In linear IC's fabricated in a low-voltage CMOS technology, the reduction of the dynamic range due to the dc offset and low frequency noise of the amplifiers becomes increasingly significant. Also, the achievable amplifier gain is often quite low in such a technology, since cascoding may not be a practical circuit option due to the resulting reduction of the output signal swing. In this paper, some old and some new circuit techniques are described for the compensation of the amplifier's most important nonideal effects including the noise (mainly thermal and 1/f noise), the input-referred dc offset voltage as well as the finite gain resulting in a nonideal virtual ground at the input.

Circuit techniques for reducing the effects of op-amp imperfections: autozeroing, correlated double sampling, and chopper stabilization

There is a need among scientists and clinicians for low-noise low-power biosignal amplifiers capable of amplifying signals in the millihertz-to-kilohertz range while rejecting large dc offsets generated at the electrode-tissue interface. The advent of fully implantable multielectrode arrays has created the need for fully integrated micropower amplifiers. We designed and tested a novel bioamplifier that uses a MOS-bipolar pseudoresistor element to amplify low-frequency signals down to the millihertz range while rejecting large dc offsets. We derive the theoretical noise-power tradeoff limit - the noise efficiency factor - for this amplifier and demonstrate that our VLSI implementation approaches this limit by selectively operating MOS transistors in either weak or strong inversion. The resulting amplifier, built in a standard 1.5-/spl mu/m CMOS process, passes signals from 0.025Hz to 7.2 kHz with an input-referred noise of 2.2 /spl mu/Vrms and a power dissipation of 80 /spl mu/W while consuming 0.16 mm/sup 2/ of chip area. Our design technique was also used to develop an electroencephalogram amplifier having a bandwidth of 30 Hz and a power dissipation of 0.9 /spl mu/W while maintaining a similar noise-power tradeoff.

A low-power low-noise CMOS amplifier for neural recording applications

A technique that combines the high-frequency behavior of a single-stage op amp with the high DC gain of a multistage design is presented. This technique is based on the concept that a very high DC gain can be achieved in combination with any unity-gain frequency achievable by a (folded-) cascode design. Bode-plot measurements for an op amp realized in a 1.6- mu m process show a DC gain of 90 dB and a unity-gain frequency of 116 MHz (16-pF load). Settling measurements with a feedback factor of 1/3 show a fast single-pole settling behavior corresponding to a closed-loop bandwidth of 18 MHz (35-pF load) and a settling accuracy better than 0.03%. This technique does not cause any loss in output voltage swing. At a supply voltage of 5.0 V an output swing of about 4.2 V is achieved without loss in DC gain. The above advantages are achieved with a 30% increase in chip area and a 15% increase in power consumption. >

A fast-settling CMOS op amp for SC circuits with 90-dB DC gain

Basic properties of the operational transconductance amplifier (OTA) are discussed. Applications of the OTA in voltage-controlled amplifiers, filters, and impedances are presented. A versatile family of voltage-controlled filter sections suitable for systematic design requirements is described. The total number of components used in these circuits is small, and the design equations and voltage-control characteristics are attractive. Limitations as well as practical considerations of OTA-based filters using commercially available bipolar OTAs are discussed. Applications of OTAs in continuous-time monolithic filters are considered.

/pdf/active-filter-design-using-operational-transconductance-2mzdfyvyv6.pdf

Active filter design using operational transconductance amplifiers: A tutorial

This survey presents an overview of recent advances in the state of the art for computer-aided design (CAD) tools for analog and mixed-signal integrated circuits (ICs). Analog blocks typically constitute only a small fraction of the components on mixed-signal ICs and emerging systems-on-a-chip (SoC) designs. But due to the increasing levels of integration available in silicon technology and the growing requirement for digital systems to communicate with the continuous-valued external world, there is a growing need for CAD tools that increase the design productivity and improve the quality of analog integrated circuits. This paper describes the motivation and evolution of these tools and outlines progress on the various design problems involved: simulation and modeling, symbolic analysis, synthesis and optimization, layout generation, yield analysis and design centering, and test. This paper summarizes the problems for which viable solutions are emerging and those which are still unsolved.

/pdf/computer-aided-design-of-analog-and-mixed-signal-integrated-23xbvj9rc2.pdf

Computer-aided design of analog and mixed-signal integrated circuits

A general theory that allows the accurate linear and nonlinear analysis of any crystal oscillator circuit is presented. It is based on the high Q of the resonator and on a very few nonlimiting assumptions. The special case of the three-point oscillator, that includes Peirce and one-pin circuits, is analyzed in more detail. A clear insight into the linear behavior, including the effect of losses, is obtained by means of the circular locus of the circuit impedance. A basic condition for oscillation and simple analytic expressions are derived in the lossless case for frequency pulling, critical transconductance, and start-up time constant. The effects of nonlinearities on amplitude and on frequency stability are analyzed. As an application, a 2-MHz CMOS oscillator which uses amplitude stabilization to minimize power consumption and to eliminate the effects of nonlinearities on frequency is described. The chip, implemented in a 3- mu m p-well low-voltage process, includes a three-stage frequency divider and consumes 0.9 mu A at 1.5 V. The measured frequency stability is 0.05 p.p.m./V in the range 1.1-5 V of supply voltage. Temperature effect on the circuit itself is less than 0.1 p.p.m. from -10 to +60 degrees C. >

High-performance crystal oscillator circuits: theory and application

A design system has been developed which is able to design transconductance amplifiers, operational amplifiers, low-noise BIMOS amplifiers, voltage and current references, quartz oscillators, comparators, and oversampled A/D converters including their digital decimation filter starting from building-block and technology specifications. This design system, called Interactive Design for Analog Circuits (IDAC), is able to size a library of analog schematics (actually more than 40) as a function of technology (p-well and n-well CMOS) and desired building-block specifications. IDAC also generates a complete data sheet, an input file for SPICE2, and an input file for the analog layout program ILAC.

IDAC: an interactive design tool for analog CMOS circuits

Two transconductance amplifiers are presented in which the concept of an input dependent bias current has been introduced. As a result, these amplifiers combine a very low standby power dissipation with a high driving capability. The first amplifier, suited for SC filters, is fairly small (0.075 mm/SUP 2/) and has a slew rate which is more than an order of magnitude better than micropower amplifiers presented earlier. The second amplifier can be used as a micropower buffer. Nearly the whole supply current is used to charge the load capacitor so that this amplifier has a high efficiency.

Adaptive biasing CMOS amplifiers

A CMOS switched capacitor instrumentation amplifier is presented. Offset is reduced by an auto-zero technique and effects due to charge injection are attenuated by a special amplifier configuration. The circuit which is realized in a 4-/spl mu/m double poly process has an offset (/spl tau/) of 370 /spl mu/V, an rms input referred integrated noise (0.5 -f/sub c//2) of 79 /spl mu/V, and consumes only 21 /spl mu/W (f/sub c/ = 8 kHz, V/sub DD/ = 3 V).

A Micropower CMOS-Instrumentation Amplifier

A CMOS switched capacitor instrumentation amplifier is presented. Offset is reduced by an auto-correlation technique and effects due to charge injection are attenuated by a special amplifier configuration. The circuit which is realized in a 4 ?m double poly process has a typical offset (?) of 370 ?V, an RMS input referred integrated noise (0-f c /2) of 79 ?V and consumes only 21 ?W (f c = 8 kHz, V DD = 3 V).

M. Degrauwe

Papers

High-performance crystal oscillator circuits: theory and application

IDAC: an interactive design tool for analog CMOS circuits

Adaptive biasing CMOS amplifiers

A Micropower CMOS-Instrumentation Amplifier

A Micropower CMOS-Instrumentation Amplifier