Kumbakonam R. Rajagopal

Bio: Kumbakonam R. Rajagopal is an academic researcher from Texas A&M University. The author has contributed to research in topics: Constitutive equation & Viscoelasticity. The author has an hindex of 77, co-authored 659 publications receiving 23443 citations. Previous affiliations of Kumbakonam R. Rajagopal include Kent State University & University of Wisconsin-Madison.

On the modeling of quiescent crystallization of polymer melts

Abstract: In this paper we present a way of modeling crystallization in polymers within the confines of a new general framework that has been developed to describe materials undergoing dissipative processes. Crystallization in polymers is in general an irreversible process, and a characteristic of all such processes is the production of entropy. In addition to postulating constitutive forms for the internal energy and entropy, we prescribe a constitutive relation for the entropy production. This in turn aids in deriving the crystallization rate equation from the second law, under the constraint that all real processes tend to maximize the rate of entropy production. After developing the general framework, we derive specific models and compare the predictions of the model against experimental data available for quiescent crystallization in the literature. The predictions of the theory compare very well with the available experimental data for nylon-6 obtained by Patel and Spruiell (1).

An experimental investigation of the flow of dilute polymer solutions through corrugated channels

Abstract: Measurements of the velocity using Laser Doppler Velocimetry and normal stress are made for the flow of dilute polymer solutions through a channel with corrugated top and bottom plates. (Since we are dealing with non-Newtonian fluids, there can be significant contributions to the normal stress from non-linear terms in the constitutive expression, even when the flow is slow. The measurements being made are the normal stresses and not the “pressure”.) The surfaces of the plates are sinusoidal. A Reynolds number based on half the average plate spacing as the length scale and the characteristic velocity as the velocity scale was used and the range of Reynolds numbers studied was 50 < Re < 1000. The centerline velocities indicate that the experiments were performed in the inertial regime, as confirmed by the asymmetry of the centerline velocities along the channel length. The velocity profiles at the trough near the wall, for a channel with wavelength of 2.54 cm, indicate the presence of secondary flow. Sinusoidal plates with nearly identical aspect ratios (aλ) allowed for dramatic changes in the way in which the friction factor varied with Reynolds number, in that, in one case the friction factor associated with the fluid without polymer was higher than the friction factor associated with the fluid with polymer, while in others it was just the opposite. This would call into question the use of aspect ratio as an appropriate parameter for studying such problems. Changes in plate wavelength either increased or decreased the friction factor depending on the Reynolds number. Increasing plate amplitude increased the friction factor of the fluid for the range of values for the Reynolds number that was considered. The amplitude associated with the dimensionless normal stress increased with decreasing wavelength, for particular Reynolds numbers, irrespective of the fluid studied. Increasing the polymer concentration in the fluid decreased the difference in the amplitude of the dimensionless normal stress, the Reynolds number being fixed. Increasing the plate amplitude increased the amplitude of the normal stress, while an increase in plate wavelength decreased the amplitude of the normal stress.

A new constitutive framework for arterial wall mechanics and a comparative study of material models

Abstract: In this paper we develop a new constitutive law for the description of the (passive) mechanical response of arterial tissue. The artery is modeled as a thick-walled nonlinearly elastic circular cylindrical tube consisting of two layers corresponding to the media and adventitia (the solid mechanically relevant layers in healthy tissue). Each layer is treated as a fiber-reinforced material with the fibers corresponding to the collagenous component of the material and symmetrically disposed with respect to the cylinder axis. The resulting constitutive law is orthotropic in each layer. Fiber orientations obtained from a statistical analysis of histological sections from each arterial layer are used. A specific form of the law, which requires only three material parameters for each layer, is used to study the response of an artery under combined axial extension, inflation and torsion. The characteristic and very important residual stress in an artery in vitro is accounted for by assuming that the natural (unstressed and unstrained) configuration of the material corresponds to an open sector of a tube, which is then closed by an initial bending to form a load-free, but stressed, circular cylindrical configuration prior to application of the extension, inflation and torsion. The effect of residual stress on the stress distribution through the deformed arterial wall in the physiological state is examined. The model is fitted to available data on arteries and its predictions are assessed for the considered combined loadings. It is explained how the new model is designed to avoid certain mechanical, mathematical and computational deficiencies evident in currently available phenomenological models. A critical review of these models is provided by way of background to the development of the new model.

The physics of debris flows

Abstract: Recent advances in theory and experimen- tation motivate a thorough reassessment of the physics of debris flows. Analyses of flows of dry, granular solids and solid-fluid mixtures provide a foundation for a com- prehensive debris flow theory, and experiments provide data that reveal the strengths and limitations of theoret- ical models. Both debris flow materials and dry granular materials can sustain shear stresses while remaining stat- ic; both can deform in a slow, tranquil mode character- ized by enduring, frictional grain contacts; and both can flow in a more rapid, agitated mode characterized by brief, inelastic grain collisions. In debris flows, however, pore fluid that is highly viscous and nearly incompress- ible, composed of water with suspended silt and clay, can strongly mediate intergranular friction and collisions. Grain friction, grain collisions, and viscous fluid flow may transfer significant momentum simultaneously. Both the vibrational kinetic energy of solid grains (mea- sured by a quantity termed the granular temperature) and the pressure of the intervening pore fluid facilitate motion of grains past one another, thereby enhancing debris flow mobility. Granular temperature arises from conversion of flow translational energy to grain vibra- tional energy, a process that depends on shear rates, grain properties, boundary conditions, and the ambient fluid viscosity and pressure. Pore fluid pressures that exceed static equilibrium pressures result from local or global debris contraction. Like larger, natural debris flows, experimental debris flows of ;10 m 3 of poorly sorted, water-saturated sediment invariably move as an unsteady surge or series of surges. Measurements at the base of experimental flows show that coarse-grained surge fronts have little or no pore fluid pressure. In contrast, finer-grained, thoroughly saturated debris be- hind surge fronts is nearly liquefied by high pore pres- sure, which persists owing to the great compressibility and moderate permeability of the debris. Realistic mod- els of debris flows therefore require equations that sim- ulate inertial motion of surges in which high-resistance fronts dominated by solid forces impede the motion of low-resistance tails more strongly influenced by fluid forces. Furthermore, because debris flows characteristi- cally originate as nearly rigid sediment masses, trans- form at least partly to liquefied flows, and then trans- form again to nearly rigid deposits, acceptable models must simulate an evolution of material behavior without invoking preternatural changes in material properties. A simple model that satisfies most of these criteria uses depth-averaged equations of motion patterned after those of the Savage-Hutter theory for gravity-driven flow of dry granular masses but generalized to include the effects of viscous pore fluid with varying pressure. These equations can describe a spectrum of debris flow behav- iors intermediate between those of wet rock avalanches and sediment-laden water floods. With appropriate pore pressure distributions the equations yield numerical so- lutions that successfully predict unsteady, nonuniform motion of experimental debris flows.

Solving Ordinary Differential Equations

Abstract: Initial-value ordinary differential equation solution via variable order Adams method (SIVA/DIVA) package is collection of subroutines for solution of nonstiff ordinary differential equations. There are versions for single-precision and double-precision arithmetic. Requires fewer evaluations of derivatives than other variable-order Adams predictor/ corrector methods. Option for direct integration of second-order equations makes integration of trajectory problems significantly more efficient. Written in FORTRAN 77.

Hyperelastic modelling of arterial layers with distributed collagen fibre orientations

Abstract: Constitutive relations are fundamental to the solution of problems in continuum mechanics, and are required in the study of, for example, mechanically dominated clinical interventions involving soft biological tissues. Structural continuum constitutive models of arterial layers integrate information about the tissue morphology and therefore allow investigation of the interrelation between structure and function in response to mechanical loading. Collagen fibres are key ingredients in the structure of arteries. In the media (the middle layer of the artery wall) they are arranged in two helically distributed families with a small pitch and very little dispersion in their orientation (i.e. they are aligned quite close to the circumferential direction). By contrast, in the adventitial and intimal layers, the orientation of the collagen fibres is dispersed, as shown by polarized light microscopy of stained arterial tissue. As a result, continuum models that do not account for the dispersion are not able to capture accurately the stress–strain response of these layers. The purpose of this paper, therefore, is to develop a structural continuum framework that is able to represent the dispersion of the collagen fibre orientation. This then allows the development of a new hyperelastic free-energy function that is particularly suited for representing the anisotropic elastic properties of adventitial and intimal layers of arterial walls, and is a generalization of the fibre-reinforced structural model introduced by Holzapfel & Gasser (Holzapfel & Gasser 2001 Comput. Meth. Appl. Mech. Eng. 190, 4379–4403) and Holzapfel et al. (Holzapfel et al. 2000 J. Elast. 61, 1–48). The model incorporates an additional scalar structure parameter that characterizes the dispersed collagen orientation. An efficient finite element implementation of the model is then presented and numerical examples show that the dispersion of the orientation of collagen fibres in the adventitia of human iliac arteries has a significant effect on their mechanical response.