating micro/nano architectures, constructing multi-junction nanocomposites, enhancing photostability of semiconductors, and utilizing the synergistic effect of various modification strategies, are thoroughly summarized. The important applications including photocatalytic pollutant degradation, H2 production, and CO2 reduction are also addressed. Through reviewing the significant advances on this topic, it may provide new opportunities for designing highly efficient 2D graphene-based photocatalysts for various applications in photocatalysis and other fields, such as solar cells, thermal catalysis, separation, and purification.

Stability of organic solar cells: challenges and strategies

Abstract: Organic solar cells (OSCs) present some advantages, such as simple preparation, light weight, low cost and large-area flexible fabrication, and have attracted much attention in recent years. Although the power conversion efficiencies have exceeded 10%, the inferior device stability still remains a great challenge. In this review, we summarize the factors limiting the stability of OSCs, such as metastable morphology, diffusion of electrodes and buffer layers, oxygen and water, irradiation, heating and mechanical stress, and survey recent progress in strategies to increase the stability of OSCs, such as material design, device engineering of active layers, employing inverted geometry, optimizing buffer layers, using stable electrodes and encapsulation. Some research areas of device stability that may deserve further attention are also discussed to help readers understand the challenges and opportunities in achieving high efficiency and high stability of OSCs towards future industrial manufacture.

Effect of airborne contaminants on the wettability of supported graphene and graphite

Abstract: It is generally accepted that supported graphene is hydrophobic and that its water contact angle is similar to that of graphite Here, we show that the water contact angles of freshly prepared supported graphene and graphite surfaces increase when they are exposed to ambient air By using infrared spectroscopy and X-ray photoelectron spectroscopy we demonstrate that airborne hydrocarbons adsorb on graphitic surfaces, and that a concurrent decrease in the water contact angle occurs when these contaminants are partially removed by both thermal annealing and controlled ultraviolet-O3 treatment Our findings indicate that graphitic surfaces are more hydrophilic than previously believed, and suggest that previously reported data on the wettability of graphitic surfaces may have been affected by unintentional hydrocarbon contamination from ambient air

Recent advances in metal sulfides: from controlled fabrication to electrocatalytic, photocatalytic and photoelectrochemical water splitting and beyond

Abstract: In recent years, nanocrystals of metal sulfide materials have attracted scientific research interest for renewable energy applications due to the abundant choice of materials with easily tunable electronic, optical, physical and chemical properties. Metal sulfides are semiconducting compounds where sulfur is an anion associated with a metal cation; and the metal ions may be in mono-, bi- or multi-form. The diverse range of available metal sulfide materials offers a unique platform to construct a large number of potential materials that demonstrate exotic chemical, physical and electronic phenomena and novel functional properties and applications. To fully exploit the potential of these fascinating materials, scalable methods for the preparation of low-cost metal sulfides, heterostructures, and hybrids of high quality must be developed. This comprehensive review indicates approaches for the controlled fabrication of metal sulfides and subsequently delivers an overview of recent progress in tuning the chemical, physical, optical and nano- and micro-structural properties of metal sulfide nanocrystals using a range of material fabrication methods. For hydrogen energy production, three major approaches are discussed in detail: electrocatalytic hydrogen generation, powder photocatalytic hydrogen generation and photoelectrochemical water splitting. A variety of strategies such as structural tuning, composition control, doping, hybrid structures, heterostructures, defect control, temperature effects and porosity effects on metal sulfide nanocrystals are discussed and how they are exploited to enhance performance and develop future energy materials. From this literature survey, energy conversion currently relies on a limited range of metal sulfides and their composites, and several metal sulfides are immature in terms of their dissolution, photocorrosion and long-term durability in electrolytes during water splitting. Future research directions for innovative metal sulfides should be closely allied to energy and environmental issues, along with their advanced characterization, and developing new classes of metal sulfide materials with well-defined fabrication methods.