Konrad Wissenbach

Bio: Konrad Wissenbach is an academic researcher from Fraunhofer Society. The author has contributed to research in topics: Selective laser melting & Laser. The author has an hindex of 37, co-authored 137 publications receiving 6738 citations. Previous affiliations of Konrad Wissenbach include RWTH Aachen University.

Laser additive manufacturing of metallic components: materials, processes and mechanisms

Abstract: Unlike conventional materials removal methods, additive manufacturing (AM) is based on a novel materials incremental manufacturing philosophy. Additive manufacturing implies layer by layer shaping and consolidation of powder feedstock to arbitrary configurations, normally using a computer controlled laser. The current development focus of AM is to produce complex shaped functional metallic components, including metals, alloys and metal matrix composites (MMCs), to meet demanding requirements from aerospace, defence, automotive and biomedical industries. Laser sintering (LS), laser melting (LM) and laser metal deposition (LMD) are presently regarded as the three most versatile AM processes. Laser based AM processes generally have a complex non-equilibrium physical and chemical metallurgical nature, which is material and process dependent. The influence of material characteristics and processing conditions on metallurgical mechanisms and resultant microstructural and mechanical properties of AM proc...

Ductility of a Ti‐6Al‐4V alloy produced by selective laser melting of prealloyed powders

Abstract: Purpose – The aim of the paper is the study of the change in the mechanical properties (and in particular in ductility), with the microstructure, of a biomedical Ti‐6Al‐4V alloy produced by different variants of selective laser melting (SLM).Design/methodology/approach – Ti‐6Al‐4V alloy produced by different variants of SLM has been mechanically characterized through tensile testing. Its microstructure has been investigated by optical observation after etching and by X‐ray diffraction analysis.Findings – SLM applied to Ti‐6Al‐4V alloy produces a material with a martensitic microstructure. Some microcracks, due the effect of incomplete homologous wetting and residual stresses produced by the large solidification undercooling of the melt pool, are observable in the matrix. Owing to the microstructure, the tensile strength of the additive manufactured parts is higher than the strength of hot worked parts, whereas the ductility is lower. A pre‐heating of the powder bed is effective in assisting remelting and ...

Additive manufacturing of ZrO2-Al2O3 ceramic components by selective laser melting

Abstract: Purpose – The purpose this paper is to develop an additive manufacturing (AM) technique for high‐strength oxide ceramics. The process development aims at directly manufacturing fully dense ceramic freeform‐components with good mechanical properties.Design/methodology/approach – The selective laser melting of the ceramic materials zirconia and alumina has been investigated experimentally. The approach followed up is to completely melt ZrO2/Al2O3 powder mixtures by a focused laser beam. In order to reduce thermally induced stresses, the ceramic is preheated to a temperature of at least 1,600°C during the build up process.Findings – It is possible to manufacture ceramic objects with almost 100 percent density, without any sintering processes or any post‐processing. Crack‐free specimens have been manufactured that have a flexural strength of more than 500 MPa. Manufactured objects have a fine‐grained two‐phase microstructure consisting of tetragonal zirconia and alpha‐alumina.Research limitations/implications...

I and i

Abstract: There is, I think, something ethereal about i —the square root of minus one. I remember first hearing about it at school. It seemed an odd beast at that time—an intruder hovering on the edge of reality. Usually familiarity dulls this sense of the bizarre, but in the case of i it was the reverse: over the years the sense of its surreal nature intensified. It seemed that it was impossible to write mathematics that described the real world in …

Additive manufacturing (3D printing): A review of materials, methods, applications and challenges

Abstract: Freedom of design, mass customisation, waste minimisation and the ability to manufacture complex structures, as well as fast prototyping, are the main benefits of additive manufacturing (AM) or 3D printing. A comprehensive review of the main 3D printing methods, materials and their development in trending applications was carried out. In particular, the revolutionary applications of AM in biomedical, aerospace, buildings and protective structures were discussed. The current state of materials development, including metal alloys, polymer composites, ceramics and concrete, was presented. In addition, this paper discussed the main processing challenges with void formation, anisotropic behaviour, the limitation of computer design and layer-by-layer appearance. Overall, this paper gives an overview of 3D printing, including a survey on its benefits and drawbacks as a benchmark for future research and development.

Metal Additive Manufacturing: A Review

Abstract: This paper reviews the state-of-the-art of an important, rapidly emerging, manufacturing technology that is alternatively called additive manufacturing (AM), direct digital manufacturing, free form fabrication, or 3D printing, etc. A broad contextual overview of metallic AM is provided. AM has the potential to revolutionize the global parts manufacturing and logistics landscape. It enables distributed manufacturing and the productions of parts-on-demand while offering the potential to reduce cost, energy consumption, and carbon footprint. This paper explores the material science, processes, and business consideration associated with achieving these performance gains. It is concluded that a paradigm shift is required in order to fully exploit AM potential.