M.C. Ramaswamy

Bio: M.C. Ramaswamy is an academic researcher from Rajalakshmi Engineering College. The author has contributed to research in topics: Diesel fuel & Pyrolysis oil. The author has an hindex of 5, co-authored 7 publications receiving 570 citations.

The use of tyre pyrolysis oil in diesel engines

Abstract: Tests have been carried out to evaluate the performance, emission, and combustion characteristics of a single cylinder direct injection diesel engine fueled with 10%, 30%, and 50% of tyre pyrolysis oil (TPO) blended with diesel fuel (DF). The TPO was derived from waste automobile tyres through vacuum pyrolysis. The combustion parameters such as heat release rate, cylinder peak pressure, and maximum rate of pressure rise also analysed. Results showed that the brake thermal efficiency of the engine fueled with TPO-DF blends increased with an increase in blend concentration and reduction of DF concentration. NO(x), HC, CO, and smoke emissions were found to be higher at higher loads due to the high aromatic content and longer ignition delay. The cylinder peak pressure increased from 71 bars to 74 bars. The ignition delays were longer than with DF. It is concluded that it is possible to use tyre pyrolysis oil in diesel engines as an alternate fuel in the future.

Assessment of pyrolysis oil as an energy source for diesel engines

Abstract: This paper describes an experimental study of using tyre pyrolysis oil (TPO) obtained from waste automobile tyres by vacuum pyrolysis method, as a fuel in diesel engine. In this work, performance and emission parameters of a single cylinder water cooled diesel engine running on TPO diesel reference fuel (RF) blends in steps of 20% on volume basis of TPO, viz. TPO20 up to TPO70 were used as fuels and the results compared with diesel operation. Results indicated that reliable operation can be achieved up to 70% of TPO diesel blends. Thermal efficiencies were lower compared to diesel operation. Higher smoke, HC and CO emissions were recorded in the experimentation. Oil sticking was occasionally found on the nozzle stem and sac. There was no corrosion in the injection system after running the engine with TPO–RF blends.

Performance, emission and combustion studies of a DI diesel engine using Distilled Tyre pyrolysis oil-diesel blends

Abstract: Increase in energy demand, stringent emission norms and depletion of oil resources led the researchers to find alternative fuels for internal combustion engines. Many alternate fuels like Alcohols, Biodiesel, LPG, CNG etc have been already commercialized in the transport sector. In this context, pyrolysis of solid waste is currently receiving renewed interest. The disposal of waste tyres can be simplified to some extent by pyrolysis. The properties of the Tyre pyrolysis oil (TPO) derived from waste automobile tyres were analyzed and compared with the petroleum products and found that it can also be used as a fuel for compression ignition engine. However, the crude TPO has a higher viscosity and sulphur content. The crude TPO was desulphurised and then distilled through vacuum distillation. In the present work, DTPO-diesel blends were used as an alternate fuel in a diesel engine without any engine modification. This paper presents the studies on the performance, emission and combustion characteristics of a single cylinder four stroke air cooled DI diesel engine running with the Distilled Tyre pyrolysis oil (DTPO).

A comparative study on the performance, emission and combustion studies of a DI diesel engine using distilled tyre pyrolysis oil–diesel blends

Abstract: Alternate fuels like ethanol, biodiesel, LPG, CNG, etc., have been already commercialised in the transport sector. In this context, pyrolysis of solid waste is currently receiving renewed interest. The disposal of waste tyres can be simplified to a certain extent by pyrolysis. In the present work, the crude tyre pyrolyisis oil (TPO) was desulphurised and then distilled through vacuum distillation. Also, two distilled tyre pyrolysis oil (DTPO)–diesel fuel (DF) blends at lower and higher concentrations were used as fuels in a four stroke single cylinder air cooled diesel engine without any engine modification. The results were compared with diesel fuel (DF) operation. Results indicate that the engine can run with 90% DTPO and 10% diesel fuel.

Waste tyre pyrolysis – A review

Abstract: This review deals with the state-of-the-art of waste tyre pyrolysis for the first time in literature. Pyrolysis has been addressed as an attractive thermochemical process to tackle the waste tyre disposal problem while allowing energy recovery. Pyrolysis enables the separation of carbon black from tyres and the volatile matter released (condensable and non-condensable compounds) has the potential of renewable energy recovery given the significant proportion of natural rubber present in the tyre. Given this waste-to-energy pathway, a comprehensive review has been carried out in order to show the effects of the main process conditions (heating rate, temperature, pressure, carrier gas flow rate and type, volatiles residence time and pyrolysis time) on the physicochemical properties and distributions of the resulting products (gas, liquid and solid fractions). It has also been reviewed the influence of the size and composition of the feedstock. All reported results have been framed regarding the type of reactor as well as the experimental conditions used to avoid contradictions among the large number of publications on the subject. It is shown that the occurrence of secondary reactions is very sensitive to the interaction of the aforementioned variables. Also, the main properties of the pyrolytic products are pointed out. The liquid and gaseous fractions obtained are a valuable fuel source; while the solid fraction (char) has the recovery potential of low- grade carbon black or as carbon adsorbent after applying an activation step. Special attention has been given to the liquid fraction, highlighting its properties as alternative fuel in compression ignition engines.

Pyrolysis of waste tyres: a review.

Abstract: Approximately 1.5 billion tyres are produced each year which will eventually enter the waste stream representing a major potential waste and environmental problem. However, there is growing interest in pyrolysis as a technology to treat tyres to produce valuable oil, char and gas products. The most common reactors used are fixed-bed (batch), screw kiln, rotary kiln, vacuum and fluidised-bed. The key influence on the product yield, and gas and oil composition, is the type of reactor used which in turn determines the temperature and heating rate. Tyre pyrolysis oil is chemically very complex containing aliphatic, aromatic, hetero-atom and polar fractions. The fuel characteristics of the tyre oil shows that it is similar to a gas oil or light fuel oil and has been successfully combusted in test furnaces and engines. The main gases produced from the pyrolysis of waste tyres are H(2), C(1)-C(4) hydrocarbons, CO(2), CO and H(2)S. Upgrading tyre pyrolysis products to high value products has concentrated on char upgrading to higher quality carbon black and to activated carbon. The use of catalysts to upgrade the oil to a aromatic-rich chemical feedstock or the production of hydrogen from waste tyres has also been reported. Examples of commercial and semi-commercial scale tyre pyrolysis systems show that small scale batch reactors and continuous rotary kiln reactors have been developed to commercial scale.

Progress in used tyres management in the European Union: A review

Abstract: The dynamic increase in the manufacture of rubber products, particularly those used in the automobile industry, is responsible for a vast amount of wastes, mostly in the form of used tyres, of which more than 17 million tonnes are produced globally each year. The widely differing chemical compositions and the cross-linked structures of rubber in tyres are the prime reason why they are highly resistant to biodegradation, photochemical decomposition, chemical reagents and high temperatures. The increasing numbers of used tyres therefore constitute a serious threat to the natural environment. The progress made in recent years in the management of polymer wastes has meant that used tyres are starting to be perceived as a potential source of valuable raw materials. The development of studies into their more efficient recovery and recycling, and the European Union's restrictive legal regulations regarding the management of used tyres, have led to solutions enabling this substantial stream of rubber wastes to be converted into energy or new polymer materials. In this article we present the relevant literature describing innovative organizational approaches in the management of used tyres in the European Union member countries and the possible uses of waste tyres as a source of raw materials or alternative fossil fuels.

Influence of injection timing on performance, emission and combustion characteristics of a DI diesel engine running on waste plastic oil

Abstract: Environmental concern and availability of petroleum fuels have caused interests in the search for alternate fuels for internal combustion engines. Waste plastics are indispensable materials in the modern world and application in the industrial field is continually increasing. In this context, waste plastics are currently receiving renewed interest. As an alternative, non-biodegradable, and renewable fuel, waste plastic oil is receiving increasing attention. The waste plastic oil was compared with the petroleum products and found that it can also be used as fuel in compression ignition engines. In the present work, the influence of injection timing on the performance, emission and combustion characteristics of a single cylinder, four stroke, direct injection diesel engine has been experimentally investigated using waste plastic oil as a fuel. Tests were performed at four injection timings (23°,20°,17° and 14° bTDC). When compared to the standard injection timing of 23° BTDC the retarded injection timing of 14° bTDC resulted in decreased oxides of nitrogen, carbon monoxide and unburned hydrocarbon while the brake thermal efficiency, carbon dioxide and smoke increased under all the test conditions.

Performance, emission and combustion characteristics of a DI diesel engine using waste plastic oil

Abstract: Increase in energy demand, stringent emission norms and depletion of oil resources have led the researchers to find alternative fuels for internal combustion engines. On the other hand waste plastic pose a very serious environment challenge because of their disposal problems all over the world. Plastics have now become indispensable materials in the modern world and application in the industrial field is continually increasing. In this context, waste plastic solid is currently receiving renewed interest. The properties of the oil derived from waste plastics were analyzed and compared with the petroleum products and found that it has properties similar to that of diesel. In the present work, waste plastic oil was used as an alternate fuel in a DI diesel engine without any modification. The present investigation was to study the performance, emission and combustion characteristics of a single cylinder, four-stroke, air-cooled DI diesel engine run with waste plastic oil. The experimental results have showed a stable performance with brake thermal efficiency similar to that of diesel. Carbon dioxide and unburned hydrocarbon were marginally higher than that of the diesel baseline. The toxic gas carbon monoxide emission of waste plastic oil was higher than diesel. Smoke reduced by about 40% to 50% in waste plastic oil at all loads.