Kiyohito Ishida

Bio: Kiyohito Ishida is an academic researcher from Tohoku University. The author has contributed to research in topics: Phase (matter) & Phase diagram. The author has an hindex of 76, co-authored 503 publications receiving 22744 citations. Previous affiliations of Kiyohito Ishida include Hitachi & Xiamen University.

Magnetic-field-induced shape recovery by reverse phase transformation.

Abstract: Large magnetic-field-induced strains1 have been observed in Heusler alloys with a body-centred cubic ordered structure and have been explained by the rearrangement of martensite structural variants due to an external magnetic field1,2,3. These materials have attracted considerable attention as potential magnetic actuator materials. Here we report the magnetic-field-induced shape recovery of a compressively deformed NiCoMnIn alloy. Stresses of over 100 MPa are generated in the material on the application of a magnetic field of 70 kOe; such stress levels are approximately 50 times larger than that generated in a previous ferromagnetic shape-memory alloy4. We observed 3 per cent deformation and almost full recovery of the original shape of the alloy. We attribute this deformation behaviour to a reverse transformation from the antiferromagnetic (or paramagnetic) martensitic to the ferromagnetic parent phase at 298 K in the Ni45Co5Mn36.7In13.3 single crystal.

Magnetic and martensitic transformations of NiMnX(X=In,Sn,Sb) ferromagnetic shape memory alloys

Abstract: Martensitic and magnetic transformations of the Heusler Ni50Mn50−yXy (X=In, Sn and Sb) alloys were investigated by differential scanning calorimetry measurement and the vibrating sample magnetometry technique. In all these alloy systems, the austenite phase with the ferromagnetic state was transformed into the martensite phase, which means that these Heusler alloys have potential as Ga-free ferromagnetic shape memory alloys (FSMAs). Furthermore, multiple martensitic transformations, such as two- or three-step martensitic transformations, occur in all these alloy systems. It was confirmed by transmission electron microscopy observation that the crystal structure of the martensite phase is an orthorhombic four-layered structure which has not been reported in other FSMAs. Therefore, the present Ga-free FSMAs have the great possibility of the appearance of a large magnetic-field-induced strain.

Cobalt-base high-temperature alloys

Abstract: We have identified cobalt-base superalloys showing a high-temperature strength greater than those of conventional nickel-base superalloys. The cobalt-base alloys are strengthened by a ternary compound with the L1 2 structure, \({\gamma}^{{^\prime}}\) Co 3 (Al,W), which precipitates in the disordered γ face-centered cubic cobalt matrix with high coherency and with high melting points. We also identified a ternary compound, \({\gamma}^{{^\prime}}\) Ir 3 (Al,W), with the L1 2 structure, which suggests that the Co-Ir-Al-W–base systems with \({\gamma}+{\gamma}^{{^\prime}}\) (Co,Ir) 3 (Al,W) structures offer great promise as candidates for next-generation high-temperature materials.

Ferrous Polycrystalline Shape-Memory Alloy Showing Huge Superelasticity

Abstract: Shape-memory alloys, such as Ni-Ti and Cu-Zn-Al, show a large reversible strain of more than several percent due to superelasticity. In particular, the Ni-Ti-based alloy, which exhibits some ductility and excellent superelastic strain, is the only superelastic material available for practical applications at present. We herein describe a ferrous polycrystalline, high-strength, shape-memory alloy exhibiting a superelastic strain of more than 13%, with a tensile strength above 1 gigapascal, which is almost twice the maximum superelastic strain obtained in the Ni-Ti alloys. Furthermore, this ferrous alloy has a very large damping capacity and exhibits a large reversible change in magnetization during loading and unloading. This ferrous shape-memory alloy has great potential as a high-damping and sensor material.

Metamagnetic shape memory effect in a Heusler-type Ni43Co7Mn39Sn11 polycrystalline alloy

Abstract: Shape memory and magnetic properties of a Ni43Co7Mn39Sn11 Heusler polycrystalline alloy were investigated by differential scanning calorimetry, the sample extraction method, and the three-terminal capacitance method. A unique martensitic transformation from the ferromagnetic parent phase to the antiferromagneticlike martensite phase was detected and magnetic-field-induced “reverse” transition was confirmed in a high magnetic field. In addition, a large magnetic-field-induced shape recovery strain of about 1.0% was observed to accompany reverse martensitic transformation, and the metamagnetic shape memory effect, which was firstly reported in a Ni45Co5Mn36.7In13.3 Heusler single crystal, was confirmed in a polycrystalline specimen.

Ferromagnetic materials

Abstract: In this chapter, we will restrict our attention to the ferrites and a few other closely related materials. The great interest in ferrites stems from their unique combination of a spontaneous magnetization and a high electrical resistivity. The observed magnetization results from the difference in the magnetizations of two non-equivalent sub-lattices of the magnetic ions in the crystal structure. Materials of this type should strictly be designated as “ferrimagnetic” and in some respects are more closely related to anti-ferromagnetic substances than they are to ferromagnetics in which the magnetization results from the parallel alignment of all the magnetic moments present. We shall not adhere to this special nomenclature except to emphasize effects, which are due to the existence of the sub-lattices.

Recent developments in stainless steels

Abstract: This article presents an overview of the developments in stainless steels made since the 1990s. Some of the new applications that involve the use of stainless steel are also introduced. A brief introduction to the various classes of stainless steels, their precipitate phases and the status quo of their production around the globe is given first. The advances in a variety of subject areas that have been made recently will then be presented. These recent advances include (1) new findings on the various precipitate phases (the new J phase, new orientation relationships, new phase diagram for the Fe–Cr system, etc.); (2) new suggestions for the prevention/mitigation of the different problems and new methods for their detection/measurement and (3) new techniques for surface/bulk property enhancement (such as laser shot peening, grain boundary engineering and grain refinement). Recent developments in topics like phase prediction, stacking fault energy, superplasticity, metadynamic recrystallisation and the calculation of mechanical properties are introduced, too. In the end of this article, several new applications that involve the use of stainless steels are presented. Some of these are the use of austenitic stainless steels for signature authentication (magnetic recording), the utilisation of the cryogenic magnetic transition of the sigma phase for hot spot detection (the Sigmaplugs), the new Pt-enhanced radiopaque stainless steel (PERSS) coronary stents and stainless steel stents that may be used for magnetic drug targeting. Besides recent developments in conventional stainless steels, those in the high-nitrogen, low-Ni (or Ni-free) varieties are also introduced. These recent developments include new methods for attaining very high nitrogen contents, new guidelines for alloy design, the merits/demerits associated with high nitrogen contents, etc.

Magnetic-field-induced shape recovery by reverse phase transformation.

Abstract: Large magnetic-field-induced strains1 have been observed in Heusler alloys with a body-centred cubic ordered structure and have been explained by the rearrangement of martensite structural variants due to an external magnetic field1,2,3. These materials have attracted considerable attention as potential magnetic actuator materials. Here we report the magnetic-field-induced shape recovery of a compressively deformed NiCoMnIn alloy. Stresses of over 100 MPa are generated in the material on the application of a magnetic field of 70 kOe; such stress levels are approximately 50 times larger than that generated in a previous ferromagnetic shape-memory alloy4. We observed 3 per cent deformation and almost full recovery of the original shape of the alloy. We attribute this deformation behaviour to a reverse transformation from the antiferromagnetic (or paramagnetic) martensitic to the ferromagnetic parent phase at 298 K in the Ni45Co5Mn36.7In13.3 single crystal.